HOSE TYPES

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are:

Certified non-conductive— constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non- conductive is the only hose authorized for use near electrical conductors.

Wire-braided(conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce- ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near electrical conductors.

Fabric-braided(not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in- ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This hose is not certified non-conductiveand must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

 

 

 

 

 

 

 

 

 

 

 

 

A G

 

D A N G E R

 

 

 

 

 

 

D A N G E R

 

T

 

 

 

 

 

 

 

 

 

 

I S

 

1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

3.

DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE

 

H

 

WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN

 

 

 

 

 

 

OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.

 

T

 

DEATH OR SERIOUS INJURY.

 

 

 

 

 

 

KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT

 

VE

 

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-

 

 

 

 

 

 

CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION

 

 

 

 

 

 

 

 

AND SEVERE PERSONAL INJURY.

 

O

 

ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND

 

 

 

 

 

 

 

 

 

ELECTRIC LINES.

 

 

 

 

 

4.

HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR

 

M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT

 

E

 

 

 

 

 

 

 

 

 

 

2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

 

USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

R

 

 

 

 

 

 

 

 

 

ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-

 

 

 

 

 

5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-

 

T

 

 

 

 

 

 

 

 

TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND

 

 

 

 

 

 

 

 

 

 

 

 

 

AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE

 

N O

 

TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

 

 

SAFETY DEPARTMENT INSTRUCTIONS.

 

 

 

 

 

6.

 

D O

 

 

 

 

 

 

 

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

 

SEE OTHER SIDE

 

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIDE 2

 

 

 

SIDE 1

 

 

 

 

 

 

(Shown smaller than actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D O N O T R E M O V E T H I S T A G

D O N O T R E M O V E T H I S T A G

 

D A N G E R

 

 

D A N G E R

 

 

 

 

 

1.

DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS

5.

CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO

 

NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR

 

COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.

 

ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

 

NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

2.

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY

6.

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-

 

 

 

TRIC LINES.

 

 

3.DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.

4.HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

 

SEE OTHER SIDE

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

SIDE 1

 

 

SIDE 2

(Shown smaller than actual size)

D O N O T R E M O V E T H I S T A G

DL07 User Manual ◄ 7

Page 6 Page 8
Page 7
Image 7
Stanley Black & Decker DL07 user manual Hose Types, Hose Safety Tags, TAG Shown below is Attached to Conductive Hose
Page 6 Page 8

DL07 specifications

Stanley Black & Decker DL07 is a powerful and versatile cordless impact wrench designed for both professionals and DIY enthusiasts. Renowned for its robust performance and innovative features, the DL07 is ideal for a wide range of applications, including automotive repair, construction, and heavy-duty fastening tasks.

One of the standout features of the DL07 is its brushless motor technology, which offers superior efficiency and increased runtime compared to traditional brushed motors. The brushless design not only enhances the tool's longevity but also ensures consistent power delivery, allowing users to tackle tough jobs with ease. The motor generates impressive torque, providing the necessary strength to loosen stubborn bolts and drive fasteners quickly.

The 20V battery platform is another hallmark of the DL07, offering a powerful power source with extended battery life. Users can easily swap batteries with other tools in the Stanley Black & Decker lineup, making it a convenient addition to any toolkit. The tool’s ergonomic design, complemented by an adjustable soft grip, ensures comfort during prolonged use, reducing user fatigue.

The DL07 also features a built-in LED work light, illuminating dark working areas and enhancing visibility while working in confined spaces. This is particularly useful for automotive work and other applications where lighting is subpar. Additionally, the variable speed trigger provides precise control over the wrench's speed, allowing users to adjust the power output based on the specific task at hand.

With its 1/2-inch anvil and friction ring, the DL07 ensures quick and secure socket changes, making it easy to switch attachments as needed. The compact and lightweight design enhances portability, making it an ideal option for users who often work in tight or elevated spaces.

Durability is key, and the DL07 excels in this area as well, featuring a rugged housing designed to withstand the rigors of daily use. Whether you're a seasoned professional or a home improvement novice, the Stanley Black & Decker DL07 impact wrench delivers the performance, reliability, and innovative features needed to get the job done efficiently. With its combination of power, versatility, and user-friendly design, it stands out as a top choice in the cordless impact wrench market.
Top Page Image Contents