|
| English |
|
|
|
|
|
| Français |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
F
Sports Pack
Main Feature
Useable at a depth of up to 3 m (9.8 feet) underwater.•This sports pack
•This sports pack is
Maintenance
•After recording in a location with a sea breeze, wash the sports pack thoroughly in fresh water with the buckles fastened to remove salt and sand, then wipe with a soft dry cloth. It is recommended that you submerge the sports pack in fresh water for about 30 minutes. If it is left with salt on it, metal portions may be damaged or rust may form and cause water leakage.
•If sun oil is on the sports pack, be sure to wash it off thoroughly using lukewarm water.
Troubleshooting
Symptom | Cause/Corrective Actions |
|
|
There are drops of water | • There are scratches or cracks on the |
inside the sports pack. | waterproof gasket. |
| b Replace the waterproof gasket with a new |
| one. |
| • The waterproof gasket is not set correctly. |
| b Place the waterproof gasket evenly in the |
Caractéristique principale
Utilisable jusqu’à une profondeur de 3 mètres (9,8 pieds) sous l’eau.•Le caisson étanche
•Ce caisson est étanche à l’eau, ce qui permet d’utiliser l’appareil photo numérique sous la pluie, la neige ou au bord de la plage.
Vous pouvez vous procurer des joints d’étanchéités et de la graisse chez votre revendeur Sony le plus proche.
Joint d’étanchéité (N° de modèle :
Graisse (N° de modèle :
Solution
Entretien
LRetrait de l’appareil photo numérique
1Mettez l’appareil hors tension.2Ouvrez le caisson.Vous pouvez facilement retirer l’appareil photo en le soulevant dans le sens de la flèche, comme indiqué sur l’illustration.
Lorsque l’appareil photo numérique a fonctionné pendant une longue période, il est relativement chaud. Mettez l’appareil photo numérique hors tension et
Operating Instructions
Mode d’emploi
Manual de instrucciones
Gebruiksaanwijzing
SPK-THA
© 2005 Sony Corporation Printed in Japan
Owner’s Record
The model and serial numbers are located inside of the unit. Record the serial number in the space provided below.
Refer to them whenever you call upon your Sony dealer regarding this product.
Model No.
A | Waterproof gasket |
| |
| Déclencheur |
C
D
G
1
2
3
H
W T |
| |
1 |
| |
Zoom button | Shutter button | |
Touche de zoom | Déclencheur | |
T |
| |
MENU |
| |
| POWER | |
Mode knob | button | |
Touche | ||
Sélecteur de | ||
POWER | ||
mode | ||
|
23
A loose or nipped waterproof gasket, sand or dirt on the waterproof gasket may cause water leaks under water. Be sure to check the waterproof gasket before use.
Notice•For using your digital still camera with this pack, refer to the operating instructions of the digital still camera.
•In the unlikely event that a malfunction of the sports pack causes damage due to water leakage, Sony does not guarantee against damages to the equipment contained in it (digital still camera, battery pack, etc.) and the recorded contents, nor expenses entailed in the photography.
Precautions
•Do not subject the front glass to strong shock, as it may crack.
•Avoid opening the sports pack at the beach or on the water. Preparation such as installing the digital still camera and changing the “Memory Stick Duo” should be done in a place with low humidity and no salty air.
•Do not throw the sports pack into the water.
•Avoid using the sports pack in places with strong waves. •Avoid using the sports pack under the following situations:
–in a very hot or humid place.
–in water hotter than 40 ˚C (104 ˚F).
–at temperatures lower than 0 ˚C (32 ˚F).
In these situations moisture condensation or water leakage may occur and damage the equipment.
•Use the sports pack for no longer than 30 minutes at a time in temperatures above 35 ˚C (95 ˚F).
•Be careful not to let the digital still camera fall when removing it from or putting it in the sports pack.
•Do not leave the sports pack under direct sunlight in a very hot and humid place for a long period of time. If you cannot avoid leaving the sports pack under direct sunlight, be sure to cover the pack with a towel or other protection.
