Manuals / Brands / Home Audio / Home Theater System / Sony / Home Audio / Home Theater System

Sony HT-SF1100, HT-SS1100 Specifications, 57GB, General, Area code, Area code, Area code, HT-SF1100only, HT-SS1100only, FM tuner section, AM tuner section, Amplifier section

1 60

Download 60 pages, 835.33 Kb

Specifications

Amplifier sectionHT-SF1100 only

Power Output1)

Stereo mode (rated) 70 W + 70 W

(4 ohms at 1 kHz, THD 1%)

Surround mode (reference)

RMS Output FRONT2): 143 W/ch (With SS-MSP2000) CENTER2): 143 W (With SS-CNP2000) SUR2): 143 W/ch (With SS-SRP2000) SUBWOOFER2): 285 W (With SS-WP2000)

HT-SS1100 only

Power Output1)

Stereo mode (rated) 70 W + 70 W

(4 ohms at 1 kHz, THD 1%)

Surround mode (reference)

RMS Output FRONT2): 143 W/ch (With SS-MSP1100) CENTER2): 143 W (With SS-CNP1100) SUR2): 143 W/ch (With SS-SRP1100) SUBWOOFER2): 285 W (With SS-WP1100)

1)Measured under the following conditions:

Area code	Power requirements
CEL, CEK	230 V AC, 50 Hz

2)Reference power output for front, center, surround speakers and subwoofer. Depending on the sound field settings and the source, there may be no sound output.

Inputs
Analog	Sensitivity: 1 V/50 kohms
Digital (Coaxial)	Impedance: 75 ohms
Tone
Gain levels	±6 dB, 1 dB step

Reproduction frequency range:

28 – 20,000 Hz

FM tuner section

Tuning range	87.5 - 108.0 MHz
Antenna	FM wire antenna
Antenna terminals	75 ohms, unbalanced

Intermediate frequency

10.7 MHz

AM tuner section

Tuning range

Models of area code CEL, CEK With 9-kHz tuning scale:

531 – 1,602 kHz

AntennaLoop antenna Intermediate frequency

450 kHz

General

Power requirements

	Area code	Power requirements
	CEL, CEK	230 V AC, 50/60 Hz
	Power output (DIGITAL MEDIA PORT)
	Power output (DIGITAL MEDIA PORT)				Additional
	DC OUT:	5 V, 700 mA			Additional
	DC OUT:	5 V, 700 mA
	Power consumption

	Area code	Power consumption			Information

	CEL, CEK	0.3 W
	CEL, CEK	110 W
	Power consumption (during standby mode)
	Dimensions (w/h/d) (Approx.)
		430 × 66.5 × 335 mm
		including projecting parts
		and controls
	Mass (Approx.)	3.6 kg

continued

57GB

Contents

Page WARNING For customers in Europe About This Manual The HT-SF1100consists of: • Receiver • Speaker systema) – Front speakers Table of Contents Description and location of parts About the indicators on the display qd qs qa q; ALFE Lights up when the disc being played back contains an LFE Rear panel AANTENNA section BDIGITAL INPUT/OUTPUT section CSPEAKERS section DAUDIO INPUT section Remote commander RM-AAU017 AV ?/1 (on/standby) off C Input D MOVIE Press to select sound fields (MOVIE) MUSIC (MUSIC) O RETURN EXIT O – exit the menu while the satellite tuner or Blu-ray disc player is displayed on 1: Installing speakers Installing the speakers on a flat surface Example of HT-SS1100front speaker Installing the speakers on the wall HT-SS1100only Installing the speakers on the speaker stand 3 Hang the speakers on the screws Example of installing the speakers on the wall 13GB 2: Connecting speakers ASpeaker cord (supplied)a) 3:Connecting the audio/ video components AAudio cord (not supplied) CCoaxial digital cord (supplied) •Do not bend or tie optical digital cords Tips •All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling frequencies –turn off or mute the TV’s volume ACoaxial digital cord (supplied) BHDMI cable (not supplied) COptical digital cord (not supplied) Notes on HDMI connections –connect the digital audio jacks on the playback component to the receiver –turn off or mute the TV’s volume •The multi/stereo area audio signals of a Super Audio CD are not output 19GB 4: Connecting the antennas 5:Preparing the receiver and the remote 6:Calibrating the appropriate settings automatically Example: HT-SS1100 2 Set up the optimizer microphone Performing Auto Calibration Press AMP MENU, then press AUTO CAL The measurement process will take a few minutes to complete The table below shows the display when measurement starts Error and warning codes Error codes tENTER To rectify the error 1Record down the error code Warning codes To change the settings manually 1Record down the warning code 4Follow the solution provided in the “Warning codes and solutions” below Warning codes and solutions 7:Adjusting the speaker levels and balance Selecting a component Listening/Watching a component Watching a DVD Turn on the TV and DVD player Press DVD You can also use INPUT SELECTOR on this receiver to select “DVD” Navigating through menus Overview of the menus Menu Parameters Settings Initial setting 32GB Adjusting the level Adjusting the tone Settings for the surround sound Settings for the tuner Settings for the audio Settings for the system xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) Also, the center speaker cannot be set more than For example, setting the center speaker distance xSUR PL Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Decoding A.F.D. mode Multi channel Effect Selecting a preprogrammed sound field 40GB Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes 41GB Using only the front speakers and sub woofer Listening to FM/AM radio 1 Press TUNER repeatedly to select the FM or AM band 2 Press TUNING + or TUNING – In case of poor FM stereo reception Direct tuning 2 Press D.TUNING 3 Press the numeric buttons to enter the frequency 4 Press ENTER If you cannot tune in a station Presetting radio stations Tuning to preset stations 2 Press PRESET + or PRESET – repeatedly to select the preset station you want Each time you press the button, you can select a preset station as follows: Using the controls on the receiver Using the Radio Data System (RDS) (Models of area code CEL, CEK only) •RDS is operable only for FM stations Receiving RDS broadcasts 46GB Displaying RDS information While receiving an RDS station, press DISPLAY repeatedly Description of program types Program type Description Enjoying the DIGITAL MEDIA PORT AVideo cord (not supplied) To detach the DIGITAL MEDIA PORT adapter from DMPORT jack Press and hold both sides of the connector and then pull out the connector Listening to a connected component through DMPORT connection 1 Press DMPORT 2 Start playback of the connected component 49GB Operations Other Using the Sleep Timer Changing button assignments Glossary Precautions On placement If color irregularity is observed again If howling occurs On cleaning Troubleshooting The surround effect cannot be obtained •Make sure you have selected a sound field with MOVIE or MUSIC button Dolby Digital or DTS multi channel sound is not reproduced Video There is no picture or an unclear picture appears on the TV screen or monitor The RDS information that you want does not appear.a) Remote control The remote does not function •Point the remote at the remote sensor on the receiver •Remove any obstacles in the path between the remote and the receiver Specifications Speaker section •Front speakers (SS-MSP2000) •Center speaker (SS-CNP2000) •Surround speakers (SS-SRP2000) Subwoofer (SS-WP2000) Supplied speakers Supplied accessories For details on the area code of the component you are using, see page Design and specifications are subject to change without notice 59GB Index