CLOCK TIME ZONE DST

RADIO

BUZZER

 

 

 

RADIO SLEEP

ON

OFF

 

OFF

 

 

AC power cord

ALARM MODE

 

ALARM RESET

 

 

 

ALARM TIME SET

3Press TIME ZONE repeatedly until the desired number appears.

The display returns to the clock about 4 seconds after the operation is complete.

Note

During the shipment and your first use, a clock error may occur. In this case, refer to “Setting the clock and date” to set the correct time.

Playing the radio

1Press RADIO ON to turn on the radio.2Adjust volume using VOLUME.3Select BAND.4Tune in to a station using TUNING.

To turn off the radio

To doze for a few more minutes

Press SNOOZE/DATE/SLEEP OFF.

The sound turns off but will automatically come on again after about 10 minutes. Each time you press SNOOZE/DATE/SLEEP OFF, the snooze time changes as follows:

The maximum length of the snooze time is 60 minutes.

SNOOZE / DATE / SLEEP OFF

 

SL

 

S

EEP

 

 

 

NO

 

 

OZ

 

 

E /

 

 

DA

 

 

TE

 

 

/S

 

 

LE

 

DST

EP

OF

 

F

AM

ALARM

 

PM

 

 

PULL

 

BAND FM

AM

VOL

TUNING

 

When daylight saving time (summer time) begins

The following models employ the Automatic Daylight Saving Time/Summer Time adjustment. The DST indicator in the display appears in the display at the beginning of the daylight saving time (summer time), and disappears at the end of it.

•Daylight saving time begins at: 2:00 AM on the second Sunday of March.

•Standard time begins at: 2:00 AM on the first Sunday of November.

To cancel the Automatic DST/ Summer Time adjustment and to set DST display manually

The Automatic DST/Summer Time adjustment can be cancelled.

Press and hold DST for more than 3 seconds while the clock is displayed.

A beep sounds, and “Aut tOFF” appears in the

Press RADIO OFF/ALARM RESET.

Improving the reception

FM:

The AC power cord functions as an FM antenna. Extend the AC power cord fully to increase reception sensitivity.

AM:

Rotate the unit horizontally for optimum reception. A ferrite bar AM antenna is built-in to the unit.

The display shows the snooze time for about

4 seconds and returns to show the current time. When you press SNOOZE/DATE/SLEEP OFF after the current time appears, the snooze time starts from 10 minutes again.

To stop the Alarm

Press RADIO OFF/ALARM RESET to

turn off the alarm.

The alarm will come on again at the same time the next day.

If RADIO OFF/ALARM RESET is not pressed, the alarm sounds continuously for about 60 minutes, and then it will be stop automatically.

To deactivate the Alarm

Turn ALARM MODE to OFF.

ALARM indicator disappears from the display.

Note on alarm in the event of a power interruption

* There is a tactile dot beside

Battery compartmentVOLUME to show the direction to turn up the volume.

BAND

AM FM

TUNINGVOL

A

12 3

display to show that the Automatic DST/Summer Time adjustment is cancelled. The display returns to the clock.

Notes

•The change timing of Automatic DST/Summer Time adjustment employed by the unit (see above) is subjected to variation by circumstances and the law in each country/region. In such a case, cancel the Automatic DST/Summer Time adjustment and set DST display manually as necessary. The customer who lives in the country/region that has not introduced the daylight saving time (summer time) must cancel Automatic DST/Summer Time adjustment before using the set.

•To activate the Automatic DST/Summer Time adjustment again, press and hold DST for more than 3 seconds. A beep sounds, and “Aut tOn” appears in the display to show that the Automatic DST/ Summer Time adjustment is activated. The display returns to the clock.

•To change the display to the daylight saving time (summer time) manually, see “To change the display to the daylight saving time (summer time) indication.”

Setting the clock and date

Do not operate the unit over a steel desk or metal surface, as this may lead to interference of reception.

Setting the alarm

The alarm function can be select from two alarm sounds, RADIO or BUZZER.

Notes

•Before setting the alarm, make sure to set the clock (see “Setting the clock and date”).

•The factory setting alarm time is “PM 12:00”.

•To set the radio alarm, first tune in to a station and adjust the volume (see “Playing the radio”).

To set the alarm time

1 Set ALARM MODE to the desired alarm

sound (RADIO or BUZZER).

The alarm time appears for a few seconds, and

If the alarm set time comes in the event of a power interruption or a power interruption occurs while the alarm is sounding, the display will turn off and the alarm will not sound, and the alarm status will be as follows. If power returns within 60 minutes from the alarm set time, the alarm will sound. If the power interruption occurred while the Snooze function was operating, the snooze function will continue. If the snooze time had passed when the power interruption occurred, the alarm will sound after power returns.

In this status, if the Eindicator does not light up, RADIO OFF/ALARM RESET, SNOOZE buttons and ALARM MODE functions are available. SNOOZE time will be fixed only 10 minutes if the SNOOZE button has been pressed.

Setting the sleep timer

You can fall asleep to the radio using the built-in sleep timer that turns off the radio automatically after a preset duration.

Press SLEEP.

The radio turns on. You can set the sleep timer to durations of 90, 60, 30, or 15 minutes. Each press changes the display as follows:

About the backup battery

To keep good time, as backup power source, this unit has one CR2032 battery inside of the unit in addition to the house current.

The battery keeps the clock in the event of a power interruption.

Knowing when to replace the battery

When the battery becomes weak, “E” indicator appears in the display.

In the event of a power interruption when the battery is weak, current time and alarm functions will be initialized.