•The digital still camera heats up if it is used inside the sports pack for a long time. Before removing the digital still camera from the sports pack, leave the sports pack in the shade or other cool place for a while to cool down.
•If sun oil is on the sports pack, be sure to wash it off thoroughly using lukewarm water. If the sports pack is left with sun oil on its body, the surface of the sports pack may become discolored or damaged (such as cracks on the surface).
Water leakageIf water happens to leak in, stop exposing the sports pack to water immediately.
If the digital still camera gets wet, take it to the nearest Sony dealer immediately. Repair costs must be borne by the customer.
Handling the waterproof gasket
What is the waterproof gasket?The waterproof gasket ensures the waterproof qualities of the sports pack or other equipment. (See illustration A)
Waterproof gasket maintenance is very important. Failure to carry out waterproof gasket maintenance according to the instructions may lead to water leakage and cause the sports pack to sink.
Handling the waterproof gasketFit the waterproof gasketAvoid fitting the waterproof gasket in dusty or sandy locations.
1Remove the waterproof gasket. (See illustration B)•You can easily remove the waterproof gasket by lifting it in the direction of the arrow as illustrated.
Be careful not to scratch the waterproof gasket with your fingernail. •Do not use a pointed or metal object to remove the waterproof gasket. This kind of object may scratch or damage the sports pack groove or
waterproof gasket.
2Inspect the waterproof gasket.•Check carefully for the following. If found, wipe off with a soft cloth or tissue paper.
–Is there any dirt, sand, hair, dust, salt, thread scraps, etc. on the waterproof gasket?
–Is there any old grease on the waterproof gasket?
•Clean the inside of the sports pack with a soft dry cloth. Do not wash the inside of the sports pack.
Be sure to perform the above maintenance each time you use the sports pack. Do not use any type of solvent such as alcohol, benzine or thinner for cleaning, as this might damage the surface finish of the sports pack.
When storing the sports pack•Attach the spacer supplied with your sports pack to prevent wear of the waterproof gasket. (See illustration E)
•Close the pack without fastening the buckles to prevent wear of the waterproof gasket.
•Prevent dust from collecting on the waterproof gasket.
•Avoid storing the sports pack in a cold, very hot or humid place, or together with naphthalene or camphor, as these conditions might damage the unit.
Preparation
Preparing the digital still camera
Install the digital still camera in a
For details, refer to the operating instructions supplied with the digital still camera.
1Remove the neck strap from the digital still camera.2If the stand is attached to the digital still camera, remove it.3Insert the battery pack.Be sure to use a fully charged battery pack.
4Insert the “Memory Stick Duo.”5Open the lens cover and turn on the power of the digital still camera.When opening the lens cover, be careful not to touch the lens.
6Set the LCD screen of the digital still camera to “ON.”Set the mode switch of the digital still camera to “ ” and then open the lens cover to turn on the digital still camera. The LCD screen comes “ON.”
7Set each of the settings on the digital still camera to “AUTO” mode.8Set the AF illuminator on the digital still camera to “OFF.”This disables use of the AF illuminator.
9Check the digital still camera’s lens and LCD screen for any dirt.FAttach the hand strapWe recommend attaching the hand strap (supplied) before using the sports pack. (See illustration F)
Notes•Be careful not to pinch the hand strap when you open and close the sports pack body. Water may leak in if you do.
•The float attached to the hand strap is for preventing loss of the sport pack underwater. Use the hand strap with the float attached.
GInstalling the digital still camera inside the sports pack
1Set the POWER button of the dgital still camera to “OFF.”Set the mode button of the digital still camera to “.”
2Open the sports pack.Keep the lock release button 1 pressed down, turn the buckle dial 2 and open the buckle in the direction of the arrow 3.
3Prepare the sports pack.Be sure to read the separate “Handling the waterproof gasket”. Important details regarding maintenance and handling of the waterproof gasket are described in this manual.
