Getting Started

HookupOverview

The amplifier allows you to connect and control the following audio components. Follow the hookup procedure indicated for each component that you want to connect.

To learn the location and name of each jack, see “Rear Panel Descriptions” on page 11.

DAT deck

 

 

 

 

Tape deck

Tuner

 

MD deck

 

 

 

 

Turntable

CD player

PROTECTION

 

 

 

 

 

 

 

 

INPUT SELECTOR

VOLUME

 

 

 

 

 

 

 

 

 

 

 

 

U

 

 

 

 

 

 

 

 

 

 

 

g

 

 

 

 

 

 

 

 

 

 

 

EON LINK

TAPE1/DAT

TAPE2/MD

 

AUX

 

CD

 

TUNERPHONO

 

 

 

EON LINK

SPEAKERS

BASS

TONE

TREBLE

 

 

BALANCE

 

TAPE MONITOR

 

 

 

A

0

 

0

 

 

 

 

 

SOURCE DIRECT

 

 

OFF • B

 

 

 

LOUDNESS SUBSONIC

SOURCE

0

10

 

A+B

 

 

 

 

 

 

Ø ON ø OFF ØON ø OFF

TAPE1 • TAPE2

 

 

PHONES

 

 

 

 

 

 

 

 

 

 

 

 

10

+10 10

+10

LEFT

RIGHT

 

 

 

Speaker (L)

 

 

 

TV or video

Speaker (R)

 

 

 

 

deck

 

 

 

 

 

 

 

 

 

 

Before you get startedTurn off the power to all components before making any connections.

Do not connect the mains leads of the various components until all connections are completed.

Use the audio connecting cords supplied with each component for hooking up with the amplifier. Purchase and use optionally available cords as required.

Be sure to make connections firmly to prevent hum and noise.

When connecting an audio connecting cord, be sure to match the R (right) and L (left) jacks of the amplifier to the R and L jacks on the other

components.

AudioComponentHookups

OverviewHere you learn how to connect your audio components to the amplifier.PHONO y AUX TAPE1/DAT

PHONO

 

 

 

 

 

 

 

IMPEDANCE USE 4–16Ω

IN

 

SIGNAL

 

 

 

 

 

 

GND

 

 

 

 

A+B USE 8–16Ω

L

 

y

 

 

 

 

 

BI WIRE USE 4–16Ω

 

 

 

 

 

SPEAKERS

 

 

 

 

 

 

 

 

 

 

 

R

 

 

 

 

+

R

L

+

 

 

 

 

 

B

 

 

 

 

 

L

 

 

 

 

L

 

 

 

 

EON CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

R

 

 

 

 

R

 

 

 

 

 

IN

IN

IN

REC OUT IN

REC OUT IN

+

R

L

+

TUNER

CD

AUX

TAPE2/MD

TAPE1/DAT

 

 

 

 

 

IN

TUNER CD TAPE2/MD EON CONTROL INWhat cords will I need?

Audio connecting cord (not supplied) (2 for each tape deck, DAT deck, or MD deck; 1 for other components)

White (L)

White (L)

Red (R)

Red (R)

HookupsThe arrow çindicates signal flow.CD playerAmplifierCD player

L

Ç

L

 

R

 

R

IN

 

LINE

CD

 

OUTPUT

Tuner

 

 

Amplifier

 

Tuner

L

Ç

L

 

R

 

R

IN

 

LINE

TUNER

 

OUTPUT

4GB