Replace the battery with a Sony CR2032 lithium battery. Use of another battery may present a risk of fire or explosion.

Installing and replacing the backup battery

1Keep the AC plug connected to the AC outlet, remove the screw that secures the battery compartment at the bottom of the

unit using a screwdriver, and remove the battery compartment. (See Fig. A-1)2Insert a new battery in the battery compartment with the e side facing up.

To remove the battery from the battery

compartment, push it out from the side marked PUSH. (See Fig. A-2)

3Insert the battery compartment back into theunit and secure it with the screw. (See Fig. A-3)

4When you are replacing the battery, press RADIO ON to turn “E” indicator off in the display.

Note

If you replace the battery, do not disconnect AC plug from AC outlet.

Otherwise, current time and alarm will be initialized.

PUSH

NOTES ON LITHIUM BATTERY

•Dispose of used battery promptly. Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor.

•Wipe the battery with a dry cloth to assure a good contact.

•Be sure to observe the correct polarity when installing the battery.

•Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur.

•Do not expose the battery to excessive heat such as direct sunlight, fire or the like.

Battery Warning

When the unit will be left unplugged for a long time, remove the battery to avoid undue battery discharge and damage to the unit from battery leakage.

Setting the clock for the first time

This unit is preset to the current date and time at the factory, and is powered by the back up battery. All you need to do the first time is just plug it in and select your time zone.

1Plug in the unit.

“month and date” (about 1 second) t“year” (about 1 second) t“the current EST/EDT (Eastern Standard/Daylight Time)” appears in the display.

2Press TIME ZONE.

Area number “2” appears in the display.

If you live in the Eastern Time zone, you do not need to adjust the area setting.

Area number
Time zone

1

Atlantic Standard/Daylight Time

 

 

2

Eastern Standard/Daylight Time

(default)

 

3

Central Standard/Daylight Time

4

Mountain Standard/Daylight Time

 

 

5

Pacific Standard/Daylight Time

 

 

6

Yukon Standard/Daylight Time

 

 

7

Hawaiian Standard/Daylight Time

To change the setting manually, follow the procedure from step 1.

1Press CLOCK for more than 2 seconds.

You will hear a beep and the year will start to flash in the display.

2Press + or – until the correct year appears in the display.3Press CLOCK.4Repeat steps 2 and 3 to set the month, day and time.

After setting the time, two short beeps sound and the clock starts from 0 seconds.

•Pressing and holding + or – changes the year, month or day rapidly.

When setting the current time, time changes rapidly by 1 minute-increments up to 10 minutes, and then by 10 minute-increments.

•While setting the clock, you must perform each step within 65 seconds, or the clock setting mode will be cancelled.

To display the year and date

Press SNOOZE/DATE/SLEEP OFF once

for the date, and within about 3 seconds press it again for the year.

The display shows the date or year for about 3 seconds and then changes back to the current time. If you connect the AC plug to AC outlet while this unit is powered from the backup power source, the current date and time appears in the following order. (It is same as when the unit is powered on after the power failure.)

“month and date” (about 1 second) t“year” (about 1 second) t“current time”

To change the display to the daylight saving time (summer time) indication

Change the daylight saving time (summer time) adjustment setting according to the following procedures if you have cancelled the Automatic DST/ Summer Time adjustment.

Press DST.

DST indicator appears in the display and the time indication changes to the daylight saving time (summer time).

To deactivate the daylight saving time (summer time) adjustment, press DST again.

then the ALARM indicator lights up in the

display. (It does not appear when the switch is set

to OFF.)

2 Slide ALARM TIME SET + or – to set

the desired time.

Each slide of ALARM TIME SET + or – changes

the indication by 1 minute. If you keep sliding

ALARM TIME SET + or –, the alarm time goes

forward (or backward) by 1 minute up to 10 minutes,

and then by 10 minutes increments. While setting the

alarm time, the ALARM indicator flashes in the

display.

ALARM

When the alarm time setting operation is complete, the display returns to the clock after a few seconds and the ALARM indicator changes from flashing to fully lit.

•While ALARM MODE is set to RADIO or BUZZER, the alarm time setting can be changed by

ALARM TIME SET.

One slide of ALARM TIME SET displays the alarm time for about 4 seconds. By adjusting ALARM TIME SET while the alarm time appears in the display, the alarm time will be changed.

•The ALARM indicator flashes in the display while:

–The alarm time appears in the display.

–The alarm sounds.

–Snooze function is turned on.

•The alarm time setting cannot be changed if

ALARM MODE is set to OFF. If ALARM TIME SET is adjusted, “OFF” appears in the display for about 0.5 seconds.

•CLOCK, DST, and TIME ZONE are unavailable while the alarm sounds or snooze function is turned on.

•The alarm function works as usual at the beginning and end day of the daylight saving time (summer time). While the Automatic DST/Summer Time adjustment is set, as a result, if the alarm is set at a time skipped when the daylight saving time (summer time) begins, the alarm is skipped, or if the alarm is set at a time overlapped when the daylight saving time (summer time) ends, the alarm sounds twice.

Two short beeps sound when the display returns to “90”.

The radio will play for the duration you set, then shut off.

To turn off the radio before the preset time

Press RADIO OFF/ALARM RESET or

SNOOZE/DATE/SLEEP OFF.

To use both sleep timer and alarm

You can fall asleep to the radio and also be awakened by the radio or buzzer alarm at the preset time.

1Set the alarm. (See “Setting the alarm”.)2Set the sleep timer. (See “Setting the sleep timer”.)