Bluetooth™ Headsets | 2 |
|
|
Brugervejledning
User guide
Sony Ericsson HBH-PV715 and HBH-PV720
This User guide is published by Sony Ericsson Mobile Communications AB, without any warranty. Improvements and changes to this User guide necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Sony Ericsson Mobile Communications AB at any time and without notice. Such changes will, however, be incorporated into new editions of this User guide. All rights reserved.
©Sony Ericsson Mobile Communications AB, 2008
Publication number:
Some of the services in this User guide are not supported by all networks. This also applies to the GSM International Emergency Number 112. Contact your network operator or service provider if you are in doubt whether you can use a particular service.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Ericsson is under license. Sony and WALKMAN are trademarks or registered trademarks of Sony Corporation.
Ericsson is a trademark or registered trademark of Telefonaktiebolaget LM Ericsson.
This product is leadfree and halogenfree.
5
12
34
xxx xxx xx
1 | 2 | 3 |
xxx xxx xx
English
The Bluetooth™ headsets
a Sony Ericsson mobile phone.
Charging the headset
Before using the
Turning on and off the headset
To turn on the headset
•Press and hold down the on/off key until the indicator light shows a steady green light (if the light is red, the headset needs charging). After 3 seconds, the light turns off and the headset stays on.
To turn off the headset
•Press and hold down the on/off key until the indicator light shows a steady green light (if the light is red, the headset needs charging). After 2 seconds, the light fades and the headset turns off.
Pairing the headset
Before you can use the headset it has to be paired once with your phone. After a successful pairing, the headset connects automatically to the phone when it is turned on and within range.
To answer a call
•Press the call handling key briefly.
To reject a call
•Press and hold down the call handling key until you hear a short beep (after 2 seconds).
To redial the last number
•Double-click the call handling key.
To answer a second call
•Press the call handling key. The ongoing call is put on hold.
To switch between two calls
•Press and hold down the call handling key until you hear a beep.
To turn off the microphone (mute)
•Press both volume keys simultaneously. Mute is indicated with a beeping sound. Repeat to turn on the microphone again.
Adjusting volume
To adjust the ring volume
•When you are not making a call, or when the phone is ringing, press a volume key.
To adjust the speaker volume
•During a call, press a volume key.
Calling using voice commands
1 |
| 3 |
| 6 | |||||
|
| Microphone |
|
|
|
|
| ||
Volume keys | Indicator light |
|
|
|
| ||||
|
|
|
|
|
|
| |||
|
| On/off key |
|
|
|
| |||
Call handling |
| ||||||||
|
|
|
| ||||||
key | Earspeaker |
|
|
|
|
| |||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||
|
|
|
|
| |||||
Call handling key
Volume keys
4
1
2
3
Sony Ericsson Mobile Communications AB
Printed in XXXXX
Bemærk: When you put the headset in pairing mode, do not press the call handling key together with the on/off key.
To pair the headset with your phone
1.Turn on the Bluetooth function in the phone. For instructions, see the phone User guide.
2.Place the phone within 20 cm (8 inches) of the headset.
3.Turn on the headset. The first time you do so, the headset enters pairing mode automatically and tries to pair with your phone (auto pairing).
Bemærk: If auto pairing is not supported by your phone, or not successful, follow the two first steps above and turn on the headset. Then add the headset to your phone as described in your phone User guide. The passcode is 0000.
To pair the headset with another phone
1.Turn on the Bluetooth function in the phone. For instructions, see the phone User guide.
2.Place the phone within 20 cm (8 inches) of the headset.
3.Turn off the headset if it is turned on. Press and hold down the on/off key until the indicator light flashes red and green alternately.
4.Press Yes when Add device? appears in the phone. If required, the passcode is 0000. The headset beeps and flashes green when paired successfully.
Putting on the headset
Slide the ear hook behind your ear and point the microphone towards your mouth. For left ear use, change the position of the ear hook as instructed in figure 4.
Calling
When you have paired the headset with your phone, you can make and receive calls as long as the headset is turned on.
Solid objects, walls and a greater distance than 5 metres (16.5 feet) can affect the sound quality negatively. For best performance, you should wear the headset and the phone on the same side of your body.
To make a call
•Use the phone keys to dial the number as normal. The call is activated automatically in the headset.
To end a call
•Press the call handling key briefly.
Voice commands can be useful when you are using the headset and the phone is not close to you.
For more information on voice commands, see your phone User guide.
To make a call using voice commands
•Press the call handling key briefly, wait for a beep and say your command.
Bemærk: Make sure voice commands are enabled and recorded in your phone before you use them.
Transferring sound
To transfer sound from the phone to the headset
•During a call, press the call handling key briefly. The sound is transferred to the headset.
To transfer sound from the headset to the phone
•See the phone User guide.
Battery
A new, or infrequently used, battery could have reduced capacity. It may need to be recharged a few times to reach full capacity.
When the battery needs charging, the indicator light flashes red and you hear a low beep. If you do not charge the headset, it turns off automatically.
To check the battery status
•Press the on/off key briefly:
•steady green light plus one green flash – the battery needs charging soon
•steady green light plus two green flashes – the battery is half full
•steady green light plus three green flashes – the battery is fully charged
Resetting the headset
To reset the headset
1.Turn off the headset.
2.Press and hold down the on/off key until the indicator light flashes red and green alternately.
3.Press and hold down the on/off key and the call handling key simultaneously until the headset turns off.
4.Pair the headset with the phone in the same way as you paired it the first time.
This is the Internet version of the User guide. © Print only for private use.