HOSE TYPES

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are:

Certified non-conductive— constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non- conductive is the only hose authorized for use near electrical conductors.

Wire-braided(conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce- ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near electrical conductors.

Fabric-braided(not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in- ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This hose is not certified non-conductiveand must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

 

 

 

 

 

 

 

 

 

 

 

 

A G

 

D A N G E R

 

 

 

 

 

 

D A N G E R

 

T

 

 

 

 

 

 

 

 

 

 

I S

 

1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

3.

DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE

 

H

 

WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN

 

 

 

 

 

 

OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.

 

T

 

DEATH OR SERIOUS INJURY.

 

 

 

 

 

 

KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT

 

VE

 

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-

 

 

 

 

 

 

CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION

 

 

 

 

 

 

 

 

AND SEVERE PERSONAL INJURY.

 

O

 

ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND

 

 

 

 

 

 

 

 

 

ELECTRIC LINES.

 

 

 

 

 

4.

HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR

 

M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT

 

E

 

 

 

 

 

 

 

 

 

 

2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

 

USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

R

 

 

 

 

 

 

 

 

 

ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-

 

 

 

 

 

5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-

 

T

 

 

 

 

 

 

 

 

TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND

 

 

 

 

 

 

 

 

 

 

 

 

 

AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE

 

N O

 

TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

 

 

SAFETY DEPARTMENT INSTRUCTIONS.

 

 

 

 

 

6.

 

D O

 

 

 

 

 

 

 

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

 

SEE OTHER SIDE

 

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIDE 2

 

 

 

SIDE 1

 

 

 

 

 

 

(Shown smaller than actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D O N O T R E M O V E T H I S T A G

D O N O T R E M O V E T H I S T A G

 

D A N G E R

 

 

D A N G E R

 

 

 

 

 

1.

DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS

5.

CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO

 

NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR

 

COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.

 

ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

 

NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

2.

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY

6.

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-

 

 

 

TRIC LINES.

 

 

3.DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.

4.HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

 

SEE OTHER SIDE

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

SIDE 1

 

 

 

 

 

SIDE 2

 

 

 

(Shown smaller than actual size)

D O N O T R E M O V E T H I S T A G

RD12 User Manual ◄ 7

Page 6 Page 8
Page 7
Image 7
Stanley Black & Decker RD12 user manual Hose Types, Hose Safety Tags
Page 6 Page 8

RD12 specifications

Stanley Black & Decker has long been recognized for its commitment to quality and innovation in the tool and hardware industries. One notable product that embodies this dedication is the Stanley Black & Decker RD12, a reciprocating saw that stands out for its performance, versatility, and user-friendly design.

The RD12 features a powerful motor that delivers high-speed cutting action, making it ideal for a variety of applications, from demolition to woodworking. With its cutting stroke length and speed, users can tackle tougher materials with ease, ensuring efficient performance on the job. The saw is designed to handle both wood and metal, showcasing its adaptability across different projects and materials.

One of the standout features of the RD12 is its lightweight and ergonomic design. Weighing in at just a few pounds, it minimizes user fatigue during extended use, allowing professionals and DIY enthusiasts alike to work comfortably. The soft-grip handle enhances control and precision, reducing the risk of slips or mishaps.

Technologically, the RD12 is equipped with a tool-less blade change system, which significantly increases convenience. Users can quickly swap out blades without the need for additional tools, saving valuable time and maintaining workflow. This feature is particularly useful in fast-paced work environments where efficiency is essential.

The RD12's built-in variable speed trigger allows users to control the cutting speed, giving them the flexibility to adjust their approach depending on the material and application. This level of control contributes to more precise cuts and enhances overall performance.

Durability is another hallmark of the RD12. Constructed from robust materials, this saw is built to endure demanding job site conditions. The inclusion of protective features, such as a heavy-duty housing and advanced cooling mechanisms, helps prevent overheating, keeping the motor in optimal working condition.

For safety, the RD12 incorporates a lock-off switch, which prevents accidental starts and provides peace of mind during operation. This is an essential feature for both professional tradespeople and home users, ensuring safe handling at all times.

In conclusion, the Stanley Black & Decker RD12 is an impressive reciprocating saw that combines power, versatility, and user-friendly features. With its innovative technologies, such as the tool-less blade change and variable speed settings, along with its ergonomic design, the RD12 represents a reliable choice for anyone looking to invest in a high-quality cutting tool. Whether you're a seasoned professional or an enthusiastic DIYer, the RD12 stands ready to tackle a multitude of cutting tasks with precision and ease.
Top Page Image Contents