Wireless Stereo Headphone System
Operating Instructions
NGetting started
Unpacking
Check that you have the following items:
• The headphones (1)
• The transmitter (1)
5 Rest the headphones on the transmitter so that the transmitter’s POWER/CHG indicator lights in red.
Please place the headphones on the transmitter so that the triangle arrow would be matched. If the headphones are not properly placed, it will not be charged.
Charging will take about 16 hours, after which the POWER/CHG indicator will go off.
Headphones
LR
POWER/CHG
(Using Sony alkaline batteries
Model | Approx. hours*1 |
28 hours*2 | |
22 hours*2 |
*1 at 1 kHz, 1 mW+1 mW output
*2 Time stated above may vary, depending on the temperature or conditions of use.
Notes on Batteries•Do not charge a dry battery.
•Do not carry a dry battery together with coins or other metallic objects. It can generate heat if the positive and negative terminals of the battery accidentally come into contact with metallic objects.
•If you are not going to use the unit for a long time, remove the batteries to avoid damage from battery leakage or corrosion.
Checking the remaining battery powerPull up the
1 2 3 | R | A | L INPUT B |
CHANNEL | DC IN 12V |
|
|
To DC IN | Transmitter |
| |
12V jack | To an AC |
| outlet |
| AC power adaptor |
| (supplied) |
•Use only the supplied AC power adaptor. Do not use any other AC power adaptor.
Polarity of the plug
B
Press the TUNING button briefly for automatic tuning of the headphones. If you do not receive a clear audio signal, press it again.
When tuning has completed, turn up the volume to a moderate level with the VOLUME control on the right housing.
| R |
VOLUME control | TUNING |
| button |
VOLUME | TUNING |
The transmitter starts sending RF signals automatically when it detects an audio signal from the connected equipment.
If it does not detect an audio signal for more than about 4 minutes, the transmitter will stop sending RF signals, and the POWER/CHG indicator will turn off. When the transmitter receives an audio signal again, it starts sending the RF signals, and the POWER/CHG
Replacing the ear pads
The ear pads are replaceable. If the ear pads become dirty or worn out, replace them as illustrated below. The ear pad is not commercially available. You can order replacements from the store where you purchased this system, or at your nearest Sony dealer.
1 Remove the old ear pad by pulling it out of the groove on the housing.2 Place the new ear pad on the driver unit.Troubleshooting
No sound/Muffled sound, Check the connection of the audio/video |
equipment or the AC power adaptor. |
, Check that the audio/video equipment is |
turned on. |
, Turn up the volume on the connected audio/ |
video equipment, if the transmitter is |
connected to the headphones jack. |
, Change the radio frequency with the |
CHANNEL selector switch on the transmitter, |
then set to the same radio frequency with the |
TUNING selector (or TUNING button) on the |
right housing of the headphones. |
, The mute function is activated. |
• Use the headphones near the transmitter. |
, The headphones’ POWER indicator light turns |
off, dims, flashes, or sound becomes distorted |
or noisy. |
• Charge the rechargeable battery if it is weak, |
or replace alkaline batteries with new ones. If |
the POWER indicator is still off after charging |
the battery, take the headphones to a Sony |
Härmed intygar Sony Corp. att denna utrustning står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. För ytterligare information gå in på följande hemsida: http://www.compliance.sony.de/
DanskUndertegnede, Sony Corp. erklærer herved, at følgende udstyr overholder de væsentlige krav og øvrige relevante krav i Direktiv 1999/5/EF. For yderligere information gå ind på følgende hjemmeside: http://www.compliance.sony.de/
SuomiSony Corp. vakuuttaa täten että tämä laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Halutessasi lisätietoja käy osoitteessa: http://www.compliance.sony.de/
• AC power adaptor (1) |
indicator
Transmitter
batteries if the POWER indicator light dims, flashes, or the sound becomes distorted or noisy.
Note• When the transmitter is placed on or near a TV, it |
may pick up a noise. In such a case, place the |
transmitter away from the TV. |
• If the connected equipment has the AVLS |
indicator will light up green again.
If the audio signal is very weak, the transmitter does not send RF signals. If the transmitter is connected to a headphone jack, make sure the volume of the
Hang the edge of the ear pad on one side of the driver unit’s groove edge, then turn the edge of ear pad around the driver unit as illustrated below.
dealer. |
, If the transmitter is connected to the |
Sony Corp. erklærer herved at utstyret er i samsvar
• Connecting cord (1) (phono plugs y stereo |
miniplug), 1 m |
• Unimatch plug adaptor (1) (stereo mini jack y |
stereo phone plug) |
• Rechargeable |
This system employs a contactless charge method that requires no terminals by the electromagnetic induction.