1Remove the waterproof gasket.
2Coat the waterproof gasket with grease.
Clean off any sand or dirt on the waterproof gasket, in the seating groove, or on the sports pack’s body where it touches the waterproof gasket. Coat the waterproof gasket with a light, even layer of grease.
3Fit the waterproof gasket.
NoteThe sports pack’s body may be scratched or water may leak if the cover is closed with sand or dirt on the waterproof gasket.
4 Install the digital still camera inside the sports pack.Leave the lens cover of the digital still camera open. Forcing the sports pack closed while the lens cover is closed can lead to a malfunction.
| groove. |
| • The buckle is not fastened. |
| b Fasten the buckle until it clicks. |
The recording function does | • The battery pack has run out. |
not work. | b Charge the battery pack fully. |
| • The “Memory Stick Duo” is full. |
| b Insert another “Memory Stick Duo” or |
| erase unneeded data from the “Memory |
| Stick Duo.” |
| • The |
| Duo” is set to LOCK. |
| b Set the tab to the recording position or |
| insert a new “Memory Stick Duo.” |
|
|
|
|
|
|
Specifications
MaterialPlastic (PC, ABS), stainless steel, glass
Waterproof gasket, buckle
To a depth of up to 3 m (9.8 feet) underwater
Switches that can be externally operatedPower, Mode, Shutter, Zoom, Flash, Macro, Control,
Approx. 122 ⋅ 75 ⋅ 28 mm (4 7/8 ⋅ 3 ⋅ 1 1/8 inches) (w/h/d) (excluding projecting parts)
MassApprox. 110 g (3.9 oz) (sports pack only)
Included itemsSports pack (1)
Hand strap (1)
Float (1)
Grease (1)
Spacer (1)
Set of printed documentation
Design and specifications subject to change without notice.
Un joint d’étanchéité relâché ou pincé ou la présence de sable ou de saletés sur le joint peut entraîner des infiltrations d’eau. Vérifiez le joint d’étanchéité avant d’utiliser l’équipement.
Avertissement•Pour utiliser votre appareil photo numérique avec ce caisson, reportez- vous au mode d’emploi de l’appareil photo.
•Dans le cas très improbable où une anomalie du caisson causerait des dommages dus à une infiltration d’eau, notez que la garantie Sony ne couvre pas les dommages subis par le matériel (appareil photo numérique, batterie, etc.) à l’intérieur du caisson, le contenu enregistré ou les frais encourus pour la prise de vues.
Précautions
•Ne soumettez pas le verre avant à des chocs importants, car il pourrait se craqueler.
•N’ouvrez pas le caisson sur la plage ou dans l’eau. Les opérations préparatoires, telles que la mise en place de l’appareil photo numérique et le changement de « Memory Stick Duo », doivent être effectuées à l’abri de l’humidité et de l’air salin.
•Ne jetez pas le caisson dans l’eau. •N’utilisez pas le caisson par fortes vagues.
•N’utilisez pas le caisson dans les conditions suivantes :
–dans un endroit très chaud ou humide.
–dans de l’eau chaude à plus de 40 °C (104 °F).
–à des températures inférieures à 0 °C (32 °F).
Dans de telles conditions, le matériel pourrait être endommagé par une condensation ou une infiltration d’eau.
•N’utilisez pas le caisson plus de 30 minutes d’affilée par une température supérieure à 35°C (95 °F).
•Prenez garde à ne pas faire tomber l’appareil photo numérique lorsque vous le retirez et que vous le remettez dans le caisson.
•Ne laissez pas le caisson en plein soleil ou dans un endroit très chaud et humide pendant une longue période. Si vous n’avez pas d’autre choix que de le laisser en plein soleil,
•L’appareil photo numérique s’échauffe s’il est utilisé pendant longtemps à l’intérieur du caisson. Avant de retirer l’appareil photo numérique du caisson, laissez temporairement le caisson à l’ombre ou dans un endroit frais pour qu’il se refroidisse.
