Sony LBT-GTZ4I - page 42

42GB

Transferring to an USB device results

in an error.

• You are using an unsupported USB

device. See “Compatible USB devices

with this system” (page52) for the

supported device types.

• The USB device was disconnected or

the power was turned off during

transferring. Delete the partially-

transferred file, and transfer again. If

this does not fix the problem, the USB

device may be broken. Refer to the USB

device operating instruction on how to

deal with this problem.

• Turn off the system and remove the

USB device. If the USB device has a

power switch, turn the USB device off

and then on again after removing it from

the system. Then perform transferring

again.

Audio files or folders on the USB

device cannot be erased.

• Check if the USB device is write-

protected.

• The USB device was disconnected or

the power was turned off during the

erase operation. Delete the partially-

erased file. If this does not fix the

problem, the USB device may be

broken. Refer to the USB device

operating instruction on how to deal

with this problem.

Are you using a supported USB

device?

• If you connect an unsupported USB

device, the following problems may

occur. See “Compatible USB devices

with this system” (page52) for the

supported device types.

–The USB device is not recognized.

–File or folder names are not displayed

on this system.

–Playback is not possible.

–The sound skips.

–There is noise.

–A distorted sound is output.

–Transferring stops before it is finished.

“OVER CURRENT” appears.

• A problem has been detected with the

level of electrical current from the

A port or B port. Turn off the

system and remove the USB device

from the A port or B port. Make

sure there is no problem with the USB

device. If this display pattern persists,

contact your nearest Sony dealer.

There is no sound.

• The USB device is not connected

correctly. Turn off the system and

reconnect the USB device, then turn on

the system and check if “USB A” or

“USB B” lights up in the display.

There is noise, skipping, or distorted

sound.

• Turn off the system and reconnect the

USB device, then turn on the system.

• The music data itself contains noise, or

the sound is distorted. Noise may have

entered during the transferring process.

Delete the file, and try transferring

again.

The USB device cannot be

connected into the A port or

B port.

• The USB device is being connected

backwards. Connect the USB device in

the correct orientation.

Contents

Main Except for the customers in the United States Notice for the customers in the United States Owners Record WARNING WARNING CAUTION Important Safety Instructions For customers in Europe For customers in Australia Note on DualDiscs Music discs encoded with copyright protection technologies About this manual Table of Contents Getting Started Basic Operations Additional Information Other Operations Guide to parts and controls Page Page Remote RM-AMU054 (MHC-GTZ4i / GTZ3i / GTZ2i and LBT-GTZ4i only) V / v/ b / B Remote RM-AMU053 (Other models) Page Hooking up the system securely Getting Started F E A B C D Attaching the speaker pads Setting the clock 1 2 6 3 V/v (RM-AMU054) repeatedly to Playing an AUDIO CD/ MP3 disc 1 2 3 4 press VOLUME +/ on the remote) to adjust the volume. Basic Operations To change the play mode 1 2 Listening to the radio 1 2 3 4 Transferring onto an USB device 1 CD-USB Synchronized Transfer 2 3 4 1 2 3 4 1 2 3 Transferring a single track or MP3 file during playback (REC1 Transferring) Transferring from a sound source other than disc and USB device (Analog Transferring) 4 5 To stop transferring To create a new MP3 file To transfer sound from a microphone 4 1 2 3 4 1 2 3 4 You can select a Memory Stick when the selected memory number is as follows: 5 REC1 Transferring the memory you want. 6 7 in the selected memory of the mobile phone or start transferring. Listening to music of an USB device 1 2 3 4 1 2 3 4 5 To change the play mode Playing the iPod (MHC-GTZ4i/GTZ3i/GTZ2i and LBT-GTZ4i only) You can listen to audio contents stored in the iPod on this system. 1 B port. B To use the system as a battery charger To stop charging the iPod Remove the iPod. When the system is turned off, the charging is stopped. Using optional audio components 1 2 3 4 5 Changing the display 1 2 3 4 5 To exit the OPTIONS menu To return to the previous display Using the Meter Display Creating your own program Program Play 1 2 3 Presetting radio stations 1 2 3 4 Using the Radio Data System (RDS) (European model only) What is the Radio Data System? Receiving RDS broadcasts To check the RDS information Creating your own sound effect Singing along 1 2 3 4 Using the Timers 1 2 7 3 4 1 2 3 4 5 Troubleshooting 1 2 General Additional Information Disc player USB device Page iPod Tuner Meter Optional components To change the AM tuning interval (except for European models) 1 Messages Disc/Timer USB device Precautions Discs that this system CAN play Discs that this system CANNOT play Notes on discs On safety Specifications AUDIO POWER SPECIFICATION Amplifier section USB section Disc player section Tuner section iPod section Speakers Front speaker (SS-GTZ5M) Subwoofer (SS-WGZ5M) General Compatible USB devices with this system You can use the following Sony USB devices and Sony Ericsson mobile phone on this system. Verified Sony USB device Verified Sony Ericsson mobile phone Notes on using the Sony Ericsson mobile phone Notes on Walkman Walkman phone Compatible iPod models with this system