To protect your hearing (AVLS)

The AVLS (Automatic Volume Limiter
System) function keeps down the maximum
volume to protect your ears.
Set AVLS to LIMIT.
The AVLS indication appears.
Note
•If the sound is distorted when you listen to the
bass-boosted sound with the AVLS function,
turn down the volume.

To resume playing from the point

you stopped the CD (Resume Play)

Normally, every time you stop and play,
playing starts from the beginning of the CD.
The resume play function, however, let you
listen to from the point where you last turned
off the player.
Set RESUME to ON.
To cancel resume play, set RESUME to OFF.
Notes
•Even if RESUME is set to ON, playing starts
from the beginning when you open the lid.
•The resume point may be inaccurate by about
30 seconds.

To turn off the beep

You can turn off the beep that sounds as you
operate your player.
Disconnect the power source (AC power
adaptor, rechargeable battery or alkaline
batteries). While you press and hold down p,
connect the power source again. To make the
beep sound again, disconnect the power
source, and then connect it without pressing
p.

Connecting to other

stereo equipment

You can listen to the CD through other stereo
equipment or record a CD on a cassette tape.
Refer to the instruction manual of the other
equipment for details. Before making
connections, turn off each piece of equipment.

zPower Sources

Using rechargeable

battery

Charge the rechargeable battery before using it
for the first time.
Use only BP-DM10 or BP-DM20 rechargeable
battery for this player. Do not use any other
rechargeable batteries.
You can use BP-DM10 and BP-DM20 in the
same way, but their charging time and battery
life are different. Check the model number of
your rechargeable battery before using it.
1Open the lid of the battery compartment.
2Insert the rechargeable battery so that the
word “SONY” is facing the same
direction as illustrated inside the lid, and
close the lid.
3Connect the AC power adaptor.
The indication “CHG” lights up. Charge
for about 2 hours (for BP-DM10) or 3.5
hours (for BP-DM20).
(If the battery has been fully charged,
“CHG“ and flash. )
4When fully charged, “CHG” disappears.
Disconnect the AC power adaptor.

When to charge the battery

When the battery becomes weak,
indication appears in the display. If the “Lo
batt” appears in the display, charge the
rechargeable battery, because the battery is
used up.
To keep the original battery capacity for a
long time, recharge the battery when the
battery is used up (discharged).
Notes
•Charging time varies depending on how the
rechargeable battery is used.
•If the battery is new or has not been used for a
long time, it may not be charged completely
until you charge and discharge it several times.
•If the battery life becomes shorter by about
half, replace it with Sony BP-DM10 or BP-
DM20 rechargeable battery. Do not use any
other rechargeable battery (R6 type
rechargeable battery, etc.).
DC IN 4.5 V
AC power adaptor
to a wall outlet
Notes
•When you use a connecting cord, the SOUND
function will be disabled.
•Before you play the CD, turn down the volume
of the connected equipment so as not to
damage the connected speakers.
•The beep sound is not output from the LINE
OUT jack.
•When you connect other equipment to the
LINE OUT jack of this player, adjust the
volume on the connected equipment.
•When you record a CD on a cassette tape using
a tape recorder that has the blank search
function, release the ESP function. If the ESP
function is on, the blank search function does
not work.

Playing a CD in a car

You can use your player in a car as illustrated
below.
To connect your player to a car cassette deck,
you need the following accessories:
•Car connecting pack
•Car battery cord
or,
•Mount kit CPM-300PC (Mount plate + Car
connecting pack + Car battery cord)
•Car battery cord with car connecting pack
DCC-E26CP
Refer to the instruction manual of each
accessory for details.

When you use the CPM-300PC mount

kit/CPM-300P mount plate

Attach the car mount adaptor supplied to the
CPM-300PC/300P before installing the
player.
Notes
•Do not put the player on the dashboard.
•Do not leave the player in a car parked under
sunlight.
•Use a Sony car connecting pack for reducing
noise.
•Use only the car battery cord listed in the
recommended accessories. If you use any other
car battery cord, smoke, fire or malfunction
may occur.