Notes
•Do not leave any metallic objects (coin, clip, etc.) near the transmitter’s charging point. The transmitter and the metal might become hot and it is
dangerous.
Charging point
•Do not leave any objects susceptible to magnetism (cash cards, floppy disks with magnetic coding, etc.) near the system. Exposure to the transmitter’s electromagnetic field may render them unusable.
LR
Headphones
The rechargeable
Setting up the transmitter
1 Connect the transmitter to audio/video equipment.Select one of the hookups below depending on the jack type:
A To connect to a headphones jack
Transmitter
To INPUT A jacks
(Automatic Volume Limiter System) function, be |
sure to turn the function off when using the |
transmitter. Otherwise, you will have to turn up the |
volume of the headphones, and that may cause |
noise. |
NOperating the system
Listening to a programme
Before listeningTo reduce the risk of hearing damage, first lower the volume.
1 Turn on the audio/video equipment connected to the transmitter.If the transmitter is connected to the headphone jack, set the volume control of the audio source equipment as high as possible but not so high that the audio signal becomes distorted.
2 Remove the headphones from the transmitter.equipment connected is set to 5 - 6 or higher.
You may not hear the beginning of the sound from the headphones until the transmitter starts sending the RF signals after detecting an audio signal.
The headphones automatically turn off when they are taken off– Auto power on/off functionDo not pull up the
Self- adjusting band
Notes
• If hiss is heard, move closer to the transmitter. |
When the ear pad is securely inserted into the groove, adjust the ear pad to the vertical position.
NAdditional information
Precautions
•If the transmitter is not to be used for a long period of time, disconnect the AC power adaptor from the AC outlet by holding the plug. Do not pull on the cord.
•Do not leave the wireless stereo headphone system in a location subject to direct sunlight, heat or moisture.
headphones jack, turn down the volume on the |
connected audio/video equipment. |
, Change the radio frequency with the |
CHANNEL selector switch on the transmitter, |
then set to the same radio frequency with the |
TUNING selector (or TUNING button) on the |
right housing of the headphones. |
, The headphones’ POWER indicator light turns |
off, dims, flashes, or sound becomes distorted |
or noisy. |
• Charge the rechargeable battery if it is weak, |
or replace alkaline batteries with new ones. If |
the POWER indicator is still off after charging |
the battery, take the headphones to a Sony |
dealer. |
, Move closer to the transmitter. As you move |
away from the transmitter, more noise is likely |
to be heard. |
, If the transmitter is connected to the |
headphones jack, turn up the volume of the |
connected audio/video equipment. |
, Change the radio frequency with the |
CHANNEL selector switch on the transmitter, |
med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF. Gå til denne
Με την παρ ύσα η Sony Corp. ∆ηλώνει τι αυτς ε πλισµς συµµ ρώνεται πρ ς της υσιώδεις
απαιτήσεις και της λ ιπές σετικές διατάεις της δηγίας 1999/5/EK. Για λεπτ µέρειες
παρακαλ ύµε πως ελέγετε την ακλ υθη σελίδα τ υ διαδικτύ υ: http://www.compliance.sony.de/
FrançaisPar la présente, Sony Corp. déclare que ce type d’appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Pour toute information complémentaire, veuillez consultez l’URL suivante : http://www.compliance.sony.de/
DeutschHiermit erklärt Sony Corp., dass sich dieses Gerät in
MDR-RF840RK
MDR-RF860RK
© 2007 Sony Corporation Printed in ChinaCharging the supplied rechargeable battery
The supplied rechargeable
To charge the headphones, place them on the transmitter.
1 Press the PUSH button of the left housing to open the battery compartment lid.
Rechargeable battery
Lines of magnetic force
Transmitter
• Do not place a radio near the system. A noise may be |
heard from the radio. In such a case, change the |
1 2 3 | R | A | L INPUT B |
CHANNEL | DC IN 12V |
|
|
Right | Left channel |
channel (red) | (white) |
The transmitter’s POWER/CHG indicator lights up green.
Headphones
• You may hear some noise when you disconnect the |
AC power adaptor from the transmitter before turn |
off the headphones. |
The transmitter unit compresses the audio signal and converts it to RF signal. The headphones unit converts the received RF signal to an audio signal and decompresses it.
