Sony SA-VE325 Positioning the speakers, Specifications, Listening to the sound (I), Adjusting the sound, Troubleshooting, 扬声器的定位, 听声音（I）, 调整声音, 故障检修, Setting the speakers

Micro Satellite System

SA-VE325

	Center
	中央
	Subwoofer
	超低音扬声器
Front (Left)	Front (Right)
前（左）	前（右）

Rear (Left)	Rear (Right)
后（左） B	B 后（右）

Foot pads

脚垫

Foot pads

脚垫

WS-WV10A(for rear speakers)（用于后置扬声器）WS-FV10A WS-TV10A

		AUTO
ON / STANDBY	MOVIE
		MUSIC
		OFF
LEVEL	MODE	POWER SAVE
MINMAX

POWER LEVEL ON/STANDBY indicator MODEON/STANDBY 指示灯

English

Positioning the speakers

Location of each speaker (D)

Each speaker should face the listening position. Better surround effect will result if all speakers are set at the same distance from the listening position.

Place the front speakers at a suitable distance to the left and right of the television.

Place the subwoofer on either side of the television. Place the center speaker on the top-center of the TV set. The placement of rear speakers greatly depends on the configuration of the room. The rear speakers may be placed on both sides of the listening position Aor behind the listening position B.

Tips

•Movies are best enjoyed in a room that produces no echoes (as in one with surrounding curtains).

•Music (especially classical music) is best enjoyed in a room that produces some echo.

Setting the speakers

To prevent speaker vibration or movement while listening, attach the supplied foot pads to the bottom four corners of the center speaker, front speakers, and rear speakers (E).

Setting the center speaker (F)

Set the center speaker firmly on top of the TV set, making sure it is completely level.

Notes

•Some amplifier functions for enhancing the sound may cause distortion in the subwoofer. If such distortion occurs, turn off those functions.

•To enjoy high-quality sound, do not turn the subwoofer volume too high.

•To increase the bass sound from the subwoofer, connect the system using “Hookup B”.

•The bass sound is enhanced in MOVIE mode rather than in MUSIC mode. Therefore, if you change the mode to MOVIE while listening to some sources that do not include the bass sound, you may not be able to get the effect.

Setting amplifier to enjoy movies

For the Dolby Digital (AC-3)

If your amplifier is connected internally or externally with a Dolby Digital (AC-3) processor, you should use the setup menus for the amplifier to specify the parameters of your speaker system.

See the table below for the proper settings. For details on the setting procedure, refer to the manual that was provided with your amplifier.

Select Micro Satellite Position if a Sony amplifier provides it.When “Hookup A” is used (Speaker setup)

For

Set to

Specifications

SS-V325 (front and rear speakers)

Speaker system	Full range,
	magnetically shielded
Speaker units	5.5 ⋅ 11 cm, cone type
Enclosure type	Bass reflex
Rated impedance	8 ohms
Power handling capacity
Maximum input power:	100 watts
Sensitivity level	87 dB (1 W, 1 m)
Frequency range	90 Hz - 20,000 Hz
Dimensions (w/h/d)	Approx. 70 ⋅ 152 ⋅ 126
	mm, including front
	grille
Mass	Approx. 830 g each
SS-CN325 (center speaker)
Speaker system	Full range ⋅ 2,
	magnetically shielded
Speaker units	5.5 ⋅ 11 cm, cone type
Enclosure type	Bass reflex
Rated impedance	8 ohms
Power handling capacity
Maximum input power:	120 watts
Sensitivity level	89 dB (1 W, 1 m)
Frequency range	90 Hz - 20,000 Hz
Dimensions (w/h/d)	Approx. 300 ⋅ 78 ⋅
	126 mm, including front
	grille

中文

扬声器的定位

各扬声器的配置（D）

每一个扬声都须向着听者位置。如能把所有扬声器都设定与听者呈相等距离时，便可获得较佳的环绕声效果。把前扬声器配置在电视机左右适当距离处。把超低音扬声器放在电视机的任何一边。把中央扬声器放在电视机顶上中央。后扬声器的安放位置受房间配置的影响很大。后扬声器可安放在听者位置的两旁位置 A或听者位置后面的 B位。

