Manuals / Sterling / Household Appliance / Dehumidifier

Sterling 882.00291.00 Installation, 3-1Uncrating the Equipment, 3-2Rigging and Placing the Dryer

Models: 882.00291.00

1 50

Download 50 pages 20.38 Kb

Page 14

Chapter 3: Installation

Chapter 3: Installation

3-1 Uncrating the Equipment

Dehumidifying Dryers are shipped mounted on a skid, enclosed in a plastic wrapper, and contained in a cardboard box.

1. Pry the crating away from the skid.

Note: Remove the nails holding the box to the skid and lift the box off carefully; avoiding staples in the 1’ x 4’ wood supports. Cut the steel banding.

2.Use a pry bar to remove the blocks securing the unit to the skid.

3.Lift unit from sides. Use a pry bar if necessary to carefully remove the skid from the unit.

4.Lower slowly.

3-2 Rigging and Placing the Dryer

Take care when rigging and placing the dryer. Figures 1, 2 and 3 on the following pages show a suggested safe rigging diagram. It lets you lift the dryer/hopper unit vertically for installation on the machine throat. Adjust chain lengths at the center sling bracket before you lift the unit. Your dryer has built-in lifting lugs.

Caution! If you are mounting a machine-mount dryer with a magnet or transition adaptor on the machine throat, you must provide additional support to hold the dryer securely on the machine.

Be aware that off-center static and dynamic hopper loading can occur with machine vibration. Again, provide additional support to hold the dryer securely on the machine.

Use caution and observe safety rules when lifting and placing your dryer!

15, 30, & 60 cfm Compact Dryers

14

Image 14

Sterling 882.00291.00 specifications Installation, 3-1Uncrating the Equipment, 3-2Rigging and Placing the Dryer

Contents

15, 30, & 60 cfm Compact Dehumidifying Dryers In the Event of Shipping Damage Shipping InformationUnpacking and Inspection If the Shipment is Not CompleteCHAPTER 3 INSTALLATION Table of ContentsCHAPTER 1: SAFETY CHAPTER 2 FUNCTIONAL DESCRIPTIONCHAPTER 7: APPENDIX CHAPTER 5: MAINTENANCECHAPTER 6: TROUBLESHOOTING 15, 30, & 60 cfm Compact DryersSafety Symbols Used in this Manual Chapter 1 Safety1-1How to Use This Manual Read Operation and Installation Manual 1-2Safety Tag Information1-3Warnings and Precautions Dryer Safety TagsOperator Responsibility 1-4ResponsibilityGeneral Responsibility REMEMBER Maintenance Responsibility Reporting a Safety Defect2-2General Description Chapter 2 Functional Description2-1Models Covered in This Manual What is desiccant?Mechanical Features 2-3Standard FeaturesFigure 1: Typical Dryer Air Flow Schematic Electrical FeaturesController Features 2-5Safety Devices and Interlocks2-4Options Fail Safe Operation Safety Circuit StandardsSafety Device Lock-Outs 3-2Rigging and Placing the Dryer Chapter 3 Installation3-1Uncrating the Equipment DEW POINT POWER ON15, 30, & 60 cfm Compact Dryers 3-3Electrical Connections Checking for Proper Blower Rotation 3-4Setup ProceduresThree-PhaseModels Floor Mount ModelsDrying Hopper Air Trap Considerations 3-5Initial Start-upInstalling Water Lines Optional AftercoolerAuto-Tuningthe Dryer Shutting Down the DryerSwitches Chapter 4 Operation4-1Controller Description and Operation Indicator LightsProcess Air Temperature Controller PV SVLit when Control Output 2 is on. Not used in IndicatorLit when Control Output 1 is on. The Out1 IndicatorAdjustment Level Setting the Process Air TemperatureIndicator IndicatorDescription IndicatorName Entering Operating Parameters to Select ModesOptional Setting the High Dew Point AlarmProcess Air Dew Point Display 4-2Dryer Operation Procedures Controller OperationAlarm Display Messages Valve Motor Time-Out Blower Overload No Alarms HIGH TEMP VALVE MTRHEAT COOL 50 SYSTEM NORMAL PROC BLWREvery Day Chapter 5 Maintenance5-1Preventative Maintenance Schedule Every weekServicing Process Air Filters 5-2Preventative MaintenanceFigure 9 Air Filter Location and Disassembly VacuumingSymptoms of Worn Desiccant 5-3Corrective MaintenanceCleaning with Compressed Air Servicing the Dew Point Monitor+ FIRST AID + Replacing Worn DesiccantFigure 10 Desiccant Bed Location and Disassembly Figure 11 Required Desiccant Amounts 13X TypeWARNING! Hazardous electrical current present ProceduresReplacing the Process/Regeneration Heater Replacement Procedures Replacing/Cleaning the Cooling CoilFigure 13 Cooling Coil Location and Disassembly If used as an after-Cooler 3 to 4 GPM @ 85F15, 30, & 60 cfm Compact Dryers 8.Inset the four 10-32bolts back in place9.Turn the water to the cooling coil back on HIGH TEMP Chapter 6 Troubleshooting6-1Introduction HIGH TEMP PROC BLWRAlarm Message CauseAlarm Message VALVE MTRUsing a Thermocouple CauseAnnex B Information 7-1Technical SpecificationsChapter 7 Appendix Regeneration MoistureMake Up Air Exhaust 7-2Drawings and DiagramsAftercooler Design Specifications High Pressure Peripheral BlowerExhaust Figure 16 Low Heat Model 120F to 250F Air FlowAfter-Cooler Regeneration MoistureMake Up Air High Pressure Peripheral Blower15, 30, & 60 cfm Compact Dryers 7-3Spare Parts ListDRYER SPARE PARTS LIST 15, 30, 60 cfm Models Mechanical Components15, 30, & 60 cfm Compact Dryers HI-COREDESICCANT DRYER 15/30/60 CFM UNITSDescription 15, 30, & 60 cfm Compact Dryers30 CFM Description 15, 30, & 60 cfm Compact Dryers60 CFM 120V CONTROL COMMON PARTS 15, 30, & 60 cfm Compact DryersA0571672 Description15, 30, & 60 cfm Compact Dryers Warranty Returns 7-5Returned Material Policy7-6Dryer Identification Serial Number Tag Credit ReturnsParts Department 7-7Technical AssistanceService Department Sales Department