This process reduces noise picked up during
Avoid using headphones at high volume. Hearing experts advise against continuous, loud and extended play. If you experience a ringing in your ears, reduce the volume or discontinue use.
Caring for othersKeep the volume at a moderate level. This will allow you to hear outside sounds and to be considerate to the people around you.
then set to the same radio frequency with the |
TUNING selector (or TUNING button) on the |
right housing of the headphones. |
, The headphones’ POWER indicator light turns |
off, dims, flashes, or sound becomes distorted |
or noisy. |
• Charge the rechargeable battery if it is weak, |
or replace alkaline batteries with new ones. If |
the POWER indicator is still off after charging |
the battery, take the headphones to a Sony |
dealer. |
Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. Weitere Informationen erhältlich unter: http://www.compliance.sony.de/
EspañolPor medio de la presente, Sony Corp. declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Para mayor información,
WARNING
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
To reduce the risk of fire or electric shock, do not place objects filled with liquids, such as vases, on the apparatus.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Connect AC power adaptor to an easily accessible AC outlet. Should you notice an abnormality in AC power adaptor, disconnect it from the AC outlet immediately.
Do not install the appliance in a confined space, such as a bookcase or
Do not expose the battery to excessive heat such as direct sunlight, fire or the like.
Hereby, Sony Corp., declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
For details, please access the following URL : http://www.compliance.sony.de/
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.
Welcome!
Thank you for purchasing the Sony
Some features are:
•A compact transmitter enables simple charging by a contactless charge method that requires no terminals by the electromagnetic induction.
Just by placing the headphones on the transmitter, the headphone battery can be charged.
•Automatic ON/OFF function on headphones to preserve battery power.
•Noise reduction system to reproduce a clear sound with minimum transmission noise.
•Wireless system that allows you to listen to a program free from the restriction of a cord
•High fidelity sound reproduction
•Easy connection with TV and HiFi Audio system equipment
•Up to 100 meters reception range
•Volume control function on the headphones.
•Comfortable
Notes on receiving performance
This system utilizes very high frequency signals in the 800 MHz band so the receiving performance may deteriorate due to the surroundings. The following examples illustrate conditions that may reduce the reception range or cause interference.
•Inside a building with walls containing steel beams.
•An area with many steel file cabinets, etc.
•An area with many electrical appliances capable of generating electromagnetic fields.
•The transmitter is placed on a metal instrument.
•An area facing a roadway.
•Noise or interfering signals exist in the surroundings due to radio transceivers in trucks, etc.
•Noise or interfering signals exist in the surroundings owing to wireless communication systems installed along roadways.
The battery compartment lid comes off.
L
PUSH button
2 Insert the supplied rechargeable nickel- metal hydride battery into the battery compartment matching the 3 terminal on the battery to the 3 mark in the compartment.
Do not use rechargeable battery other than the supplied one.
3 Close the battery compartment lid.1Insert the tab into the hole at the upper left. 2Close the lid until it clicks.
1 L
2
4 Connect the supplied AC power adaptor to the transmitter.1 2 3 | R | A | L INPUT B |
CHANNEL | DC IN 12V |
|
|
To DC IN | Transmitter |
| |
12V jack | To an AC |
| outlet |
| AC power adaptor |
| (supplied) |
angle of the radio or move away from the system so |
that a noise is not heard. |
Check if the right and left headphones are rested on the transmitter correctly. Remove the headphones and replace them on the transmitter again so that the POWER/CHG indicator lights in red.
To recharge the headphone battery after usePlace the headphones on the transmitter after use. Since the
Notes
•The transmitter automatically stops sending RF signals while charging the battery.
•This system is designed to charge only the supplied rechargeable battery type
•If dry batteries are installed, they cannot be charged.
•Do not attempt to use the supplied
•Charge in an environmental temperature of between 0 °C and 40 °C (between 32 °F and 104 °F).
Charging and usage hoursApprox. charging | Approx. usage time*1 | ||
hours*1 |
|
| |
| |||
1 hour | 60 minutes*3 | 40 minutes*3 | |
16 hours*2 | 18 hours*3 | 14 hours*3 |
*1 at 1 kHz, 1 mW+1 mW output
*2 hours required to fully charge an empty battery *3 Time stated above may vary, depending on the
temperature or conditions of use.