要领

•能在不产生回音的房间里欣赏电影是一大享受（室内周围屏障所发生的回音）。•音乐（特别是古典乐）则最好能在可产生回音的室内欣赏，其音响效果最佳。

设定扬声器

为防止在收听时扬声器振动或移动，将附带的脚垫附装在中央扬声器、前置扬声器和后置扬声器（E ）的四个底脚上。设定中央扬声器（F）将中央扬声器稳固地放在电视机顶部，务必使其完全水平放置。设定其它扬声器（G）为了在扬声器定位中获得更大的适应性，请采用选购件WS-FV10A，WS-TV10A或 WS-WV10A扬声器座架（仅在某些国家有售）。

注

•一部分放大器起强化音响作用时，可能使副低音扬声器发生声音失真现象。如果发生这样的失真现象时，即请关掉其功能。•要获得高音质音响时，不要把副低音扬声器的音量转得太大。•要加强副低音扬声器的低音时，请用“B式联结”连接系统。

•低音在 MOVIE 模式而并非在 MUSIC 模式被强化。因此，如果您在收听某些不包括低音的声源时将模式变为 MOVIE 模式，可能收不到低音效果。

设定放大器用于欣赏电影

杜比数码（AC-3）时如果放大器内装或外连有杜比数码（AC-3）处理器时，您应使用设定选单为放大器指定扬声器系统的参数。请按照下表进行适当的设定。有关设定方法的详细内容，请参照您的放大器附带的说明书。如果 Sony 放大器提供此功能请选择 Micro Satellite Position。使用“A 式联结”时（扬声器调定）

对	请设定为
前扬声器	SMALL
中央扬声器	SMALL
后扬声器	SMALL
副低音扬声器	ON（或 YES）

规格

SS-V325（前、后扬声器）

扬声器系统	全音频范围，磁屏蔽型
扬声器单元	5.5×11 cm，锥型
盒型	低音反射
额定阻抗	8 Ω
功率使用容量
最大输入功率	100 W
灵敏度水平	87	dB（1 W，1 m）
频率范围	90	Hz～20,000 Hz

尺寸（宽／高／纵深）大约 70×152×126 mm，含

	前格栅
质量	大约 830 g／每个
SS-CN325（中央扬声器）
扬声器系统	全音频范围 ×2，磁屏蔽型
扬声器单元	5.5×11 cm，锥型
盒型	低音反射
额定阻抗	8 Ω
功率使用容量
最大输入功率	120 W
灵敏度水平	89 dB（1 W，1 m）
频率范围	90 Hz～20,000 Hz

尺寸（宽／高／纵深）大约 300×78×126 mm，含

	前格栅
质量	大约 1600 g／每个
SA-WMS325（副低音扬声器）
扬声器系统	有源副低音扬声器，磁屏蔽型

Setting other speakers (G)

For greater flexibility in the positioning of the speakers, use the optional WS-FV10A, WS-TV10A, or WS-WV10A speaker stand (available only in certain countries).

Tip

The height of the front speakers should be adjusted to about the center of the TV screen (H).

Listening to the sound (I)

First, turn down the volume on the amplifier. The volume should be set to minimum before you begin playing the program source.

1 Turn on the amplifier and select the program source.

2 Press POWER on the subwoofer.

The ON/STANDBY indicator on the subwoofer lights up green.

3 Play the program source.

Power turns on and off automatically — Autopower on/off function (J)

When the subwoofer is on (i.e, the ON/STANDBY indicator lights up green) and there is no signal input for a few minutes, the ON/STANDBY indicator changes to red and the subwoofer enters power saving mode. While in this mode a signal is input to the subwoofer, the subwoofer automatically turns on (auto power on/off function).

To turn this feature off, slide the POWER SAVE switch on the rear panel to OFF.Note

If you turn down the volume level of the amplifier too low, the auto power on/off function may activate, causing the subwoofer to enter power saving mode.

