Operations
Playing/searching at various speeds
H PLAY A EJECT
m 3 REW M# FF NTSC PB
x STOP X PAUSE COLOR SYSTEM
Z EJECT
DISPLAY
To set the colour system
If streaks appear during playback, set COLOR SYSTEM on the VCR to conform to the system that the tape was recorded in. (Normally set the switch to AUTO.)
If your tape was | Set COLOR SYSTEM to |
recorded in |
|
|
|
PAL | PAL/MESECAM |
|
|
NTSC | NTSC |
|
|
MESECAM | PAL/MESECAM |
|
|
To play an NTSC-recorded tape
Set NTSC PB on the VCR according to the colour system of your TV.
If your TV is | Set NTSC PB to |
PAL | ON PAL TV |
|
|
NTSC 4.43 | NTSC 4.43 |
|
|
NTSC 3.58 | NTSC 3.58 |
|
|
Turning on the VCR and TV to start playback (Trinitron TV Synchro Play)
You can only use this function if your TV is made by Sony (Trinitron TV).
How to connect to use this function
Connect the VCR and TV with the audio/ video cable. Be sure to connect the audio/ video cable to the VIDEO IN 1 jacks on the TV if the TV has two inputs or more. The TV must be placed where it will respond to the remote commander while you are pointing it at the VCR.
Operation
Make sure that the TV’s power is in standby mode.
Press TRINITRON TV SYNCHRO PLAY and hold the remote commander in place for about two seconds.
The VCR and TV turn on, and the TV is set to the video channel. If there is a tape in the VCR, playback starts automatically.
Notes
•If the Trinitron TV Synchro Play function does not work properly:
–Wait a few moments, and press the button again.
–Replace both of the batteries in the remote commander with new ones, and press the button again.
Note that this function may not operate some Sony TVs because of the remote commander’s signal limitations.
•Do not press TRINITRON TV SYNCHRO PLAY while playing back a video tape. If you do so, the TV’s input source will momentarily switch to the TV’s tuner.
3/# SEARCH
y SLOW X PAUSE
M FF
H PLAY x STOP
m REW
1 Turn on your TV and set it to the video channel.
2 Insert a tape.
The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed.
3 Press H PLAY (if playback did not start in step 2).
PLAY
When the tape reaches the end, it will rewind automatically.
Additional tasks
Playback options | Operation |
|
|
Stop play | Press xSTOP. |
|
|
Pause play | Press XPAUSE. |
|
|
Resume play after | Press XPAUSE or |
pause | ·PLAY. |
|
|
Press MFF (M#FF | |
| on the VCR) during stop. |
|
|
Rewind the tape | Press mREW |
| (m3 REW on the VCR) |
| during stop. |
|
|
View the picture | During |
during | hold M FF (M#FF on |
or rewind | the VCR) down. |
| During rewind, hold |
| mREW (m3REW |
| on the VCR) down. |
|
|
Play at high speed | • During playback or |
| pause, press |
| #SEARCH or |
| 3SEARCH. |
| • During playback or |
| pause, hold down |
| MFF (M# FF on |
| the VCR) or mREW |
| (m3 REW on the |
| VCR). |
| When you release the |
| button, normal |
| playback resumes. |
|
|
Play in slow motion | During playback or |
| pause, press y SLOW. |
|
|
To view the tape status on the screen
Press DISPLAY.
The following information appears on the TV screen.
LINE 1
STEREO
|
|
|
|
| Remaining |
|
|
|
|
| tape length |
|
|
|
|
|
|
SP | S– |
| E |
| Time counter |
0 : 0 0 : 22 |
| ||||
| |||||
Tape speed*
*Appears for a few seconds when the DISPLAY button is pressed and when the mode is changed.
To turn the display off, press DISPLAY again.
Notes
•The sound is muted during playback at various speeds and pause.
•You can eject a tape even when the power is off. When you press ZEJECT, the VCR turns on automatically. After ejecting the tape, the VCR turns off again.
