Sterling 882.00294.00, DH1-610-2 2-3 Standard Features

2-3 Standard Features

Mechanical Features

• Rugged compact cart with handles and sturdy 4” (10 cm) casters.

• Dual desiccant beds

• Electrically-motorized air valve

• 13X Molecular Sieve

• Single regenerative process blower

• Drying temperature range of 180ºF to 250ºF (82ºC to 121ºC)

• 2.5” hose connections

Electrical Features

• Process thermocouple to be connected to drying hopper air inlet.

• Nema 12 control enclosure

• NFPA79 machinery electrical standards

• Non-fused electrical disconnect

• Branch fusing

• Solid State process heater contactor

• Regeneration temperature control

• Process high temperature alarm light

• Dirty filter indicator

• Process/regeneration heater box

• Dew Point Monitor.

• Material saver/over dry protection

• High temperature safety system (Process/Regeneration)

• 7 day timer/auto start

Controller Features

• Mitsubishi programmable relay controller

• Display of process temperature set point and actual settings

• Display of process air dew point

Portable Drying/Conveying Systems Chapter 2: Functional Description 12 of 63

Contents

Main SDAA 25-100 Small Dryer With AP-1 Controls Shipping Information Table of Contents CHAPTER 1: SAFETY ................................................................6 CHAPTER 2: FUNCTIONAL DESCRIPTION............................ 11 CHAPTER 3: INSTALLATION ..................................................15 CHAPTER 4: OPERATION .......................................................21 CHAPTER 5: MAINTENANCE.................................................. 40 CHAPTER 6: TROUBLESHOOTING........................................ 48 CHAPTER 7: APPENDIX ..........................................................55 Chapter 1: Safety 1-1 How to Use This Manual DANGER! 1-2 Safety Tag Information 1-3 Warnings and Precautions 1-4 Responsibility Page Page Chapter 2: Functional Description 2-1 Models Covered in This Manual 2-2 General Description 2-3 Standard Features 2-4 Options 2-5 Safety Devices and Interlocks Page Chapter 3: Installation 3-1 Uncrating the Equipment 3-2 Rigging and Placing the Dryer Note: Floor Mounted Dryers can be lifted by hoist or fork lift. USE FORK LIFT TRUCK USE Overhead Crane 3-3 Electrical Connections 3-4 Setup Procedures Checking for Proper Blower Rotation Drying Hopper Air Trap Considerations (If Equipped) Installing the Optional Aftercooler 3-5 Initial Start-up Pre-Startup Checks Starting Up the Dryer The process blower starts. Auto-Tuning the Dryer (Requires Supervisory Password) Page Chapter 4: Operation 4-1 Controller Description and Operation Page Page Page Page Page Page Page Page Page Page Page Page Page Page Restoring the WATLOW Redundant Safety Controller to Factory Setup Entering Operating Parameters to Select Modes Figure 6: Setting List for Redundant Safety Controller (WATLOW), Part No. A0568961 4-2 System Operation Procedures process. regeneration. beginning. 4-3 Shutting Down the Dryer Chapter 5: Maintenance 5-1 Preventative Maintenance Schedule Portable Drying/Conveying Systems Chapter 5: Maintenance 40 of 63 replacement date inspection 5-2 Preventative Maintenance Servicing Process Air Filters Recommendations for Cleaning and Replacing Filters Figure7: Air Filter Location and Disassembly Vacuuming Cleaning with Compressed Air Servicing the Dew Point Monitor 5-3 Corrective Maintenance Symptoms of Worn Desiccant + FIRST AID + In case of eye contact, immediately flush eyes with plenty of water for at least 15 minutes. SEE A PHYSICIAN IMMEDIATELY IF IRRITATION PERSISTS. Replacing Worn Desiccant Figure 8: Desiccant Bed Location and Disassembly Figure 9: Required Desiccant Amounts Replacing the regeneration heaters Procedures (see figure 8). Replacing the Process Heater Figure 10: Process Heater Location and Disassembly Procedures Replacing/Cleaning the Cooling Coils Figure 11: Cooling Coil Location and Disassembly Page Chapter 6: Troubleshooting 6-1 Introduction Page Page Page Page Page 6-2 Determining Temperature Controller Errors or Sensor Errors Using a Thermocouple Chapter 7: Appendix 7-1 Warranty Warranty Specifications Warranty Restrictions Warranty Liabilities 7-2 Optional Components 7-3 Technical Specifications Annex B Information Aftercooler Design Specifications Portable Drying/Conveying Systems Chapter 7: Appendix 57 of 63 7-4 Drawings and Diagrams Figure 12: Standard Model (180F to 250F) Air Flow Schematic Page Figure 14: Low Heat Model (120F to 250F) Air Flow Schematic 7-5 Spare Parts List Figure 15: Level 1 Spare Parts List (Electrical & Mechanical) Portable Drying/Conveying Systems Chapter 7: Appendix 60 of 63 Page 7-6 Returned Material Policy 7-7 Dryer Identification (Serial Number) Tag 7-8 Technical Assistance Portable Drying/Conveying Systems Chapter 7: Appendix 63 of 63 Parts Department Service Department Sales Department