| AC power cord | Cord clamp |
A | Spacer |
| L (Low) |
| Template |
| Dot | H | L |
Installing the Unit Under a Cabinet
(See Fig. A)The unit can be installed without the spacer.1Mark the position of the 4 holes by using the supplied template. Use a drill to make the holes (size 6.5 mm dia., 9/32 inch). (See Fig. A- )
2When the cabinet door overhangs the shelf and obstructs the unit, you can adjust the unit/shelf height.
First set the L mark to the dot which becomes the lowest position, then you can adjust the height in 4 steps (H••L) by turning the spacer counterclockwise. (See Fig. A- )
3Install the unit with the supplied mountingscrews. (See Fig. A- )Cautions•Since the unit is very heavy, be careful when installing the unit.•You need two people to install the unit.•Be careful with the tools you use when installing the unit.•Be sure that the cabinet is sturdy enough to support the weight of the unit.•To reduce the risk of fire, do not place any heating or cooking appliance beneath this unit.
•Install the unit so that its AC power cord can be connected directly to a wall outlet. Do not use a converter or extension cord.
•Be sure that the AC power cord has no slack when using the unit, since the cord acts as an FM wire antenna. If the AC power cord has some slack, wind it up to the cord hook until the cord has no slack.
•The unit has a
•Install the unit as far as possible from a source of noise. (for example, refrigerator, microwave oven, fluorescent lamp, etc.)
•This unit is not waterproof. The unit should be installed where it will not be exposed to splashing water, which could damage the unit.
•To reduce the risk of fire or electric shock, do not touch the AC power cord with wet hands.
•Never place objects between the top of the unit and the bottom of the cabinet. This could cause the unit to fall.
Setting the Clock
1Plug in the clock radio.The display will flash “AM 12:00”.2Press CLOCK for a few seconds.You will hear a beep and the hour will start to flash in the display.
3Press TUNE/TRACK/TIME SET + or
– until the correct hour appears in the display.4Press CLOCK once. The minute will flash.
5Repeat steps 3 and 4 to set the minute.After setting the minute, press CLOCK to start the counting of the seconds, and you will hear two short beeps.
•To set the current time rapidly, hold downTUNE/TRACK/TIME SET + or•In step 5, when you press CLOCK after the minute setting to activate the clock, the seconds start counting from zero.
To change the display to the daylight saving time (summer time) indicationPress D.S.T.•SUMMER T..
“
” is displayed and the time indication changes to summer time.To deactivate the summer time function, press D.S.T.•SUMMER T. again.Playing a CD
An 8 cmTo | Press |
| Pause | CD u |
| Resume play after | CD u again |
| pause |
|
|
|
| Locate the beginning | .** |
| of the current |
|
| track (AMS*) |
|
|
|
| Locate the next | >** |
| track (AMS) |
|
|
|
| Go back at high speed | Hold down .** |
|
|
| Go forward at high | Hold down >** |
| speed |
|
|
|
| Locate the previous | . repeatedly** |
track (AMS) |
|
|
|
| Locate the succeeding | > repeatedly** |
track (AMS) |
|
|
|
| Stop play | x |
|
|
A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed.
Music discs encoded with copyright protection technologiesThis product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.
To handle compact discsCorrectHandle the disc by its edge.IncorrectDo not touch the surface.Do not stick paper or tape nor write anything on the surface.Notes•If you press CD u when there is no disc in the CD compartment, “00” flashes for a few seconds on the display and the unit turns off automatically.
•Discs with
Press CD PLAY MODE.
Each press changes the play mode as follows:DisplayPlayindication mode| none | (normal play) < |
|
| ||
| All the tracks are played once. | ||
| m | |
| “REP 1” | (single repeat) | |
| A single track is played repeatedly. | ||
| m | |
| “REP ALL” | (all repeat) | |
| All the tracks are played repeatedly. | ||
| m | |
| “SHUFFLE” | (shuffle play) | |
m
“SHUFFLE REP” (shuffle repeat)All the tracks are played repeatedly in random order.Playing the Radio
Manual Tuning1Press RADIO ON•BAND to turn on the radio.“RADIO” appears in the display.The display shows the band and frequency for a few seconds and then changes back to the current time.
2Press RADIO ON•BAND repeatedly to select the desired band.Each press changes the band as follows:*When using FM1 or FM2 preset mode, you may listen to the radio on either mode(See “Preset Tuning”).3Use TUNE/TRACK/TIME SET + or – to tune in to the desired station.
The FM channel step is set to 0.1 MHz and the AM channel step is set to 10 kHz.Two short beeps sound when the minimum frequency of each band is received during tuning.
4Adjust volume using VOLUME.
•To turn off the radio, pressOFF/ALARM RESET x.•To improve radio receptionFM: Extend the AC power cord fully to improve FM reception.AM: When installing the unit, rotate the unit horizontally for optimum reception and then install the unit. A ferrite bar antenna is built into the unit.
•To check the station being received, pressRADIO ON • BAND lightly. The display shows the band and frequency for a few seconds and then changes back to the current time.
You can preset 10 stations in FM (5 stations in FM1, 5 stations in FM2) and 5 stations in AM.
Presetting a StationExample: To preset FM90 MHz onto preset button 2 for FM2.1Press RADIO ON•BAND to turn on the radio.
2Press RADIO ON•BAND to select FM2.3Tune in to the station on FM90 MHz (See “Manual Tuning”).