Adjusting the sound

Slight adjustments to the system can enhance your sound enjoyment.

Adjusting the subwoofer (I)

1 Set MODE according to the program source as follows:

	Source	MODE
	DVD, LD, video cassette	MOVIE
	or other video source

	MD, CD, cassette tape	MUSIC
	or other audio source

Front speakers	SMALL
Center speaker	SMALL
Rear speakers	SMALL
Subwoofer	ON (or YES)

When “Hookup B” is used (Speaker setup)

For	Set to
Front speakers	LARGE
Center speaker	SMALL
Rear speakers	SMALL
Subwoofer	OFF (or NO)

For the Dolby Pro Logic

If your amplifier is connected internally or externally with a Dolby Pro Logic processor, you should set the surround effect mode to “NORMAL” on the amplifier for your particular speaker system.

For details on the setting procedure, refer to the manual that was provided with your amplifier.

Troubleshooting

Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer.

There is no sound from the speaker system.•Make sure all the connections have been correctly made.•Make sure the volume on the amplifier has been turned up properly.

•Make sure the program source selector on the amplifier is set to the proper source.

•Check if headphones are connected. If they are, disconnect them.There is distortion in the subwoofer sound output.

•Check if any sound-enhancing functions have been activated on the amplifier. If they have, turn them off.

There is hum or noise in the speaker output.

•Make sure all the connections have been correctly made.

•Make sure none of the audio components are positioned too close to the TV set.The sound has suddenly stopped.

•Make sure all the connections have been correctly made. Contact between bare speaker wires at the speaker terminals may cause a short-circuit.

Mass	Approx. 1600 g
SA-WMS325 (subwoofer)
Speaker system	Active subwoofer,
	magnetically shielded
Speaker unit	Woofer: 16 cm, cone type
Enclosure type	Advanced SAW type

Reproduction frequency range28 Hz - 200 HzAmplifier sectionContinuous RMS power output75 W (8 ohms, 20 Hz -20 kHz, 0.8% THD)InputsLINE IN (input pin jack)SPEAKER IN (input terminals)OutputsLINE OUT (output pin jack)SPEAKER OUT (output terminals)

General
Power requirements	110 - 120 V/220-240 V
	AC, 50/60 Hz
Power consumptions	70 W
	1 W (standby mode)
Dimensions (w/h/d)	Approx. 205 ⋅ 385 ⋅ 389
	mm, including front grille
Mass	Approx. 10.3 kg

Supplied accessoriesFoot pads (20)Audio connecting cord (1)Speaker connecting cords, 10 m (2)Speaker connecting cords, 3.5 m (3)Speaker connecting cords, 2.5 m (2)Design and specifications are subject to change without notice.

要领

前置扬声器的高度应调整到电视机荧幕（H）中心左

右。

听声音（I）

首先，请转小放大器上的音量控制。在开始播放节目信号源之前，必须把音量设定到最小。1 打开放大器电源，选择节目信号源。2 按副低音扬声器上的 POWER 。超低音扬声器上的 ON/STANDBY 指示灯即点亮绿色。3 播放节目信号源。自动地打开和关掉电源－自动电源开／关功能（J）

当副低音扬声器打开着电源（亦即 ON/STANDBY 指示灯点亮着绿色）而在几分钟里没输入信号时，ON/STANDBY 指示灯将变亮红色而副低音扬声器即将进入节电模式。在此模式时，如果有信号输入到副低音扬声器，副低音扬声器便可自动地打开电源（自动电源开／关功能）。

要关掉此功能时，可把后面板上的 POWER SAVE 开关推到 OFF（关掉）位置。

注

您如果把放大器的音量电平调得太低，自动电源开／关功能即可能会被激活（打开），而使副低音扬声器进入节电模式。

调整声音

轻调一下系统便可提高音响享受。

调整副低音扬声器(I)

