Superior 500, 600, 800 Figure 4, Figure 5, Figure 6, Figure 7

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

hctiPfooR)teef(H

21/6ottalF0.1

21/7ot21/6revO52.1

21/8ot21/7revO5.1

21/9ot21/8revO0.2

21/01ot21/9revO5.2

21/11ot21/01revO52.3

ot21/11revO 21/21 0.4

Right Side

Front Corner of

Fireplace Framing

6 ¹⁄₂"

(152 mm)

(76 mm)

12"

(305 mm)

Termination Kit

Combustible Projection

greater than 2¹⁄₂ inches in length

Horizontal Vent Termination Clearances

Combustible Projection

2¹⁄₂ inches or less in length

18"

(457 mm)

Ventilated

Soffit Unventilated

Soffit

Roof Pitch is X/12

2 FT

MIN.

2 FT MIN.

Lowest

Discharge

Opening

*H = MINIMUM HEIGHT FROM ROOF TO

LOWEST DISCHARGE OPENING OF VENT

TERMINATION HEIGHTS FOR VENTS ABOVE

FLAT OR SLOPED ROOFS

Horizontal Overhang

Vertical

Wall

Vent

Termination

Storm Collar

Concentric

Vent Pipe

Flashing

1 inch (25.4 mm) Minimum

Clearance to Combustibles

Figure 4Figure 5Figure 7Figure 6

Note: The nailing flanges, combustible members

and screw heads located in areas directly adjacent

to the nailing flanges, are EXEMPT from the 1/2”

clearance to combustible requirements for the

firebox outer wrapper. Combustible framing may be

in direct contact with the nailing flanges and may

be located closer than 1/2” from screw heads and

the firebox wrapper in areas adjacent to the nailing

flanges. Frame the opening to the exact dimensions

specified in the framing details of this manual.

Side

Framing

Unit Nailing Flange

(No clearance to

combustible

framing is required)

Left Side Front Corner of Fireplace Shown

(Right Side Requirements the Same)

Unit Being Secured By Its Nailing Flanges

To The Framing

Horizontal Vent Termination Clearances

The horizontal vent termination must have a

minimum of 3" (76 mm) clearance to any

overhead combustible projection of 2 ¹⁄₂" (64

mm) or less. See

Figure 5.

For projections

exceeding 2 ¹⁄₂" (64 mm), see

Figure 5

. For

additional vent location restrictions refer to

Figure 8 on page 6

Terminate multiple vent terminations accord-

ing to the installation codes listed at the top of

this page.

Vertical Vent Termination Clearances

VENT TERMINATION CLEARANCES

These instructions should be used as a guide-

line and do not supersede local codes in any

way. Install vent according to local codes,

these instructions, the current National Fuel

Gas Code (ANSI-Z223.1) in the USA or the

current standards of CAN/CGA-B149.1 and -

B149.2 in Canada.

Terminate single vent caps relative to building

components according to

figure 4

Step 3. (page 9) Install the vent system and

exterior termination.

Step 4. (page 21) Field Wiring

a. Millivolt Appliances – Install the operating

control switch (not factory provided) and bring

in electrical service line for forced air circulating

blower (optional equipment).

b. Electronic Appliances – Field wire and install

operating control switch.

Step 5. (page 21) Install blower kit (optional

equipment).

Step 6. (page 22) Make connection to gas supply.

Step 7. (page 22) Install the logs, decorative

volcanic stone and glowing embers.

Step 8. (page 22) Checkout appliance operation.

Step 9. (page 23) Install glass door frame assembly.

Step 10. (page 23)Adjust burner to ensure

proper flame appearance.

Step 11. (page 23) Install the hoods.

See

Figure 10 on page 7 or Figure 11 on page

8

for corner framing installations. All framing

details must allow for a minimum clearance to

combustible framing members as shown in

Table 2

Step 2. ROUTING GAS LINE

Route a ¹⁄₂" (13 mm) gas line along the inside of

the right side framing as shown in

Figure 7

Gas lines must be routed, constructed and

made of materials that are in strict accordance

with local codes and regulations.

All appliances are factory-equipped with a flex-

ible gas line connector and ¹⁄₂ inch shutoff

valve. (See step 6 on page 22).

Note - See

Figure 34 on page 16

for the recess allow-

ances, into exterior walls, of the round, square and

small square horizontal terminations.

Side Elevation View

TYPICAL INSTALLATION SEQUENCE

The typical sequence of installation follows,

however, each installation is unique resulting in

variations to those described.

See the page numbers references in the follow-

ing steps for detailed procedures.

Step 1. (page 5) Construct the appliance fram-

ing. Position the appliance within the framing

and secure with nailing brackets.

Step 2. (page 5) Route gas supply line to

appliance location.

DETAILED INSTALLATION STEPS

The appliance is shipped with all gas controls

and components installed and pre-wired. Re-

move the shipping carton, exposing the front

glass door. Remove the top panel. Remove the

cardboard from underneath the pressure re-

lief plates. Gently depress the outer top cor-

ners of the access panel until the catches "pop"

the panel free, allowing it to swing out and down

to open. Open the two latches (located under

the firebox floor) securing the glass door. Re-

move the door by tilting it outward at the

bottom and lifting it up. Set the door aside

protecting it from inadvertent damage.

See

Figure 55 on page 23.

Step 1. FRAMING

Frame these appliances as illustrated in

Figure 9 on page 7,

unless the appliance is

to be installed in a corner

.

The fireplace should be secured to the side

framing members using the unit's nailing flanges

- one top and bottom on each side of the

fireplace front. See

Figure 6.

Use 8d nails or

their equivalent.

If the appliance is to be elevated above floor level,

a solid continuous platform must be constructed.

Headers may be in direct contact with the appli-

ance top spacers but must not be supported by

them or notched to fit around them. All construc-

tion above the appliance must be self supporting.

DO NOT use the appliance for structural support.