3-995-884-31(2)

FM/AM

2 Band Radio

Operating Instructions
Mode d‘emploi
Owner’s Record

The model number and the serial number are located on the rear.

Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. ICF-9740W

Serial No.

ICF-9740W

Sony Corporation 1980 Printed in Taiwan R. O. C

English

•Before operating the set, please read this manual thoroughly. •This manual should be retained for future reference.

WARNING
To prevent fire or shock hazard, do not expose the set to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

For the Customers in Canada

CAUTION:

Location and Function of Controls

Perform the following steps in sequence for reception.

Dial ScaleFM External Antenna Terminals [FM EXT ANT] (rear)

See “Antennas”.

Recording Jack [†] (Canadian model only) (rear)

For recording radio programs with a tape recorder. Connect this jack to the microphone input jack of your tape recorder with a suitable cord. In the case of a Sony tape recorder, use the Sony Connecting Cord RK-69A (optional).

The volume or tone control setting of the radio has no effect on the recording.

4 TUNING Knob

Turn to select the frequency of the desired station, as marked on the Dial Scale.

3 BAND SELECT Switch

Choose the desired band: FM or AM.

LOUDNESS Switch

Normally set the switch to OFF.

When listening to a program at a low volume, set the switch to ON. This will compensate for our reduced sensitivity to bass and treble at a low volume. The effect of this control gradually decreases as the volume is increased.

5 TONE Control

Turn towards HIGH for more treble, and towards LOW for less treble.

2 Power/Volume Control [POWER/VOL]

Turn clockwise and the power will be on with a slight click.

Turn it further for more volume. After using, set it to OFF.

1 AC Power Cord

Connect to a wall outlet (120V AC).

This instruction manual covers the USA and Canadian models of the ICF-9740W table radio. Their performance and specifications are identical except that the Canadian model has a recording jack.

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Antennas

Precautions

•Operate the set only on 120 V AC, 60 Hz.

•The nameplate indicating operating voltage, power consumption, etc. is located on the rear exterior.

•Unplug the set from the wall outlet when it is not to be used for an extended period of time. To disconnect the cord, pull it out by grasping the plug. Never pull it by the cord.

•Do not install the set in a location near heat sources such as radiators or airducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration, or shock.

•Allow adequate air circulation to prevent internal heat build-up. Do not place the set on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes.

Specifications

Frequency range

FM 87.5 - 108 MHz (3.42 - 2.78m)

 

AM 530 - 1,605 kHz

(566 - 187 m)

Antennas

FM: AC power cord antenna

 

External antenna terminals (75 ohms)

 

AM: Built-in ferrite bar antenna

Speaker

Approx. 16 cm (6 3⁄8

inches) dia.

Power output

2W (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz

 

 

 

Dimensions

Approx. 330 x 232 x 136 mm (w/h/d)

 

(13 x 9 1⁄

4

x

5 3⁄ inches)

 

 

 

8

 

Incl. projecting parts and controls

Mass

Approx. 2.2kg (4 lb

13 oz)

AM reception: The built-in ferrite bar antenna is used. Since the antenna is directional, rotate the set horizontally for optimum reception, if necessary.

FM reception: Extend the attached AC Power Cord so that the FM sensitivity will be increased, as it has the function of an FM antenna.

FM reception for difficult reception areas

In a steel-frame building, a mountainous area or at a long distance from a transmitter, reception may be unsatisfactory. In that case, connect a commercially available FM external antenna to the FM EXT ANT terminals at the rear as illustrated.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820 - 40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

•Should any liquid or solid object fall into the set, unplug the set and have the set checked by qualified personnel before operating it any further.

•When the cabinet becomes soiled, clean it with a soft cloth dampened with a mild detergent solution. Never use abrasive cleansers or chemical solvents, as they may mar the cabinet.

•When an external antenna is used, disconnect it from the antenna terminals of the set during a lightning storm, unless the installation incorporates a suitable lightning arrestor.

If you have any question or problem concerning your set that is not covered in this manual, please consult your nearest Sony dealer.

Design and specifications subject to change without notice.

FM EXT ANT

feeder wireor braid coaxial cablecenter conductor