|
|
| APPENDIX | |||
Connectors and Signals (Serial Interface) |
|
| ||||
|
|
|
|
|
| |
Pin no. |
| Signal name |
| I/O |
| Function |
|
| direction |
| |||
|
|
|
|
|
| |
|
|
|
|
|
|
|
1 |
|
| — |
| Frame ground | |
|
|
|
|
|
|
|
2 |
| TXD |
| OUT |
| Transmitted data |
|
|
|
|
|
|
|
3 |
| RXD |
| IN |
| Received data |
|
|
|
|
|
|
|
4 |
| RTS |
| OUT |
| Data transmission request signal. This |
|
|
|
|
|
| is always “SPACE” when the printer is |
|
|
|
|
|
| turned on. |
|
|
|
|
|
|
|
5 |
| CTS |
| IN |
| This signal changes to “SPACE” when |
|
|
|
|
|
| host computer is ready to transmit data. |
|
|
|
|
|
| (In this instance, the printer does not |
|
|
|
|
|
| check this signal.) |
|
|
|
|
|
|
|
6 |
| N/C |
|
|
| Not connected |
|
|
|
|
|
|
|
7 |
|
| — |
| Signal ground | |
|
|
|
|
|
|
|
8 |
| N/C |
|
|
| Not connected |
|
|
|
|
|
|
|
| N/C |
|
|
| This pin is used when using the op- | |
|
|
|
|
|
| tional interface board. |
|
|
|
|
|
|
|
11 |
| RCH |
| OUT |
| This signal changes to “SPACE” when |
|
|
|
|
|
| the printer is ready to receive data. (The |
|
|
|
|
|
| signal line is same as pin 20.) |
|
|
|
|
|
|
|
12 |
| N/C |
|
|
| Not connected. |
|
|
|
|
|
|
|
13 |
|
| — |
| Signal ground | |
|
|
|
|
|
|
|
14 |
| FAULT |
| OUT |
| When a printer error occurs (such as |
|
|
|
|
|
| paper out, mechanical error, etc.), this |
|
|
|
|
|
| signal is set to “MARK”. |
|
|
|
|
|
|
|
15 |
|
| OUT |
| Diode coupled TXD | |
|
|
|
|
|
|
|
16 |
|
| OUT |
| Diode coupled DTR | |
|
|
|
|
|
|
|
17 to 19 |
| N/C |
|
|
| This pin is used when using the op- |
|
|
|
|
|
| tional interface board. |
|
|
|
|
|
|
|
20 |
| DTR |
| OUT |
| Data terminal ready signal. When the |
|
|
|
|
|
| printer is ready to receive data, this |
|
|
|
|
|
| signal changes to “SPACE”. |
|
|
|
|
|
|
|
| N/C |
|
|
| Not connected | |
|
|
|
|
|
|
|
23 to 25 |
| N/C |
|
|
| This pin is used when using the op- |
|
|
|
|
|
| tional interface board. |
|
|
|
|
|
|
|
APPENDIX
Serial interface connector
– 49 –