•S’il y a de la crème solaire sur le caisson, prenez soin de l’éliminer convenablement avec de l’eau tiède. Si la surface du boîtier du caisson est souillée avec de la crème solaire, elle risque de se décolorer et de s’endommager (craquelures sur la surface).
Infiltration d’eauSi de l’eau s’infiltre dans le caisson, arrêtez immédiatement de l’exposer à l’eau.
Si l’appareil photo numérique est mouillé,
Manipulation du joint d’étanchéité
Le joint d’étanchéité garantit l’étanchéité du caisson ou de tout autre équipement. (Voir illustration A)
L’entretien du joint d’étanchéité est très important. Le
N’installez pas le joint d’étanchéité dans des endroits sablonneux ou poussiéreux.
1 Retirez le joint d’étanchéité. (Voir illustration B) |
•Vous pouvez facilement retirer le joint d’étanchéité en le soulevant |
dans le sens de la flèche indiquée sur l’illustration. |
Prenez garde à ne pas érafler le joint d’étanchéité avec vos ongles. |
•N’utilisez pas d’objet pointu ou métallique pour retirer le joint |
d’étanchéité. |
Ce type d’objet risque d’érafler ou d’endommager la rainure du |
caisson ou le joint d’étanchéité. |
2 Inspectez le joint d’étanchéité. |
•Vérifiez les points suivants. En cas d’anomalie, nettoyez le joint à l’aide |
•Après une prise de vues dans un endroit exposé à la brise marine, lavez soigneusement le caisson à l’eau douce avec les fermoirs correctement verrouillés pour en retirer le sel et le sable, puis
•S’il y a de la crème solaire sur le caisson, prenez soin de l’éliminer convenablement avec de l’eau tiède.
•Nettoyez l’intérieur du caisson avec un chiffon doux et sec. Ne lavez pas l’intérieur du caisson.
Effectuez les opérations d’entretien
•Fixez l’entretoise fournie avec votre caisson pour protéger le joint d’étanchéité contre l’usure. (Voir illustration E)
•Fermez le caisson sans verrouiller les fermoirs pour protéger le joint d’étanchéité contre l’usure.
•Empêchez l’accumulation de poussière sur le joint d’étanchéité.
•Ne rangez pas le caisson dans un endroit froid, très chaud ou humide ou avec de la naphtaline ou du camphre. Ceci pourrait l’endommager.
Préparation
Préparation de l’appareil photo numérique
Installez l’appareil photo numérique autant que possible dans un endroit peu humide. En effet, l’ouverture ou la fermeture du caisson dans un endroit chaud ou humide peut provoquer la formation de buée sur le verre avant.
Pour plus d’informations,
Utilisez une batterie complètement rechargée.
4Insérez le « Memory Stick Duo ».5Ouvrez le couvercle d’objectif et mettez l’appareil photo sous tension.Lorsque vous ouvrez le couvercle d’objectif, attention de ne pas toucher l’objectif.
6Réglez l’écran LCD de l’appareil photo sur « ON ».Réglez le sélecteur de mode de l’appareil photo sur « » et ouvrez le couvercle d’objectif pour mettre l’appareil photo sous tension. L’écran LCD s’allume.
7Réglez toutes les fonctions de l’appareil photo numérique en mode « AUTO ».8Réglez l’éclairage AF de l’appareil photo numérique sur « OFF ».Ceci désactive l’éclairage AF.
9
Il est recommandé d’attacher la dragonne (fournie) avant d’utiliser le caisson. (Voir illustration F)
Remarques•Prenez garde à ne pas coincer la dragonne lorsque vous ouvrez ou fermez le boîtier du caisson. L’eau risquerait de pénétrer à l’intérieur.
•Le flotteur fixé à la dragonne évite de perdre le caisson étanche lors de la plongée. Utilisez toujours la dragonne avec son flotteur.
