仕様

一般

 

 

 

 

 

電源

 

+12 V DC400 mA (装着した機器より供給)
動作温度

 

5℃~40

 

 

 

保存温度

 

20℃~+60

 

 

保存湿度

 

20%90% (相対湿度、結露なし)

 

外形寸法

 

134×26.2×112.8 mm(幅 /高さ/ 奥行き)

 

 

(端子部および取り付けネジ部含まず)

質量

 

0.16 kg

 

 

 

出力端子

 

 

 

 

 

VIDEO

 

BNC型(1

 

 

 

 

 

コンポジット:1.0 Vp-p75Ω

 

 

SDI

 

BNC型(1

 

 

 

 

 

SMPTE259M75Ω

 

 

MONITOR

D-sub 9ピン(1

 

 

出力レベル

コンポジット:1.0 Vp-p75Ω

 

 

 

 

コンポーネント

Y1.0 Vp-p

 

 

 

 

Pb/Pr0.7 Vp-p75Ω

 

 

R/G/B1.0 Vp-p (Sync付き)、75Ω

 

 

 

Sビデオ Y1.0 Vp-p

 

 

 

 

C:コンポジットのクロマ信号と同レベル

 

 

SYNC0.3 Vp-p75Ω

 

 

ピン配列

5

1

 

 

 

 

9

6

 

 

 

 

 

 

 

 

ピン

信号

ピン

信号

ピン

信号

 

 

 

 

 

 

1

GND

4

G/Y

7

SYNC

 

 

 

 

 

 

2

GND

5

B/Pb

8

GND

 

 

 

 

 

3

R/Pr

6

Composite/Y 9

/C

 

 

 

 

 

 

付属品オペレーションマニュアル(1

本機の仕様および外観は、改良のため予告なく変更することがありますが、ご 了承ください。

お使いになる前に、必ず動作確認を行ってください。故障その他に伴う営 業上の機会損失等は保証期間中および保証期間経過後にかかわらず、補 償はいたしかねますのでご了承ください。

English

Overview

The HFBK-SD1 is an optional board designed to be installed in the following apparatuses:

HFU-X310 HD Camera Interface UnitBRC-H700 HD 3CCD Color Video CameraBRU-H700 HD Optical Multiplex Unit

The board down-converts images from the color video camera connected to the apparatus that accommodates the board and supplies them as SD-SDI and analog signals. You can select the output signal aspect ratio from among 16:9 letterbox, 4:3 edge crop, and squeeze. As analog outputs, component, composite and S video signals are available.

When the board is installed in an HFU-X310 that supports embedded audio and time code, the embedded audio and time code of HD-SDI signal supplied to the HFU-X310 are embedded in the SD-SDI output signal.

NoteThe time code is output to the following lines (fixed).
When video signal is

When video signal is

NTSC (59.94i)PAL (50i)

 

 

LTC: Line 13

LTC: Line 9

 

 

VITC1: Lines 12 and 14VITC1: Lines 8 and 10

 

 

VITC2: Lines 275 and 277VITC2: Lines 321 and 323

 

 

Locations and Functions of Parts

MONITOR

VIDEO SDI

HFBK-SD1

 

1 MONITOR connector4 SDI connector
3 VIDEO connector

 

2DIP switches (behind the cover)
1MONITOR connector (D-sub 9-pin)

For analog video output. The configuration of the output signal can be specified by setting the DIP switches.

2DIP switches
To configure the output signals.

Note

Turn the apparatus that accommodates the board off before changing the DIP switch settings.

Switch 1 (Sync/Setup)

When RGB output is selected for the MONITOR connector with Switch 3, this switch specifies whether to add a sync signal to the output signals:

Upper (Add Sync): To add a sync signal (factory setting)Lower (No Sync): Not to add any sync

When YPbPr output is selected for the MONITOR connector with Switch 3, this switch specifies whether to add 7.5% Setup to the output signals:

Upper (No Setup): Not to add any Setup (factory setting)
Lower (Add Setup): To add Setup
NotesSetup can be added only when the video signal is NTSC (59.94i).Setup is added to both the MONITOR and VIDEO connector outputs.