Switched ignition function

(when using the car battery cord)

With this feature, your player stops
automatically when you turn off the engine of
the car. (This function is not possible with
some cars depending on the model.)

Using the remote control

For the customers supplied with the
remote control:
You can use the remote control as the wired
remote control.
* Automatic Music Sensor
** When you are not using the remote control,
slide HOLD in the direction of the arrow to
prevent any accidental operations.
To unlock, slide HOLD back.
Note
•Use only the supplied remote control. You
cannot operate this player with the remote
control supplied with other models.
Earphones
Remote control
Polarity of the plug
Lens

Using dry batteries

1Open the lid of the battery compartment.
2Insert two LR6 (size AA) alkaline
batteries by matching the and to the
diagram inside the battery compartment
and close the lid.
Note
•Do not use manganese batteries for this player.

To take out the dry batteries

Pull the side of the battery as shown.

When to replace the dry batteries

When the battery becomes weak,
indication appears in the display. If the “Lo
batt” appears in the display, replace all the
batteries with new ones, because the batteries
are used up.
Notes
•Do not charge the dry batteries.
•Do not mix new batteries with old ones.
•Do not use different types of batteries together.
•When the batteries are not to be used for a long
time, remove them.
•If the battery leakage occurs, wipe off any
deposit in the battery compartment, and install
new batteries.

Battery life (approx. hours)(EIAJ*)

When using ESP function

off on

BP-DM20 7 6

(charged for about

3.5 hours**)

Two alkaline batteries 14 12

LR6SG

BP-DM10 3.5 3

(charged for about

2 hours**)

*Measured value by the standard of EIAJ
(Electronic Industries Association of Japan)
(When the unit is used on a flat and stable place)
**Charging time varies depending on how the
rechargeable battery is used.

How to attach the battery

compartment lid

If the battery compartment lid is detached by
an accidental drop, excessive force, etc., attach
it as illustrated in the numbered order.
(rear)

zAdditional Information

Precautions

On safety

•Should any solid objects or liquid fall into the
unit, unplug it and have it checked by qualified
personnel before operating it any further.
•Do not put any foreign objects in the DC IN
4.5 V (external power input) jack.

On power sources

•When you are not using the player for a long
time, disconnect all power sources from the
player.
•The nameplate indicating operating voltage,
power consumption, etc. is located at the
bottom of the AC power adaptor (for EA3 only.)

On the AC power adaptor

•Use only the supplied AC power adaptor. If
your player is not supplied with it, use AC-
E45HG AC power adaptor. Do not use any
other AC power adaptor.
•To unplug the AC power adaptor from the wall
outlet, grasp the adaptor itself, do not pull its
cord.

On dry and rechargeable batteries

•Do not throw the batteries into fire.
•Do not carry the rechargeable battery with coins
or other metallic objects. It can generate heat if
the positive and negative terminals of the
battery are accidentally contacted by a metallic
object.
For the customers having purchased the
world model
Certain countries may regulate disposal of the
battery used to power this product.
Please consult with your local authority.

On the player

•Keep the lens of the player clean and do not
touch it. If you do so, the lens may be damaged
and the player will not operate properly.
•Do not put any heavy object on top of the
player. The unit and the CD may be damaged.
•Do not leave the player in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or sand, moisture, rain,
mechanical shock, unleveled surface, or in a car
with its windows closed.
•If the player causes interference to radio or
television reception, turn off the player or move
it away from the radio or television.
•Do not wrap the player in a cloth or blanket
during use as it may cause malfunction or
serious accidents.