GMise en place de l’appareil photo numérique dans le caisson
1Réglez la touche POWER de l’appareil photo sur « OFF ».Réglez le sélecteur de mode de l’appareil photo sur « ».
2Ouvrez le caisson.Laissez la touche d’ouverture 1 enfoncée, tournez la molette à boucle 2 et ouvrez la boucle dans le sens de la flèche 3.
3Préparez le caisson.Veillez à lire la section « Manipulation du joint d’étanchéité », car elle renferme des informations importantes sur l’entretien et la manipulation du joint d’étanchéité.
1Retirez le joint d’étanchéité.
2Enduisez le joint d’étanchéité de graisse. |
Enlevez le sable et autres saletés présents sur le joint d’étanchéité, sur |
Essuyez soigneusement le caisson et
En cas de problème
Symptôme | Cause/Remèdes |
|
Présence de gouttes d’eau à | • Le joint d’étanchéité est éraflé ou craquelé. |
|
l’intérieur du caisson | b |
|
| • Le joint d’étanchéité n’est pas correctement |
|
| disposé. |
|
| b |
|
| rainure. |
|
| • Le fermoir n’est pas verrouillé. |
|
| b |
|
| s’encliquette. |
|
La fonction d’enregistrement | •La batterie est épuisée. |
|
ne fonctionne pas | b |
|
| • Le « Memory Stick Duo » est saturé. |
|
| b Insérez un autre « Memory Stick Duo » ou |
|
| effacez les données inutiles du « Memory |
|
| Stick Duo ». |
|
| • Le taquet de protection en écriture du |
|
|
| |
| « Memory Stick Duo » est réglé sur LOCK. |
|
| b Réglez le taquet sur la position |
|
|
| |
| d’enregistrement ou insérez un « Memory |
|
| Stick Duo » neuf. |
|
|
|
|
|
|
|
|
|
|
Spécifications
MatièrePlastique (PC, ABS), acier inoxydable, verre
Etanchéité à l’eauJoint d’étanchéité, fermoir
Résistance à la pressionJusqu’à une profondeur de 3 m (9,8 pieds) sous l’eau
Commutateurs pouvant être commandés de l’extérieurAlimentation, Mode, Déclencheur, Zoom, Flash, Macro, Commande, Retardateur, Revue, Menu, Taille de l’image/Suppression, Etat LCD/Marche/ Arrêt LCD
Dimensions122 ⋅ 75 ⋅ 28 mm (4 7/8 ⋅ 3 ⋅ 1 1/8 po.) (l/h/p) environ (parties saillantes non comprises)
Poids110 g (3,9 on.) (caisson uniquement)
Articles inclusCaisson (1)
Dragonne (1)
Flotteur (1)
Graisse (1)
Solution
Entretoise (1)
Jeu de documents imprimés
La conception et les spécifications sont sujettes à modification sans préavis.
