4
5
6
7
8
3
4
GUI MODE | 9 |
/ , / | 10 |
/ , / | 11 / , |
/ ,
13
/ , ,
Calibrating the appropriate speaker settings automatically (Auto Calibration)
You can set up the speakers to obtain the desired sound from all connected speakers automatically by using the auto calibration function.
Before you perform the auto calibration
During the calibration, the sound that comes out of the speakers is very loud. Pay attention to the presence of children or to the effect on your neighborhood.
Perform the measurement in a quiet environment to avoid the effect of noise and get a more accurate measurement.
If there are any obstacles in the path between the optimizer microphone and the speakers, the calibration cannot be performed correctly. Remove any obstacle from the measurement area to avoid measurement error.
1 Install and connect the speakers and TV.
For detail, see front page.
2 Connect the supplied optimizer microphone to the AUTO CAL MIC jack.
The AUTO CAL MIC jack is used for the supplied optimizer microphone only. Do not connect other microphones. Doing so may damage the receiver and the microphone.
3 Set up the optimizer microphone.
Place the optimizer microphone at your seating position. Use a stool or tripod so that the optimizer microphone remains at the same height as your ears. Orient the L end of the optimizer microphone toward the front left speaker and the R end of the optimizer microphone toward the front right speaker.
On setting up the active subwoofer
When a subwoofer is connected, turn on the subwoofer and turn up the volume beforehand. Turn the MASTER VOLUME knob to just before the
If you connect a subwoofer with the crossover frequency function, set the value to maximum.
If you connect a subwoofer with an auto standby function, set it to off (deactivated).
Performing auto calibration
The auto calibration function allows you to measure the following: speaker connections, polarity of speakers, speaker distance, speaker angle, speaker size, speaker level, frequency characteristics.
1 Connect a TV monitor to this receiver.
Refer to “3: Connecting the monitor” in the operating instructions.
2 Turn on the receiver and the TV.
Switch the input of the TV so that an image of the menu is displayed.
3 Press AMP.
The receiver can be operated using the remote.
4 Press GUI MODE.
After “GUI MODE ON” has appeared in the display window of the receiver, “GUI MODE” appears.
The menu is displayed on the TV screen.
5 Press /repeatedly to select “ Settings,” then press or .
The Settings menu list appears on the TV screen.
6 Press /repeatedly to select “Auto Calibration,” then pressor .
7 Press /repeatedly to select “Quick Setup,” then press .
The screen on which you can select the item to be measurered appears.
8 Press /repeatedly and to
The confirmation screen, asking whether you are ready to start measurement, appears.
9 Press to select “Start.”
The measurement starts in five seconds.
When the measurement ends, a beep sounds and the measurement result appears on the TV screen.
10 Pressto select “Next.”
11 Press /repeatedly to select “Yes,” then press
.
The selecting screen of the calibration type appears.
12 Press /repeatedly to select the auto calibration type, then press.
Parameter ExplanationFull Flat | Makes the measurement of frequency from |
| each speaker flat. |
Engineer | Sets the frequency to one that matches that |
| of the Sony listening room standard. |
Front Reference | Adjusts the characteristics of all the |
| speakers to match the characteristics of the |
| front speaker. |
OFF | Sets the auto calibration EQ to off. |
The measurement results are saved.
13 Press .
The exit screen appears.
14 Press.
When error codes appear
When “Save auto calibration (auto speaker setup)?” appears on the TV screen in step 10, you can select whether to confirm the warning (“Yes”) or not (“No”). Follow the instructions of the TV screen when you select “Yes.” For details on warning and error codes, see “Message list after auto calibration measurement” in “9: Calibrating the appropriate speaker settings automatically (Auto Calibration)” in the operating instructions.
TipThe size of a speaker (LARGE/SMALL) is determined by the low characteristics. The measurement results may vary, depending on the position of the optimizer microphone and speakers, and the shape of the room. It is recommended that you follow the measurement results. However, you can change those settings in the Speaker settings menu. Save the measurement results first, then try to change the settings if you want.
To select the language displayed on the TV screen
You can select the language to be used for messages on the TV screen from 4 languages.
English
Español
Français
Deutsch
For details, see “ System settings” in the operation instructions.
Setting up other components
You should set up each component so that take out sound is output from speakers correctly when you play back a connected component. The following case describes Sony components. Refer to the operating instructions supplied with each component.
Sony Super Audio CD player
Select a suitable playback area
After the setting
The receiver is now ready to use. Refer to the operating instruction supplied with the receiver for details.