On headphones/earphones

Road safety
Do not use headphones/earphones while
driving, cycling, or operating any motorized
vehicle. It may create a traffic hazard and is
illegal in some areas. It can also be potentially
dangerous to play your headsets at high volume
while walking, especially at pedestrian crossings.
You should exercise extreme caution or
discontinue use in potentially hazardous
situations.
Preventing hearing damage
Avoid using headphones/earphones at high
volume. Hearing experts advise against
continuous, loud and extended play. If you
experience a ringing in your ears, reduce volume
or discontinue use.
Caring for others
Keep the volume at a moderate level. This will
allow you to hear outside sounds and to be
considerate to the people around you.

Maintenance

To clean the lens

Clean the lens with a lens cleaning kit KK-DM1.

To clean the casing

Use a soft cloth slightly moistened in water or a
mild detergent solution. Do not use alcohol,
benzine or thinner.

Troubleshooting

Should any problem persist after you have made
these checks, consult your nearest Sony dealer.

The CD does not play or “no dlSC

appears in the display though a CD

is placed in the unit.

mThe CD is dirty or defective.
mInsert the CD with the label side up.
mMoisture condensation has occurred.
Leave the unit aside for several hours until
the moisture evaporates.
mThe lens is dirty.
mClose the lid of the unit and the battery
compartment firmly.
mMake sure the batteries are inserted
correctly.
mConnect the AC power adaptor to a wall
outlet securely.

When you press ^, “00” appears in

the display for a moment, and

disappears. The CD does not play.

mRechargeable battery or dry batteries are
used up. Charge the rechargeable battery
or replace dry batteries with new ones.

No sound, or noise is heard.

mConnect the plugs firmly.
mPlugs are dirty. Clean the plugs with a dry
soft cloth periodically.

Hl dc ln” appears in the display.

mUse only the supplied AC power adaptor
or recommended AC power adaptor AC-
E45HG (not supplied).

Hold” appears in the display when

you press a button.

mThe buttons are locked. Slide HOLD back.

Lo batt

appears in the display

when you press a button.

mThe rechargeable battery is used up
completely. Connect the AC power
adaptor and charge the battery.
mThe dry batteries are used up. Replace
them with new ones.

The battery life is short.

mManganese batteries are used. Use alkaline
batteries.
mReplace the batteries with new ones.

The volume is limited to a certain

level even if you attempt to turn it

up.

mAVLS selector is set to LIMIT. Set it to
NORM.

Specifications

CD player

System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output
is the value measured at a distance of 200 mm
from the objective lens surface on the optical
pick-up block with 7 mm aperture. )
Error correction
Sony Super Strategy Cross Interleave Reed
Solomon Code
D-A conversion
1-bit quartz time-axis control
Frequency response
20 - 20,000 Hz +1 dB (measured by EIAJ CP-
307)
Output (at 4.5 V input level)
Headphones (stereo minijack)
15 mW + 15 mW at 16 ohms
Line output (stereo minijack)
Output level 0.7 V rms at 47 kilohms
Recommended load impedance over 10
kilohms

General

Power requirements
For the area code of the model you purchased,
check the upper left side of the bar code on the
package.
•Sony BP-DM10 Rechargeable battery:
2.4 V DC, Ni-Cd, 650mAh
Sony BP-DM20 Rechargeable battery:
2.4 V DC, Ni-MH, 1,200 mAh
•Two LR6 (size AA) batteries: 3 V DC
•AC power adaptor (DC IN 4.5 V jack):
U2/CA2/E92 model: 120 V, 60 Hz
CED/CEF/CEX/EE1/E13/CE7/CEW/
G6 model: 220 - 230 V, 50/60 Hz
CEK model: 230 - 240 V, 50 Hz
EA3 model: 110 - 240 V, 50/60 Hz
AU2 model: 240 V, 50 Hz
JE.W/E33 model: 100 - 240 V, 50/60 Hz
HK2 model: 220 V, 50/60 Hz
CN2/AR1 model: 220 V, 50 Hz
•Sony CPM-300P mount plate for use on car
battery: 4.5 V DC
Dimensions (w/h/d) (without projecting parts
and controls)
Approx. 129 × 28 × 146 mm
(5 18× 1 18 × 5 34 in.)
Mass (without rechargeable battery)
Approx. 220 g (7.8 oz)
Operating temperature
5°C - 35°C (41°F - 95°F)