E |
|
|
| 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| I |
|
|
| (LCD status/LCD on/off) | ||
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| MENU button | button |
|
| |
|
|
|
| (flash)button/ | Touche | (Etat LCD/ | ||||
|
|
|
| Touche MENU | Marche/Arrêt LCD) |
| ||||
|
|
|
| Control button |
|
|
|
|
| |
|
|
|
| Touche | (flash)/ |
|
|
|
|
|
|
|
|
| Touche de |
|
|
|
|
|
|
|
|
|
| commande |
| MENU |
|
|
| |
|
|
|
| (review)button |
|
|
|
|
| |
Shutter button |
| Zoom button |
| /Control button |
|
|
|
|
| |
|
| Touche |
|
|
|
|
|
| ||
Déclencheur |
| Touche de zoom |
|
|
|
|
|
| ||
| (Revue)/Touche de |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| ||
|
|
|
| commande |
|
|
|
|
| |
|
|
|
| Enter/Control button |
|
|
| (Image Size/ | ||
|
|
|
|
|
| Delete) button |
| |||
|
|
|
| Validation/Touche de |
|
|
| |||
|
|
|
|
|
| Touche | (Taille de | |||
|
|
|
| commande |
|
|
| |||
|
|
| Front glass |
|
|
| l’image/Suppression) | |||
|
|
|
|
| ||||||
|
|
|
|
| (Macro)button/ |
| ||||
|
|
| Verre avant |
|
|
| ||||
|
|
|
| Control button |
|
| Control button |
| ||
|
|
| Buckle dial | Touche | (Retardateur)/ |
| Touche | (macro)/ |
| |
|
|
| Molette à | Touche de commande |
|
| Touche de commande | |||
|
|
| boucle |
|
|
|
|
|
|
|
|
|
|
| J |
|
|
|
|
|
|
Mode knob |
|
|
|
| 1 | W T | 2 |
|
| |
|
|
|
|
|
|
|
|
|
| |
Sélecteur de |
| T |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
mode |
|
|
|
|
|
|
|
|
|
|
MENU button | MENU |
|
| K |
|
|
|
|
|
|
Touche MENU |
|
| POWER button |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
|
|
| Touche POWER | 1 |
|
| 2 1 |
|
|
|
Control button |
|
| Hook for hand |
|
|
|
| 2 | ||
|
|
|
|
|
|
|
|
| ||
Touche de commande |
|
|
|
|
|
|
|
| ||
| strap |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
(Image Size/Delete) |
| Crochet pour |
|
|
|
|
|
|
| |
| dragonne | L |
|
|
|
|
|
| ||
button |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
Touche | (Taille de | (LCD status/LCD on/ |
|
|
|
|
|
| ||
l’image/Suppression) | 1 |
|
|
|
|
|
| |||
off) button |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| ||
|
| Touche | (Etat LCD/ |
|
|
|
|
|
| |
|
| Marche/Arrêt LCD) |
|
|
|
|
|
|
| |
Spacer |
| Waterproof gasket |
|
|
|
|
|
|
| |
Entretoise |
| Joint d’étanchéité |
|
|
|
|
|
|
|
2
Printed on 100% recycled paper using VOC (Volatile Organic
•Lightly run your fingertip around the waterproof gasket to check for any invisible dirt.
•Be careful not to leave any cloth or tissue paper fibers on the waterproof gasket after wiping it.
•Check the waterproof gasket for cracks, skewing, distortion, fine splitting, scratches, sand inclusion, etc. Replace the waterproof gasket if it is cracked or scratched.
v Cracks v Skewing v Distortion v Fine v Scratches v SandSplittinginclusion3Inspect the waterproof gasket groove.Grains of sand or hardened salt sometimes get into the groove. Carefully remove them by blowing with an air spray or by wiping them with a cotton wool bud. Be careful not to leave any fibers from the cotton wool bud inside.
4Inspect the contact surface on the other side of the waterproof gasket in the same way.
5Apply a coating of grease to the waterproof gasket.•Use your fingertips to thinly coat the entire surface of the waterproof gasket with a small drop of grease. (See illustration C)
•Do not use paper or cloth as fibers may stick to the waterproof gasket. •Make sure there is always a thin coating of grease on the surface of the waterproof gasket. Grease protects the waterproof gasket and prevents
wear.
•Fit the waterproof gasket immediately after coating it with grease. Do not leave the greased waterproof gasket on a table or other surface.
6Fit the waterproof gasket into the groove of the sports pack.Fit the waterproof gasket evenly into the groove paying attention to the following points:
–Check for dirt on the waterproof gasket.
–Check the waterproof gasket is not twisted. (See illustration D)
How to check for water leakageAfter replacing the waterproof gasket, close the sports pack without inserting the equipment you are going to use. Immerse the sports pack in water to a depth of about 15 cm for about three minutes and check that no water leaks in.
MaintenanceIf the sports pack is allowed to dry with sea water still in the waterproof gasket groove, salt crystals form which may impair the waterproof gasket’s functions.
Waterproof gasket serviceable lifeThe serviceable life of the waterproof gasket varies with frequency of use of the sports pack and conditions. Generally, it is about one year.