Using the headphones with dry batteries (sold separately)Commercially available (size AAA) dry batteries can also be used to power the headphones. Install the batteries in the same manner as described in steps 1 through 3 of “Charging the supplied rechargeable battery.”
When dry batteries are installed, the battery charge function will not be activated.
Connecting cord |
(supplied) |
To headphones
Unimatch plug | jack (Stereo | |
adaptor | ||
mini jack) | ||
(supplied) | ||
|
To headphones | WALKMAN*, |
jack (Stereo | TV, etc. |
phone jack) |
|
B To connect to LINE OUT or REC OUT
Transmitter
To INPUT B jack
1 2 3 | R | A | L INPUT B |
CHANNEL | DC IN 12V |
|
|
Connecting cord (supplied)
Right | Left channel |
channel (red) | (white) |
To LINE OUT or
REC OUT jacks
Stereo system,
VCR, etc.
*“WALKMAN” and “WALKMAN” logo are registered trademarks of Sony Corporation.
Transmitter
3 Select the radio frequency with the CHANNEL selector switch.1 2 3
CHANNEL
4 Put on the headphones.When you put on the headphones, the headphone’s power turns on automatically.
The POWER indicator on the right housing glows red.
Be sure to put the right housing R on your right ear and the left housing L on your left ear. Wear the headphones vertically on your head so that auto power on function is properly activated.
5 Set the channel to that of the transmitter with the selector (or button) on the right housing of the headphones.
A
Select the channel to that of the transmitter with the TUNING selector on the right housing of the headphones.
When tuning has completed, turn up the volume to a moderate level with the VOLUME control on the right housing.
| R |
|
|
VOLUME control | TUNING | ||
| selector | ||
| 1 | 2 | 3 |
VOLUME |
|
|
|
transmission.
Transmitter unit |
|
| Headphones unit | |
rangedynamic | input signal | RF transmission | output signal | |
|
|
| 2 34 | noise level (low) |
| 1 compression | decompression | 5 |
1The transmitter unit compresses the audio signals dynamic range, then converts it to RF signal.
2Noise may occur due to long distance transmission, etc.
3The headphones unit converts the RF signal to an audio signal.
4Noise may occur during conversion.
5Decompression of the audio signals dynamic range reduces the noise level and improves the
S/N
The effective areas of the transmitter
The optimum distance is up to approximately 100 m without the system picking up some interference. However, the distance may vary depending on the surroundings and environment. If the system picks up some noise within the above mentioned distance, reduce the distance between the transmitter unit and the headphones, or select another channel.
Notes
•When you use the headphones inside the effective areas of the transmitter, the transmitter can be placed in any direction from the listener.
•Even within the signal reception area, there are some spots (dead spots) where the RF signal cannot be received. This characteristics is inherent to RF signals, and does not indicate malfunction. By slightly moving the transmitter, location of the dead spot can be changed.
If you have any questions or problems concerning the system that are not covered in this manual, please consult your nearest Sony dealer.
Be sure to bring the headphones and the transmitter to the Sony dealer when requiring repair work.
Specifications
GeneralCarrier frequency
863.52 MHz, 864.02 MHz, 864.52 MHz
Channel | Ch1, Ch2, Ch3 |
Modulation | FM stereo |
Frequency response
Power source | DC 12 V: supplied AC power adaptor |
Audio input | Phono jacks, stereo mini jack |
Dimensions | Approx. 216 ⋅ 105 ⋅ 96 mm |
| (8 5/8 ⋅ 4 1/4 ⋅ 3 7/8 in) (w/h/d) |
Mass | Approx. 220 g (7.77 oz) |
Rated power consumption 3 W
HeadphonesPower source | Supplied rechargeable |
| hydride battery |
| commercially available (size AAA) dry |
| batteries |
Mass | Approx. 300 g (10.59 oz) incl. Battery |
Design and specifications are subject to change without notice.
por favor consulte el siguiente URL: http://www.compliance.sony.de/
NederlandsHierbij verklaart Sony Corp. dat dit apparaat in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Nadere informatie kunt u vinden op: http://www.compliance.sony.de/
ItalianoCon la presente Sony Corp. dichiara che questo apparecchio è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Per ulteriori dettagli, si prega di consultare il seguente URL: http://www.compliance.sony.de/
PortuguêsA Sony Corp. declara que este equipamento está conforme com os requisitos essenciais e outras provisões da Directiva 1999/5/CE. Para mais informações, por favor consulte a seguinte URL: http://www.compliance.sony.de/