Supplied accessories

For the area code of the model you purchased,
check the upper left side of the bar code on the
package.
D-E400
AC power adaptor (1)
Rechargeable battery (1)
Earphones with remote control (1)
AC plug adaptor (1)
D-E400AN
Earphones (1)
D-E400HR
Earphones with remote control (1)
D-E401
AC power adaptor (1)
Headphones (1)*1
Earphones (1)*2
Connecting cord (Phono plug × 2 stereo
miniplug) (1)*3
AC plug adaptor (1)*4
*1Supplied with U2 model
*2Not supplied with U2 model
*3Not supplied with CED, CEX, CEK, AR1
and EE1 models
*4Supplied with E33, E13 and EA3 models
D-E401SR
AC power adaptor (1)
Headphones (1)
Active speaker system (1)
AC plug adaptor (1)*
* Supplied with E13 model
D-E403
AC power adaptor (1)
Earphones (1)
Rechargeable battery (1)
AC plug adaptor (1)*
*Supplied with E33, E13 and EA3 models
D-E405
AC power adaptor (1)
Headphones with remote control (1)*1
Earphones with remote control(1)*2
Rechargeable battery (1)
Connecting cord (Phono plug × 2 stereo
miniplug) (1)*1
AC plug adaptor (1)*3
*1 Supplied with U2 model
*2 Not supplied with U2 model
*3 Supplied with E13 model
-2
LINE IN or
REC IN Stereo system,
cassette recorder,
radio cassette
recorder, etc.
Right (red)
LINE OUT
NORM LIMIT
AVLS
(AUTO VOLUME LIMITER SYSTEM)
RESUMEOFF ON
Left (white)
Connecting cord
RK-G129HG
(rear)
(rear)
D-E406CK
AC power adaptor (1)
Headphones (1)*1
Earphones (1)*2
Connecting cord (Phono plug × 2 stereo
miniplug) (1)*3
Car battery cord (1)
Car connecting pack (1)
Velcro tape (2)
Spare fuse (1)
Spiral tube (1)
AC plug adaptor (1)*4
*1 Supplied with U2 model
*2 Not supplied with U2 model
*3 Not supplied with CED, CEX, G6 and U2
models
*4 Supplied with E33, E13 and EA3 models
D-E409CK
AC power adaptor (1)
Rechargeable battery (1)
Headphones with remote control (1)
Car battery cord (1)
Car connecting pack (1)
Velcro tape (2)
Spare fuse (1)
Spiral tube (1)
Design and specifications are subject to change
without notice.
For US customers
AC power adaptor supplied is not intended to be
serviced. Should the AC power adaptor cease to
function in its intended manner, during the
warranty period, the adaptor should be returned
to your nearest Sony Service Center or Sony
Authorized Repair Center for replacement, or
after warranty period, it should be discarded.

Recommended accessories

Mount plate CPM-300P
Mount kit CPM-450PC*1
Mount kit CPM-300PC
Car connecting pack CPA-9
Car battery cord with car connecting pack
DCC-E26CP
Car battery cord DCC-E245
Active speaker system SRS-A15, SRS-A35,
SRS-A71, SRS-T1
Rechargeable battery BP-DM10, BP-DM20
Connecting cord RK-G129HG, RK-G136HG
AC power adaptor AC-E45HG
Stereo headphones MDR-A44L, MDR-301LP,
MDR-E848LP, MDR-35*2
*1Sold in Japan only
*2When connecting optional headphones to
the supplied remote control, use only
headphones with stereo mini plugs. You
cannot use headphones with micro plugs.
Your dealer may not handle some of the above
listed accessories. Please ask the dealer for
detailed information about the accessories in your
country.
HOLD**
VOL (volume)
p (stop)
((play)•
+ (AMS*/
search)
= (AMS*/
search)