1 根据如下节目信号源设定 MODE（模式）：

信号源	MODE
DVD、LD、录音带或	MOVIE
其它视频信号源
MD、CD、录音带或	MUSIC
其它声频信号源

2 旋转 LEVEL 以调整音量。根据节目信号源将音量调整到最适合您喜好的水平。

使用“B 式联结”时（扬声器调定）

对	请设定为
前扬声器	LARGE
中央扬声器	SMALL
后扬声器	SMALL
副低音扬声器	OFF（或 NO）

杜比专业逻辑时如果放大器内装或外连接有杜比专业逻辑信息处理机时，您便须为您的特殊的扬声器系统在放大器中把环绕声效果模式设定于“NORMAL”（正常）。有关设定方法的详细内容，请参照放大器附带的说明

书。

故障检修

使用扬声器系统如果遭遇问题，即请按照下列各项进行检查和测定。仍不能解决问题时，请洽询附近 Sony 销售店。扬声器系统没声音。•确认所有的接线是否都连接正确。•确认放大器的音量控制是否旋调适当。•确认放大器的节目信号源选择器是否已设定于适当的信号源。•检查是否接插着耳机。如果是，即将其拆卸下来。副低音扬声器输出声发生失真。•检查放大器上的任何声音加强功能是否被打开了。如果是，即将其关掉。扬声器输出声带交流哼声或杂音。

•确认所有的接线是否都连接正确。

•确认各声频组成机是否没太靠近电视机配置。声音突然停止。•确认所有接线是否都连接正确。扬声器各端子间的扬声器裸线部分相接触时，可能引起短路。

扬声器单元	低音扬声器：16 cm，锥型
盒型	先进的 SAW 型
再现频率范围	28	Hz～200 Hz
放大器部分
连续 RMS 功率输出	75	W（在 20 Hz～20 kHz 时
	为 8 Ω，0.8 ％ THD）

输入端子LINE IN（输入管脚插孔）SPEAKER IN（输入端子）输出端子LINE OUT（输出管脚插孔）SPEAKER OUT（输出端子）

一般规格
电源	110～120/220～240 V AC，
	50/60 Hz
电力消耗	70 W

尺寸（宽／高／纵深）大约 205×385×385 mm，含

	前格栅
质量	大约 10.3 kg

附件

脚垫（20）声频连接导线（1）扬声器连接导线，10 m（2）扬声器连接导线，3.5 m（3）扬声器连接导线，2.5 m（2）设计和规格有所变更时，恕不另行奉告。

2 Rotate LEVEL to adjust the volume.

Set the volume level to best suit your preference according to the program source.

Sony SA-VE325 Positioning the speakers, Specifications, Listening to the sound (I), Adjusting the sound, Troubleshooting, 扬声器的定位, 听声音（I）, 调整声音, 故障检修, Setting the speakers

Positioning the speakers

Location of each speaker (D)

Setting the speakers

Setting amplifier to enjoy movies

Specifications

扬声器的定位

各扬声器的配置（D）

设定扬声器

设定放大器用于欣赏电影

Listening to the sound (I)

1 Turn on the amplifier and select the program source.

2 Press POWER on the subwoofer.

3 Play the program source.

Adjusting the sound

Adjusting the subwoofer (I)

1 Set MODE according to the program source as follows:

Troubleshooting

听声音（I）

调整声音

调整副低音扬声器(I)

故障检修

2 Rotate LEVEL to adjust the volume.

上海索广电子有限公司

上海市闵行区剑川路930号

Positioning the speakers

Location of each speaker (D)

Setting the speakers

Setting amplifier to enjoy movies

Specifications

扬声器的定位

各扬声器的配置（D）

设定扬声器

设定放大器用于欣赏电影

Listening to the sound (I)

1 Turn on the amplifier and select the program source.

2 Press POWER on the subwoofer.

3 Play the program source.

Adjusting the sound

Adjusting the subwoofer (I)

1 Set MODE according to the program source as follows:

Troubleshooting

听声音（I）

调整声音

调整副低音扬声器(I)

故障检修

2 Rotate LEVEL to adjust the volume.

上海索广电子有限公司

上海市 闵行区 剑川路930号

上海市闵行区剑川路930号