Sony XT-V70 Specifications, 更換前支柱壓條, 4 5 UW, BDD, )qs, ACC, )qd, QBM, PAL, DDJS, CCIR, 3.23)WIG, 2-12(VHF), 32.7:)VIG, 21-69(UHF), 2.23)WIG, 1-12(VHF), 24.68)VIG

Protective sheet

保護膜

TV aerial amplifier unit 4

電視天線放大器 4 4

TV aerial amplifier unit 4

電視天線放大器 4 4

Fold back the floor mat. 將底板墊向後折。

Peel off the protective sheet. 撕下保護膜。

Attach the power supply terminal to the film aerial 5 (9)1Remove the power supply point protective sheet from the film aerial (9-1).

The color of the protective sheet is used to distinguish the left and right aerials.

The right aerial (as seen from inside the car) has a blue protective sheet, and the left aerial has a white protective sheet. Take care to mount the aerials on the proper side of the car.

2Attach the aerial input cable 6 to the film aerial power supply terminals (9-2).

•The same type of cable is used for both the left and right aerials.

•Temporarily fastening the cable near the ground connection with cellophane tape will make the procedure easier.

Connecting to the power supply terminals

Align the protrusions on the power supply terminals with the arrows v on the film aerial and fasten in place.

Alignment marks (protrusions)

Specifications

Reception format	PAL
Channels	CCIR
	2 – 12 (VHF)
	21 – 69 (UHF)
	China
	1 – 12 (VHF)
	13 – 57 (UHF)
	UK/HKG (Hong Kong)
	– (VHF)
	21 – 69 (UHF)
	Newzealand
	1 – 11 (VHF)
	21 – 69 (UHF)
	Australia
	0 – 12 (VHF)
	28 – 69 (UHF)
Power requirement	(Monaural)
Power requirement	12 V DC
Power consumption	(negative ground)
Power consumption	240 mA
Inputs	Video (1)

安裝電源端子到薄膜天線 5 上 (9)		5 )9*
1 撕下薄膜天線上的電源觸點保護膜(9-1)。	1	)9-1*
保護膜上的顏色用於區分左右天線。
右側天線（從車內看）是藍色保護膜，左側天線是白色保護
膜。請注意把天線安裝到汽車上正確的一側。
2 把天線輸入電纜 6 安裝到薄膜天線電源端子(9-2)。	2	6	)9-2*
•左側和右側天線使用相同類型的電纜。		•
•使用透明膠臨時把電纜固定在接地連接附近，這樣可以使整個		•
過程更簡單。
連接到電源端子
把電源端子上的突起部分與薄膜天線上的箭頭 v 對準後把它固定到位。		v
對準標記
（突起部分）		)	*
電源端子
對準標記（箭頭 v)		)	v*

Temporary fastening (cellophane tape, etc.) 臨時固定（透明膠等）

) *

Power supply point	Power supply point
電源觸點	電源觸點

Peel off the	Peel off the
protective	protective
sheet.	sheet.
撕下保護膜。	撕下保護膜。

Temporary fastening (cellophane tape, etc.)

臨時固定（透明膠等）

) *

Aerial contacts

天線觸點

Spare contact

備用觸點

Ground contact

接地觸點

Vehicle ACC power supply

車載 ACC 電源

BDD

Power supply terminals

Alignment marks (arrows v)

3Pass the aerial input cable 6 through the roof lining (inner roof panel) (9-3).

Notes

•Pull the roof lining down slightly and thread the cable under it.

•Take care not to pull too hard on the lining and bend it out of shape.

•Perform this step while holding on to the power supply point to avoid putting stress on that point.

•Route the aerial input cable carefully to avoid pulling excessively on, applying stress to, or kinking the cable.

Route the aerial input cable 6 (0)

	Bus (1)
Outputs	TV aerial (4)
Outputs	Video (1)
	Bus (1)
Dimensions	Approx. 127 ⋅ 30 ⋅ 107 mm
	(5 ⋅ 1 3/16 ⋅ 4 1/4 in.)
Mass	(W ⋅ H ⋅ D)
Mass	Approx. 0.38 kg (13 oz)

Design and specifications are subject to change without notice.

