PREPARATION FOR USE
CONNECTIONS
You can enter into Video mode from Game mode by adjusting a Picture control.
Plug the incoming cable into the ANT. IN jack on the rear of the TV.
1To use external input
2To cancel Game mode only
Cable OR Antenna
TV signal
Incoming cable from home Antenna /
Cable Company (No Cable Box)
Cable Box or
Satellite Box*
OR
OUT
IN 
Rear of this TV
ANT. IN
GAME
GAME
Picture: GAME (ON)
Input: External
MENU
| VOL |
| GAME MODE [+] | ||
|
| OFF |
| ON | |
|
|
|
| ||
|
|
|
|
|
|
Select “PICTURE” |
|
|
| ||
|
|
| |||
|
|
|
|
|
|
After 10 seconds |
|
| VIDEO | ||
|
|
|
|
| |
|
|
|
|
|
|
Picture: Customized
Incoming cable from Cable | *Note (DO NOT DISCONNECT FROM BOX) | |
Company or Satellite Antenna | Some cable TV systems use scrambled signals and | |
Cables not included | require a special converter to receive these channels. | |
Consult your local cable company. | ||
|
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
Note:
• For your safety and to avoid damages to the unit, unplug the antenna cable from the |
Input: External
3To return to TV channel
15
GAME
2 times
OPERATIONS
REMOTE CONTROL AND FRONT PANEL FUNCTION
ANT. IN jack before moving the unit. |
[EXTERNAL CONNECTION]
IR transmitter
To send infrared ray (IR) signal
POWER button
GAME button
Press to set the Game mode
Front AUDIO/VIDEO input
Front of this TV
VIDEO AUDIO
To turn TV on/off
POWER | GAME SLEEP |
SLEEP button
ex.
Channel number buttons
1 2 3
DISPLAY
To set Sleep Timer
Video Cable
(OUT)(IN)
Press two digits to directly access the desired channel. Remember to press
4 5 6
7 8 9
CHANNEL
RETURN
DISPLAY button
To display CH No./Audio Status
Video Camera | Video Game | (OUT) | (IN) |
Audio Cable |
|
INSTALLING THE BATTERIES |
| ||
1 | 2 | 3 | Install two AA batteries (supplied) |
|
|
| matching the polarity indicated inside |
|
|
| battery compartment of the remote con- |
|
|
| trol. |
a "0" before a single digit channel.
CH(ANNEL) K / L buttons
To select channels and move up/down through menu items
MENU button To view
0 +100
| CH |
VOL | VOL |
| CH |
| MUTE |
MENU
CHANNEL RETURN button
To return previous screen
MUTE button
To mute sound
VOL(UME) K / L buttons To adjust volume
To decide the command of settings
[BATTERY PRECAUTIONS]
•Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
•Do not mix different types of batteries together (e.g. Alkaline and
•If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
•Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
INITIAL SETUP
When you turn on the power for the first time, the "SELECT LANGUAGE" menu is displayed. The “INITIAL SETUP” menu is displayed every time you turn on the unit unless the scanning is completed.
1 Select the desired | SELECT LANGUAGE |
| 2 If the TV screen shows | - HELPFUL HINTS - |
language according to |
| snow noise and there | 1. PLEASE CHECK TO SEE IF | |
ENGLISH |
| SATELLITE IS PROPERLY | ||
|
|
|
| THE ANTENNA/CABLE/ |
the screen indication. | NEXT:PRESS CHK |
| is no operation for | CONNECTED. |
ESPAÑOL |
| 2. DID YOU PERFORM | ||
After that, the TV | DESPUÉS:PRESIONE CHL |
| more than 10 seconds, | “AUTO PRESET CH” ? |
APRÈS:PRESSEZ VOLK |
| PAGE OF THE OWNER’S | ||
| FRANÇAIS |
|
| 3. PLEASE REFER TO FRONT |
performs “AUTO |
|
| “HELPFUL HINTS” | MANUAL OR REAR PANEL |
|
| FOR SUPPORT LINE | ||
PRESET CH” to scan |
|
| appears. Follow the | INFORMATION. |
|
|
| ||
channels available for | – INITIAL SETUP – |
| instructions listed on |
|
the broadcasting in | PLEASE CONNECT ANTENNA |
| the screen. |
|
OR CABLE OR SATELLITE |
|
| ||
your area. | TO THIS UNIT. |
|
|
|
THEN PRESS CH K, |
|
|
| |
|
|
|
| |
| IN ORDER TO PERFORM |
|
|
|
| “AUTO PRESET CH”. |
|
|
|
|
|
|
|
|
When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the tuner stops on the lowest memorized channel.
Notes:
●In case no channel can be received by the channel scanning, “NO TV SIGNALS” is displayed on the screen. Turn off the unit and check the antenna connection, then follow step 1 again.
●If those settings do not work properly, please call our help line in the warranty.
SELECTING AUDIO/VIDEO INPUT
You can select external input jacks by pressing [GAME] on the remote control.
1 To use external input | 2 To return to TV channel | ||||
|
| GAME | 15 | ||
|
|
|
|
| |
| GAME |
|
| GAME |
|
|
|
|
|
|
|
Picture: GAME (ON)
Input: External
In the Game mode, you can use front input jacks with suitable picture adjustments for video games.
Notes:
●If you press [GAME] when the TV is off, the TV turns on and enters in Game mode.
●If you adjust another picture control while in Game mode, this mode will automatically be canceled.
Note:
●You can test if the remote control sends out the infrared signal with an AM radio. (Refer to “TROUBLESHOOTING GUIDE”.)
VIDEO AUDIO EARPHONE MENU | VOLUME | CHANNEL | POWER |
Infrared Sensor Window
POWER button
To turn TV on/off
CHANNEL ▲ /▼ buttons
To select channels
VOLUME X/Y buttons
To adjust volume
MENU button
To view
EARPHONE jack
AUDIO input jack
VIDEO input jack
Note:
●If some digits appear in the corner of the screen when the unit is turned on for the first time, press [POWER] without unplugging the power cord.
