Form No. 7102557 (Rev. ‘-’, 5/2/2008) TP 1099-5398---TC-N

SLT24520FC

Unit Features and Controls

Quick Setup Guide

Lawn Tractor Model SLT24520FC

1 Unpack the Unit

• Remove all packaging materials from the crate and the unit. Remove any banding securing the unit to the crate.

• Locate and identify the items included with the unit.

Questions?

Do not return to the store. We can help.

Call Customer Service Toll-Free 1-800-317-7833Or visit our website www.snapper.com

DANGER

Amputation hazard

Roll-over hazard

Rotating blades cut off arms and legs.

Operating on slopes can cause loss of

• Stop the mower when children or others are

control and roll-overs.

10º Max.

• If you cannot back-up a hill, do not drive

Steering Wheel

Speed Control Pedal

2 Read the Manuals

• Carefully read all the manuals supplied with the unit. They contain important safety, operating, and maintenance information.

near.

 

on it.

• Do not carry riders (especially children) even

 

with the blades off. They may fall off or return

 

• If machine stops while going uphill,

for another ride when you are not expecting it.

 

stop the blades and back down slowly.

• Look down and behind before and while

10º Max.

• Avoid sudden turns.

backing.

• Go up and down slopes, not across.

 

Tractor

Hood

Seat

Battery

3

Install the Seat

Insert the two posts under the seat (A, Figure 1) into the rear adjustment slots in the hinge plate (B).

Install the two wing bolts and small washers (C) through the front adjustment slots in the hinge plate and into the threaded holes under the seat.

Adjust the seat as desired, then tighten the wing bolts.

B

A

Figure 1

C

 

Fire hazard

Carbon monoxide hazard

Gasoline is flammable. Yard debris is combustible.

The engine emits poisonous carbon

• Allow engine to cool for at least 3 minutes

monoxide gas.

before refueling.

• Avoid inhaling exhaust fumes.

• Keep unit cleaned of debris.

• Only operate outdoors.

WARNING

Avoid serious injury or death:

• Know the location and function of

• Remove objects that could be thrown by the blade.

all controls.

• Be sure blade(s) and engine are stopped before

Deck Lift

Lever

4 Install the Steering Wheel

Turn the front wheels of the tractor straight ahead.

Install the steering shaft bellows (Figure 2) over the steering shaft.

• Keep safety devices (guards, shields, placing hands or feet near blade(s).

• Read the operator's manual

switches, etc.) in place and working. • When leaving machine, shut off, remove key, and

before using this product.

set parking brake.

 

Brake

Pedal

Throttle

Control

Mower

Deck

Choke

ControlPTO (Blade

Engage)

Switch

Cruise

Control

• Install the steering wheel (Figure 3) onto the steering shaft, making sure the

steering wheel is aligned straight.

Figure 2

Fasten the steering wheel to the steering shaft with the hex bolt and large washer. Tighten securely.

Attach the steering wheel cover (Figure 4) to the center of the steering wheel.

Figure 3

Figure 4

9 Start the Engine

• Sit in the seat.

Engage the parking brake: Press the brake pedal (Figure

7) down, and pull the parking brake lever (A, Figure 8) up. Figure 7

Push the PTO (blade engage) switch (B, Figure 8) to

OFF (‘O’).

A

B

• Move the throttle control (A, Figure 9) to FAST.

 

 

• Move the choke control (B, Figure 9) to CHOKE.

Turn the ignition key (C, Figure 8) to START.

Figure 9

After the engine starts, release the ignition key,

 

 

B

A

Figure 8

C

 

Steering Wheel

(Removed for Clarity)

Reverse

Mowing Option

(RMO) Switch

Ignition

Switch

Parking Brake

Lever

5 Connect the Battery

Raise the seat.

Check the date on the top or side of the battery. If the unit is being put into service after the date indicated on the battery, charge the battery for one hour at 6-10 amps.

Install the terminal cover (not shown) onto the red cable.

Connect the red cable to the positive (+) battery terminal (A, Figure 5) with a carriage bolt and wing nut. Tighten securely. Slide the terminal cover over the connection.

Connect the black cable to the negative (-) battery terminal (B, Figure 5) with a carriage bolt and wing nut. Tighten securely.

Lower the seat.

A

B

Figure 5

and move the choke control to OFF.

Note: Always set the throttle control to FAST when driving and mowing.

10 Drive the Unit Off the Crate

Move the deck lift lever (Figure 12) to the highest cutting height.

Disengage the parking brake: Press and release the brake pedal.

• Slowly press the speed control pedal (Figure 10) forward to drive the unit Figure 10 off the crate.

