3-263-410-11(1)

FM/AM

Compact Disc

Player

Installation/Connections
Installation/Connexions

CDX-F7005X

CDX-F7000

© 2004 Sony Corporation Printed in Korea

2

A

AUDIO OUT

 

FRONT

 

SUB OUT (MONO)

AUDIO OUT

REAR

B

BUS AUDIO IN

 

BUS CONTROL IN

BUS AUDIO IN

Source selector*

Sélecteur de source*

XA-C30

BUS CONTROL IN

* not supplied

non fourni

1

1

2

3

⋅ 4

45

⋅ 2

Equipment used in illustrations (not supplied) Appareils utilisés dans les illustrations (non fournis)

Cautions
•This unit is designed for negative ground 12 V DC operation only.

•Do not get the leads under a screw, or caught in moving parts (e.g. seat railing).

•Before making connections, turn the car ignition off to avoid short circuits.

•Connect the yellow and red power input leads only after all other leads have been connected.

Run all ground leads to a common ground point.

•Be sure to insulate any loose unconnected leads with electrical tape for safety.

•The use of optical instruments with this product will increase eye hazard.
Notes on the power supply lead (yellow)

•When connecting this unit in combination with other stereo components, the connected car circuit’s rating must be higher than the sum of each component’s fuse.

•When no car circuits are rated high enough, connect the unit directly to the battery.

Parts Iist (1)
Connection example (2)

Notes (2-A)

Be sure to connect the ground lead before connecting the amplifier.

If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated.

Tip (2-B- )

For connecting two or more CD/MD changers, the source selector XA-C30 (optional) is necessary.

Connection diagram (3)

1To a metal surface of the car

First connect the black ground lead, then connect the yellow and red power input leads.

2To the power antenna control lead or power supply lead of antenna booster amplifier

Notes

It is not necessary to connect this lead if there is no power antenna or antenna booster, or with a manually-operated telescopic antenna.

When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.”

Front speaker

Power amplifier

Haut-parleur avant

Amplificateur de puissance

Rear speaker

CD/MD changer

Haut-parleur arrière

Changeur de CD/MD

Active subwoofer

Rotary commander RM-X4S

Caisson de graves actif

Satellite de commande RM-X4S

•The numbers in the list are keyed to those in the instructions.

•The bracket 1 and the protection collar 3 are attached to the unit before shipping. Before mounting the unit, use the release keys 5 to remove the bracket 1 and the protection collar

3 from the unit. For details, see “Removing the protection collar and the bracket (4)” on the reverse side of the sheet.

Keep the release keys 5 for future use as they are also necessary if you remove the unit from your car.

Caution
Handle the bracket 1 carefully to avoid injuring your fingers.

1

Catch

Note

Before installing, make sure that the catches on both sides of the bracket 1 are bent inwards 2 mm (3/32 in). If the catches are straight or bent outwards,

the unit will not be installed securely and may spring out.

3To AMP REMOTE IN of an optional power amplifier

This connection is only for amplifiers. Connecting any other system may damage the unit.

4To the interface cable of a car telephone

5 To a car’s illumination signal

Be sure to connect the black ground lead to a metal surface of the car first.

6 To the +12 V power terminal which is energized in the accessory position of the ignition key switch

Notes

If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times.

Be sure to connect the black ground lead to a metal surface of the car first.

When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.”

7To the +12 V power terminal which is energized at all times

Be sure to connect the black ground lead to a metal surface of the car first.