•When the pause mode lasts for more than approximately five minutes, the VCR will automatically enter the playback mode.
•Tapes recorded in the LP mode of NTSC system on other VCRs can be played back on this VCR, but the picture quality cannot be guaranteed.
•The counter resets to “0:00:00” whenever a tape is inserted.
•The counter stops counting when it comes to a portion with no recording.
•If a tape has portions recorded in both PAL and NTSC systems, the time counter reading will not be correct. This is due to the difference between the counting cycles of the two colour systems.
•Streaks or snow cannot be eliminated completely in the various playback operations, especially in the slow motion mode.
•On screen symbols may shake while playing or searching at various speeds.
•Depending on your TV, the following may occur while playing an
–the picture is black and white,
–the picture shakes,
–no picture appears on the TV screen,
–black streaks appear horizontally on the TV screen, and
–the colour density increases or decreases.
Adjusting the picture
Although the VCR automatically adjusts the picture when playing a tape, distortions or noise may occur if the tape was recorded in poor condition. If so, manually adjust the resolution, colour and tracking.
RESOLUTION CONTROL II
buttons
STD PICT
AUTO/MANU
V/v NORMAL/ SLOW/STILL ADJUST
M/m/</, Resolution 
Control II
STANDARD
PICTURE
Adjusting the resolution and colour
1 While playing a tape, press M/m/</
,RESOLUTION CONTROL II (up/ down/left/right button on the unit) to display the RESOLUTION CONTROL II menu.
RESOLUTION CONTROL II
• • • • • C
• | • | • | • O |
• | • + | • | • L |
• • • • • O
•• • • • R RESOLUTION
The RESOLUTION CONTROL II buttons light up.
2 Press </,RESOLUTION CONTROL II (left/right button on the unit) to get a clearer picture.
3 Press M/m RESOLUTION CONTROL
II(up/down button on the unit) to get the best picture colour.
Wait for several seconds until the RESOLUTION CONTROL II menu disappears.
To resume the automatic adjustment
Press STANDARD PICTURE on the remote commander (STD PICT on the unit) so that
Adjusting the tracking
Press V/v TRACKING NORMAL/SLOW to obtain the best possible picture. The distortion should disappear as you press one of the two buttons. If you cannot get a clear picture with manual adjustment, press TRACKING AUTO/MANU to return to automatic adjustment.
About Adaptive Picture Control (APC)
Adaptive Picture Control (APC) automatically improves recording and playback quality by adjusting the unit to the condition of the video heads and tape.
APC playback
The APC function automatically works on all types of tapes, including rental tapes and tapes that were not recorded with APC.
APC recording
Whenever you insert a tape and first start recording, the unit adjusts to the tape using the APC function. This adjustment is retained until the tape is ejected.
Tip
•Adjust the picture using V/vNORMAL/ SLOW/STILL ADJUST if:
–streaks appear while playing in slow motion
–the picture shakes while pausing
Notes
•The auto tracking function works automatically when you play back a tape just after inserting it.
•There is a delay of a few seconds before the unit actually starts recording while the unit analyses the tape. To avoid the delay, first set the unit to recording pause and press zREC to have the unit analyse the tape. After ten seconds, press XPAUSE to start recording immediately. If you press X PAUSE before ten seconds, the APC function is cancelled.
•While playing a MESECAM recorded tape, you cannot adjust the colour using the RESOLUTION CONTROL II function.
•Sufficient picture quality may not be obtained when playing back tapes recorded on another VCR or tapes in poor condition.
•When a tape recorded with the copyguard system is played back, intermittent distortion may appear in the upper portion of the picture. However, this is not a malfunction of the unit.
Rewind and start play During stop, press H PLAY on the VCR while holding down
m3REW on the VCR.
Eject the tape | Press ZEJECT. |
Resume normal | Press HPLAY. |
playback |
|
|
|
the RESOLUTION CONTROL II buttons turn off.