Even if the waterproof gasket is not cracked or scratched, deformation or wear reduces its waterproof qualities. Replace the waterproof gasket with a new one if you find cracks, skewing, distortion, fine splitting, scratches, sand inclusion, etc.
After replacing, check that no water leaks in.
GreaseUse the grease supplied. Using other manufacturer’s grease will damage the waterproof gasket, and cause water leaks.
Coat the surface of the glass with the supplied
Apply 2 or 3 drops of the liquid to the front glass and wipe evenly to spread the liquid out by using the swabs, a soft cloth or tissue paper.
Waterproof gasket, grease andYou can obtain the waterproof gasket and grease at the nearest Sony dealer. Waterproof gasket (model No.
Grease (model No.
Check that the digital still camera is placed correctly.
5Close the sports pack’s body and fasten the buckle.Secure the sports pack’s body, and fasten the buckle until it clicks.
Using the Sports Pack
HRecording (See illustration H-1)
1Turn on the power. Check that the Mode knob operates normally.
For details of each mode, check in the LCD screen.
2Set the Mode knob to the desired mode.You can record pictures while looking at the LCD screen.
To record still images, set the Mode knob of the sports pack to “”.
To record moving images, set the Mode knob of the sports pack to “”. Sound cannot be recorded while recording moving images.
For details, refer to the operating instructions supplied with the digital still camera.
3Press the shutter button.You can use the various functions of the digital still camera installed in the sports pack.
JUse the zoomSlide the zoom button. (See illustration J)
1Press on the W side for
2 Press on the T side for telephoto. (Subject appears closer.)
Note
If you do not operate the digital still camera with the power on for a certain time, the digital still camera turns off automatically to prevent the battery pack from wearing down. To use the digital still camera again, turn on the power again. For details, refer to the operating instructions supplied with the digital still camera.
KPlaying back with the control button
You can play back images on the LCD screen using the control button. You cannot hear the sound.
1Turn on the power.2Set the Mode knob to “”.LRemoving the digital still camera
1Turn off the power.2Open the sports pack.You can easily remove the digital still camera by lifting it in the direction of the arrow as illustrated.
When the digital still camera has been used for a long time, the digital still camera heats up. Turn off the power and leave for a while to cool down before removing the digital still camera from the sports pack.
Be careful not to drop the digital still camera when removing it.Note
Carefully wipe any water off the sports pack and your body before opening the sports pack so that no drops get onto the digital still camera.
d’un chiffon doux ou d’un mouchoir en papier. |
– Présence de saletés, de sable, de cheveux, de poussière, de sel, de |
particules, etc. |
– Présence de graisse. |
•Passez légèrement votre doigt sur le joint d’étanchéité pour détecter d’éventuelles saletés invisibles.
v Craquelures v Torsion v Déformation v Fine | v Eraflures v Incrustation |
coupure | de sable |
Des grains de sable ou de sel s’incrustent parfois dans la rainure.
4Inspectez de la même manière la surface de contact de l’autre côté du joint d’étanchéité.
5Appliquez une couche de graisse sur le joint d’étanchéité.•Avec les doigts, enduisez légèrement toute la surface du joint d’étanchéité d’une petite goutte de graisse. (Voir illustration C)
•N’utilisez pas de mouchoir en papier ni de tissus, car les fibres risquent de coller au joint d’étanchéité.
•Veillez à ce qu’il y ait toujours une fine couche de graisse sur la surface du joint d’étanchéité. La graisse protège le joint et prévient l’usure.
•Fixez le joint d’étanchéité immédiatement après l’avoir enduit de graisse. Ne posez pas le joint enduit de graisse sur une table ou une autre surface.
6Fixez le joint d’étanchéité dans la rainure du caisson.Fixez le joint uniformément dans la rainure, en respectant les points suivants :
–Vérifiez qu’il n’y a pas de saletés sur le joint d’étanchéité.