When this board is mounted in a BRC-H700 or BRU-H700, Setup adding is allowed only when the BRC-H700 or BRU-H700 is in a version that can control the Setup adding function of this board.

For information of the version, please ask your Sony representative.
Switch 2 (Sync on G)

Specifies whether to add a sync signal to each of the R, G, and B signals or only to the G signal when “RGB” is selected with Switch 3 and “Add Sync” is selected with Switch 1 for the MONITOR connector output:

Upper (Sync on ALL): To output each of the R, G, and B signals with a sync signal added (factory setting)

Lower (Sync on G): To output the G signal with a sync signal added
Switch 3 (RGB/YPbPr)

Selects the component output from the MONITOR connector: Upper (YPbPr): To output component signals (factory setting) Lower (RGB): To output RGB signals

Switch 4 (Composite/S Video)
Specifies the signal to be supplied from pin 6 of the MONITOR connector:Upper (Composite): To output analog composite signals (factory setting)Lower (Y): To output the Y signal of S video. The C signal is output from pin 9
Switch 5 (16:9/4:3)
Selects the aspect ratio of the output signal:

Upper (16:9): To select 16:9 letterbox (factory setting) (Switch 6 becomes invalid.)

Lower (4:3): To select 4:3. Select edge crop or squeeze with Switch 6
Switch 6 (Crop/Squeeze)

Valid when 4:3 aspect ratio is selected with Switch 5: Upper (Crop): To output edge crop (factory setting) Lower (Squeeze): To output squeeze

Switch 7 (Delay)
Specifies whether to delay video output with respect to a sync signal:Upper (No Delay): Not to delay (factory setting)Lower (Delay): To delay 89 or 90 lines (HD)
Switch 8 (89H/90H)
Selects the phase difference to delay when “Delay” is selected with Switch 7:Upper (89H): 89 lines (HD) (factory setting)
Lower (90H): 90 lines (HD)

Note

Switches 7 and 8 are valid only when the board is installed in an HFU-X310 of a version that supports the Delay function.

For details on the functions of Switches 7 and 8, refer to the Operation Manual of the HFU-X310.

3VIDEO (analog composite) connector (BNC type)

Outputs analog composite signals for checking images. The aspect ratio can be selected with the DIP switches.

4SDI connector (BNC type)

Outputs down-converted SD-SDI signals. The aspect ratio can be selected with the DIP switches.

Specifications

General

 

 

 

 

Power requirements+12 V DC, 400 mA (supplied from the

 

 

apparatus that accommodates the board)
Operating temperature

 

 

 

 

 

5°C to 40°C (41°F to 104°F)
Storage temperature –20°C to +60°C (–4°F to +140°F)
Storage humidity20% to 90% (relative, no condensation)
Dimensions134 26.2 112.8 mm (w/h/d)

 

 

(53/8 11/16 41/2 inches)

 

 

 

not including projecting parts
Mass

 

Approx. 0.16 kg (6 oz)

 

Outputs

 

 

 

 

VIDEOBNC type (1)

 

 

 

 

Composite: 1.0 Vp-p, 75
SDI

 

BNC type (1), SMPTE259M, 75
MONITORD-sub 9-pin (1)

 

Output level

Composite: 1.0 Vp-p, 75

 

 

Component Y: 1.0 Vp-p

 

 

 

 

 

Pb/Pr: 0.7 Vp-p, 75

 

 

R/G/B: 1.0 Vp-p (with Sync), 75

 

 

S video Y: 1.0 Vp-p

 

 

 

 

C: Same level as with the chroma

 

 

 

 

signal of composite

 

 

Sync: 0.3 Vp-p, 75

 

Pin assignment

 

5

1

 

 

 

 

9

6

 

 

 

 

 

 

 

PinSignal

Pin

Signal

Pin

Signal

 

 

 

 

 

 

1

GND

4

G/Y

7

SYNC

 

 

 

 

 

 

2

GND

5

B/Pb

8

GND

3

R/Pr

6

Composite/Y 9

–/C

 

 

 

 

 

 

Supplied accessory
Operation Manual (1)Design and specifications are subject to change without notice.
Note
Always verify that the unit is operating properly before use.

SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.