If the unit does not move, set the automatic drive disconnect (Figure 11) to DRIVE.

Items Needed for Assembly

Utility Knife

6-10 Amp Battery Charger

Pry Bar

Tire Pressure Gauge

• Tin Snips or Banding Cutter

3/8” Socket Wrench

Unleaded Fuel (Minimum of 87 Octane)

Items Included with Unit

Manual Packet

• Hardware Bag including:

Seat

Wing Bolt (2)

Steering Wheel

Small Washer (2)

Steering Shaft Bellows

Hex Bolt (1)

Steering Wheel Cover

Large Washer (1)

 

 

Carriage Bolt (2)

 

 

Wing Nut (2)

 

 

Terminal Cover

• Set of two Ignition Keys

6 Check the Tire Pressure

Adjust the pressure of the front and rear tires to 14 PSI. Note: The tires may be overinflated for shipping purposes.

7 Check the Engine Oil Level

Note: The engine is shipped with oil. However, the oil level should be checked before attempting to start the engine.

Move the tractor to a flat, level surface.

Raise the tractor hood to access the engine compartment.

Remove the oil fill cap (A, Figure 6). Wipe the dipstick, replace the cap, then remove and check the oil level. The oil level should be between the ‘Full’ and ‘Add’ marks on the dipstick.

If necessary, add premium 10W-30 oil to the engine. Recheck the oil level.

Replace and secure the oil fill cap.

8 Add Fuel

Remove the fuel cap (B, Figure 6).

Add clean, fresh, unleaded fuel with a minimum of 87 octane to the fuel tank.

Replace the fuel cap, and wipe up any fuel that may have spilled.

Lower the tractor hood.

A

B

Figure 6

Figure 11

11 Mowing

Read the Operator’s Manual before mowing.

Move the deck lift lever (Figure 12) to the desired cutting height.

Pull the PTO (blade engage) switch (Figure 13) to ON (‘I’).

• Begin mowing.

Figure 12

WARNING: Do not use the Reverse Mowing Option (RMO) feature until you have carefully read the Reverse Mowing Option Section of the Operator’s Manual.

Figure 13

12 Stopping the Tractor, Blades, and Engine

• Slowly release the speed control pedal.

• Push the PTO (blade engage) switch down to OFF (‘O’).

Engage the parking brake: Press the brake pedal, and pull the parking brake lever up.

Move the throttle control to SLOW.

© Briggs & Stratton Corporation

We reserve the right to improve our products and make changes in specifications, designs, and standard equipment without notice and without incurring obligation.

• Turn the ignition key to OFF (‘O’). Remove the key.

Page 1
Image 1
Snapper SLT24520FC setup guide Unit Features and Controls, Unpack the Unit, Read the Manuals, Install the Steering Wheel

SLT24520FC specifications

The Snapper SLT24520FC is a powerful and versatile lawn tractor designed to meet the needs of homeowners who expect reliability and efficiency from their outdoor equipment. This model features a robust 24 HP Briggs & Stratton engine, ensuring plenty of power to handle a variety of mowing tasks with ease. The engine is equipped with a hydrostatic transmission that provides smooth operation and an effortless driving experience. This feature allows for infinite speed control, enabling users to navigate their lawns efficiently.

One of the standout characteristics of the SLT24520FC is its 48-inch cutting deck, which includes three durable, double-welded steel blades. This wide deck not only allows for faster mowing but also offers superior cutting performance, producing clean and precise trims on different types of grass. The adjustable cutting height offers six positions, ranging from 1.5 to 4 inches, allowing users to customize their lawn’s appearance based on personal preference and seasonal growth.

In terms of comfort and usability, the Snapper SLT24520FC boasts an ergonomic seating position, featuring a high-back seat for maximum support during long mowing sessions. The tractor also comes with a convenient steering wheel design that enables easy maneuverability around obstacles and tight corners.

Technologically, the SLT24520FC is equipped with the company’s signature ReadyStart technology, which simplifies starting the engine. This technology eliminates the need for priming or choking, allowing users to start the tractor quickly and reliably, even in varying weather conditions. Additionally, the tractor features an electric PTO engagement that makes switching the mowing blades on and off a breeze.

For added functionality, the SLT24520FC supports optional attachments, including baggers, mulching kits, and snow throwers, transforming it into an all-season tool for yard management. The durable construction, coupled with a five-year limited warranty, ensures that this lawn tractor delivers consistent performance year after year.

Overall, the Snapper SLT24520FC offers a blend of power, precision, and convenience, making it an ideal choice for those looking to maintain a pristine lawn with minimal effort.