– 3–EN
1Disconnect the AC power cord of the TV from the AC
outlet.
2Disconnect the antenna or cable from the TV.
3Connect the antenna or cable to the ANT.IN jack of
the VCR.
4Connect the VCR to the TV using the RF cable.
5Plug the AC power cords of the VCR and TV into the
AC outlets.
ANT
IN
OUT
[VHF/UHF
combination antenna] [Back of the VCR]
IN OUT
[Cable box or satellite box]
OR
[Indoor antenna] [Back of the
UHF/VHF combination TV]
UHF/VHF
RF cable
(supplied)
From Cable or
Satellite Company
OR
If your TV does not have A/V terminals:
Press [PLAY] on the VCR for 3 seconds during playback.The RF
output channel will change to CH4 from CH3.
When you want to return to CH3 for RF output channel, press
[PLAY] on the VCR for 3 seconds during playback again.(Default
setting :CH3)
• There is case that the RF output channel does not change by sit-
uation (For example, when you adjust tracking using
[CHANNEL ].
In this case, stop the playback, and start the playback again.
After that, press [PLAY] on the VCR for 3 seconds.
• If there is a power failure or the VCR is unplugged for more
than 30 seconds, the RF output channelsetting will return to
CH3.
( )
You can automatically program the tuner to scan only the chan-
nels you receive in your area.
•Channel memory programming is NOT needed when you con-
nect the VCR to a cable box or satellite box as in "Connect VCR
to TV Connection".In this case, select the VCR and TV to chan-
nel 3, the same channel as the RF output channel of the VCR.
Then, the channel you want to record or view may be selected
at the cable box or satellite box.
•Follow the steps below once.Repeat it only if there is a power
failure or if the VCR is unplugged for more than 30 seconds.(In
these cases, the programmed channels are erased.)
•You must follow the steps below before attempting to play or
record a video tape.If you want to play or record a video tape
BEFORE programming the tuner, you can cancel it by pressing
[C.RESET/EXIT].
1You need to connect the antenna or cable to the VCR
first.Then, connect the VCR power plug into a stan-
dard AC outlet.
2Turn on the TV and set the TV to channel 3.If channel 3
is already occupied for broadcasting, change theR F output
to CH 4, and change the TV channel to CH4.
(See “RF Output Channel”on page 3 for the detail.)
3Turn on the VCRby pressing [POWER]. When the
POWER is on, both the POWERand VCR/TV indicator on
the VCR will be on.
4Select the On Screen Language
("ENGLISH" ,"FRANCAIS" or
"ESPAÑOL") by pressing [PLAY] or
[STOP].Then, press [F.FWD].
5Begin channel preset by pressing [F.FWD] once.The
tuner scans and memorizes all active
channels in your area.
• The VCR distinguishes between standard
TV channels and cable channels.
6After scanning,the tuner stops on the lowest memo-
rized channel.The TV screen returns to TV mode.
• If "AUTO SET UP" appears on the TV screen again, check
the cable connections.Press [F.FWD] once again and the
VCR will begin preset again.
Using Optional AUDIO/ VIDEO Output Jacks
With this connection, you can get better pictures and sounds
when playing back a tape if your TV has A/V Input jacks.Please
refer to your TV’s owner’s manual.
Using AUDIO/VIDEO Input Jacks
You can use the A/V input jacks on the front or the back of
the VCR.
• To use the input jacks on the back of the VCR, select "L1" posi-
tion by pressing [0], [0], [1] on the remote control or
[CHANNEL ].
• To use the input jacks on the front of the VCR, select "L2" posi-
tion by pressing [0], [0], [2] on the remote control or
[CHANNEL ].
• “L1”or “L2”is found before the lowest memorized channel.
(Example:CH2)
( )
( )
[TV A/V]
IN
AUDIO
LR
VIDEO
VIDEO
OUT IN
AUDIO
[Playing VCR]
Audio/Video cables
(not supplied)
VCR to TV Connection
RF Output Channel
VCR to AV TV connection using AUDIO/VIDEO Cables
SETUP
Automatic Channel Set Up
PREPARATION FOR USE
You can select the desired channel by using [CHANNEL ]
or directly pressing [Number] on the remote control.
Note for using the Number buttons:
• When selecting cable channels which are higher than 99,
enter channel numbers as a three-digit number.(For example:
117, press 1,1,7)
• You must precede single-digit channel numbers with a zero
(For example:02, 03, 04 and so on).
1Press [MENU] until the main menu appears.
2Select "CHANNEL SET UP" by pressing [PLAY] or
[STOP].Then, press [F.FWD].
3Select "AUTO SET UP"by pressing [PLAY] or [STOP].
Then, press [F.FWD].After scanning, the tuner stops on
the lowest memorized channel.
To Preset the Channel Again
( )
To Select a Desired Channel
ENGLISH
LANGUAGE SELECT
FRANCAIS
AUTO SET UP
CH 01
HD310.QX33 02.11.8 14:31 Page 3