3	把天線輸入電纜 6 穿過內頂板（9-3）。	3	6	)9-3*
注意
• 把內頂板輕輕往下拉，並從下面穿過。		•
• 小心不要過分拉內頂板和將其彎曲變形。		•
• 執行此步時要拿住電源觸點防止壓力加到觸點上。		•
• 小心排布天線輸入電纜，避免硬拉、加力或打結。		•
天線輸入電纜 6 佈線(0)			6 )0*
1	把接地膠帶 7 貼到車身上（0-1）。	1	7	)0-1*
	把接地膠帶貼到車身的金屬上，在該點可以連接天線輸入電纜
	的接地觸點。
	注意
	• 小心擦去安裝表面的灰塵。		•
	• 請務必把接地膠帶粘貼到車身的平坦金屬部位。切勿把接地膠帶粘到不		•
	平坦的位置或夾子、螺絲孔的上方。不要刮擦車身的油漆。
2	把天線輸入電纜上的接地觸點粘到接地膠帶 7 上。	2		7
	撕下接地觸點上的保護膜並把觸點完全粘到接地膠帶上。確保
	接地觸點沒有任何部分露在接地膠帶外面，且接地觸點的所有
	部分都牢固地粘到接地膠帶上。
3	使用隨機提供的天線電纜夾 9 為天線輸入電纜佈線，將它固	3		9

Roof lining

內頂板

Grounding tape 7 (peel off the protective sheet) 接地膠帶 7 (撕下保護膜)

7)*

Ground contact (peel off the protective sheet)

接地（撕下保護膜）

) *

Aerial cord clamp 9

天線電纜夾 9

Aerial cord clamp 9 天線電纜夾 9

Aerial input cable (right) 6

天線輸入電纜（右）6 ) *6

4		Aerial input cable (left) 6
4		天線輸入電纜（左）6
		天線輸入電纜（左）6
	Aerial cord clamp 9	) *6
	Aerial cord clamp 9
	天線電纜夾 9
	9

Aerial cord clamp 0

天線電纜夾 0

IMPORTANT CAUTION! Do not route the cable near the pedals!

重要的注意事項！

不要在踏板附近佈線！

qd	Front pillar	Front pillar
	前支柱	前支柱
	Film aerial (left) 5	Film aerial (right) 5
	薄膜天線（左）5	薄膜天線（右）5
	) *5	) *5

Aerial input cable (left) 6	XAV-A1	Aerial input cable (right) 6
天線輸入電纜（左）6	XAV-A1	天線輸入電纜（右）6
) *6		) *6

TV aerial amplifier unit 4

電視天線放大器 4 4

1Apply the grounding tape 7 to the car body (0-1). Apply the grounding tape to the metal of the car body, in a position where it can contact the ground contact on the aerial input cable.

Notes

•Carefully wipe away any dirt on the attachment surface.

•Be sure to stick the grounding tape completely to a flat, metal part of the car body. Do not apply the grounding tape to a place that is not flat, or over a clip or screw hole. Do not scrape off the finish on the car body.

2Affix the ground contact on the aerial input cable to the grounding tape 7.

Peel off the protective sheet from the ground contact and stick it completely to the grounding tape. Make sure that no portion of the ground contact protrudes beyond the grounding tape, and that there is no part of the ground contact which is not firmly stuck to the grounding tape.

3Route the aerial input cable, using the supplied aerial cord clamp 9 to hold it in place (0-2,3,4).

Route the cable so that it will be completely covered when the front pillar molding is replaced.

Important note

Use tape or other fasteners to route the cables such that they cannot interfere with vehicle operation. Do not wrap the cables around the steering column, gear shift lever, brake pedal, etc.

Mount the TV aerial amplifier unit 4 (qa)

1Mount the TV aerial amplifier unit near the floor in the foot area in front of the passenger’s seat. (Be sure to wipe away any dirt on the mounting surface.)

