Sun Lawn BDP-HD1 Connecting using the component video output, Changing the video output format

Connecting up02

Connecting using the component

video output

You can use the component video output instead of the standard

video out jack to connect this player to your TV (or other equipment).

•Use a component video cable (not supplied) to connect the

COMPONENT VIDEO OUT jacks to a component video input on

your TV, monitor or AV receiver.

Be careful to match up the colors of the three jacks for correct

connection.

Changing the video output format

Use the OUTPUT FORMAT button located on both the front panel

and the remote control to switch the video output format for the

component and HDMI video outputs.

The table below shows the output settings.

*1 Video output is 480i during copy protected DVD-Video playback.

*2 Video output during BD-ROM playback is 480i depending on the disc.

*3 Refer to 24p output below for conditions.

*4 The frame frequency for 1080/24p is still 60 Hz.

*5 The video output will be interrupted when switching the video output.

Note

• Depending on your display, some of the settings may result in

the picture disappearing. In this case, press OUTPUT FORMAT

repeatedly until the picture re-appears.

• 1080/60p and 1080/24p output is only compatible with HDMI

displays. They are not compatible with the component video

output.

• When Output Format is set to 720p, 1080i or 1080p, video is

output in 16:9 format even if TV Aspect Ratio is set to 4:3

(Standard). See TV Aspect Ratio on page 41.

•If the contours of the displayed subjects look jagged or blurred,

try setting the Output Format to 480i. (If you connected this

player to your TV with the HDMI connection and the picture

disappears when you switch the Output Format to 480i, use the

component connection with the 480i Output Format or S-Video,

the standard composite connection instead.)

•Note that when using a Component Video connection with a TV

or other AV component (not using HDMI), 480/60i video may be

output in 480/60p.

24p output

For smooth presentation of 1080/24p or 720/24p video with an

HDMI-equipped display compatible with 1080/24p input, set 24p

Direct Out on this player to On (see page 41).

This player will output 1080/24p video over HDMI in the following

cases:

• 1080/24p video: When Output Format is set to Auto or Source

Direct.

• 720/24p video: When Output Format is set to Auto.

Note

• Even when 24p Direct Out is set to On, if a TV not compatible

with 1080/24p video is connected, the actual frame frequency

of the video output will be 60 Hz.

• The video output will be interrupted when switching the video

output from 1080/24p or 720/24p to other output resolutions, or

when switching to 1080/24p or 720/24p from other output

resolutions.

Setting HDMI output Component

output

Video/S-Video

output

AUTO TV’s preferred

format *3,5

480/60i 480/60i

480i 480/60i 480/60i 480/60i

480p 480/60p 480/60p 480/60i

720p 720/60p 720/60p *1,2 480/60i

1080i 1080/60i 1080/60i *1,2 480/60i

1080p 1080/60p 480/60i 480/60i

Source

Direct

Dependent on

source *3,5

Dependent on

source *2,4,5

480/60i

AUDIO OUT

(5.1ch)

DIGITAL AUDIO OUT

AUDIO OUT

(2ch)

CENTER

SUB WOOFER

FRONT

SURROUND

COAXIAL OPTICAL

COMPONENT

VIDEO OUT

LAN(10/100)

HDMI OUT

SETTING 2

SETTING 1

IR RECEIVER

CONTROL

COMPONENT

VIDEO IN