–Vérifiez que le joint d’étanchéité n’est pas tordu. (Voir illustration D)
Vérification de l’absence de défauts d’étanchéitéAprès avoir replacé le joint d’étanchéité, fermez le caisson sans insérer l’équipement que vous allez utiliser. Plongez le caisson dans l’eau à une profondeur d’environ 15 cm pendant trois minutes environ et
Si vous faites sécher le caisson alors que la rainure du joint d’étanchéité contient encore de l’eau de mer, des cristaux de sel vont se former et peuvent diminuer l’étanchéité.
Durée de service du joint d’étanchéitéLa durée de service du joint d’étanchéité varie selon la fréquence d’utilisation du caisson et les conditions d’entreposage. Elle est généralement d’une année environ.
Même si le joint d’étanchéité n’est pas craquelé ni éraflé, la déformation ou l’usure réduit ses qualités d’étanchéité. Remplacez le joint d’étanchéité par un neuf s’il est craquelé, déformé, tordu, coupé, éraflé, incrusté de sable.
Une fois le remplacement effectué, vérifiez qu’il n’y a aucune infiltration d’eau.
GraisseUtilisez la graisse fournie. L’emploi de la graisse d’un autre fabricant endommagerait le joint d’étanchéité et entraînerait des infiltrations d’eau.
SolutionEnduisez la surface du verre avec la solution
Appliquez 2 ou 3 gouttes du liquide sur le verre avant et étalez uniformément pour répandre le liquide à l’aide de disques de coton, d’un chiffon doux ou d’un mouchoir en papier.
la rainure du joint ou sur la surface du boîtier entrant en contact avec |
le joint d’étanchéité. Enduisez le joint d’étanchéité d’une légère |
couche uniforme de graisse. |
3Fixation du joint d’étanchéité.
Remarque
Le boîtier du caisson risque d’être éraflé et de l’eau pourrait s’infiltrer si le couvercle est refermé alors que du sable ou de la saleté se trouve sur le joint d’étanchéité.
4 Installez l’appareil photo numérique dans le caisson.Laissez le couvercle d’objectif de l’appareil photo numérique ouvert. Ne pas essayer de maintenir fermé le couvercle d’objectif quand il s’ouvre car il pourrait être endommagé.
Tenez bien le boîtier du caisson et bouclez le fermoir jusqu’à ce qu’il s’encliquette.
Utilisation du caisson
HPrise de vues (Voir illustration H-1)
1Mettez l’appareil sous tension. Lorsque vous faites glisser le sélecteur de mode, le mode change dans l’ordre suivant :
Pour plus d’informations sur chaque mode, consultez l’écran LCD.
2Réglez le sélecteur de mode sur la position appropriée.Vous pouvez enregistrer des images tout en regardant l’écran LCD.
Pour enregistrer des images fixes, réglez le sélecteur de mode du caisson sur « ».
Pour enregistrer des images animées, réglez le sélecteur de mode du
caisson sur « ».
Il est impossible d’enregistrer des sons en même temps que des images animées.
Pour plus d’informations,
Vous pouvez utiliser les diverses fonctions de l’appareil photo numérique lorsqu’il est installé dans le caisson.
JUtilisation du zoomFaites glisser la touche de zoom. (Voir illustration J)
1Appuyez sur le côté W pour une prise de vues grand angle. (Le sujet s’éloigne.)
2Appuyez sur le côté T pour une prise de vues au téléobjectif. (Le sujet se rapproche.)
Remarque
Si vous n’utilisez pas l’appareil photo un certain temps après l’avoir mis sous tension, il s’éteindra automatiquement pour empêcher la batterie de s’user. Pour utiliser de nouveau l’appareil photo numérique,
KLecture à l’aide de la touche de commande
Vous pouvez visionner des images sur l’écran LCD à l’aide de la touche de commande. Le son n’est pas audible.
1Mettez l’appareil sous tension.2Réglez le sélecteur de mode « ».