Important note

It would be extremely dangerous if the TV aerial amplifier unit were to get stuck underneath the brake pedal. Be sure to mount the amplifier on the passenger’s side.

2Connect the grounding cable from the TV aerial amplifier unit to a metal part of the car body where it can make a good ground contact.

3Connect the aerial input cables to the TV aerial amplifier unit according to the markings on the amplifier (1, 2, 3, 4, TV).

Connect the TV tuner unit and the car’s ACC power supply (qs)

1Connect the aerial terminal (L-type) on the TV aerial amplifier unit 4 to the TV tuner unit.

2Connect the accessory power supply terminal to the car’s ACC power supply.•Connect the ACC power supply cord from the TV tuner unit to the spare contact.•Do not connect directly to the battery.Replace the front pillar moldingFasten cords out of the way (qd)

	定到位（0-2,3,4）。		0-2,3,4
	電纜佈線時要做到更換前支柱壓條時能完全覆蓋。
	重要事項
	使用膠帶或其他固定件佈線時要不影響汽車的操作。不要把電纜繞在駕
	駛杆、變速杆、剎車踏板等上面。
安裝電視天線放大器 4(qa)			4)qa*
1	把電視天線放大器安裝在副駕駛座位前面的腳部區域的地板附	1
	近。（務必要擦去安裝表面的灰塵。）
	重要事項
	如果把電視天線放大器粘在剎車踏板下面是非常危險的。請務必把放大
	器安裝副駕駛側。
2	從電視天線放大器到車身上能良好接地的金屬部位連接接地電	2
	纜。
3	按照放大器上的標記（1、2、3、4、TV）把天線輸入電纜連接	3	2 3	4 5 UW
	到電視天線放大器。
連接電視主機和汽車的 ACC 電源 (qs)			BDD	)qs*
1	把電視天線放大器 4 上的天線端子（L 型）連接到電視主	1	4	)M *
	機。	2		BDD
2		2		BDD
2	把附屬電源端子連接到到汽車的 ACC 電源。	•	BDD
	•從電視主機連接 ACC 電源線到備用觸點。	•
	•不要直接連接到電池。

更換前支柱壓條

)qd*

緊固電線，使其不成為障礙(qd)。

規格		QBM
		QBM
接收制式	PAL	DDJS
頻道	CCIR	3.23)WIG*
	2-12 (VHF)	32.7:)VIG*
	21-69 (UHF)
	中國	2.23)WIG*
	1-12 (VHF)	24.68)VIG*
	13-57 (UHF)	0
		0
	英國/香港	.)WIG*
	-(VHF)	32.7:)VIG*
	21-69 (UHF)
	紐西蘭	2.22)WIG*
	1-11 (VHF)	32.7:)VIG*
	21-69 (UHF)
	澳洲	1.23)WIG*
	0-12 (VHF)	39.7:)VIG*
	28-69 (UHF)	23WED
	（單聲道）	23WED
電源要求	12 V DC	351nB
	（負極接地）	351nB
消耗功率	240 mA	2
輸入	視頻（1）	2
	總線（1）	5
	電視天線（4）	2
輸出	視頻（1）	2
	總線（1）	238 41 218nn
外形尺寸	約 127×30×107 mm	1/49lh
	（寬×高×深）	1/49lh
質量	約 0.38 kg

設計與規格可能會變化，恕不另行通知。

Specifications

4 5 UW

BDD

)qs*

更換前支柱壓條

)qd*

QBM

PAL

DDJS

CCIR

3.23)WIG*

2-12 (VHF)

32.7:)VIG*

21-69 (UHF)

2.23)WIG*

1-12 (VHF)

24.68)VIG*

13-57 (UHF)

.)WIG*

-(VHF)

2.22)WIG*

1-11 (VHF)

1.23)WIG*

0-12 (VHF)

39.7:)VIG*

28-69 (UHF)

23WED

351nB

240 mA

238 41 218nn

約 127×30×107 mm

1/49lh

約 0.38 kg