Reset to the Default Setting (Except for PARENTAL Setting)
Press [SETUP] in the stop mode.
Select “INITIALIZE”.
Select “YES”.
To exit the menu
SETUP
STOP
<SETUP MENU>
QUICK SETUP
or 
QUICK SETUP
ENTER
or
INITIALIZE
Initialize?
SETUP
ENTER
Presstwice. Hint
• When you cancel |
PLAYER MENU | ENGLISH |
TV ASPECT | 4:3 LETTER BOX |
PROGRESSIVE | OFF |
DOLBY DIGITAL | BITSTREAM |
PLAYER MENU | ENGLISH |
TV ASPECT | 4:3 LETTER BOX |
PROGRESSIVE | OFF |
DOLBY DIGITAL | BITSTREAM |
NO
YES ENTER
to initialize at step |
, select “NO”. |
Information
Troubleshooting Guide
If this unit does not perform properly when operated as instructed in this Owner's Manual, check this unit consulting the following checklist.
PROBLEM | CORRECTIVE ACTION |
No power. | • Make sure the power plug is connected to an AC outlet. |
| • Make sure the power is turned on. |
DVD / VCR
This unit does not respond to the remote control.
Poor picture or noise.
Timer recording is impossible.
•Check if the power plug is connected to an AC outlet.
•Check the batteries in the remote control.
•Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote control.
•You have to be within 2 feet (7m) of this unit.
•Check if the right mode is selected. If it’s not in the right mode, press [DVD] or [VCR], whichever you need, on the remote control.
•Check if a cassette tape is in this unit.
•Tune your radio to an empty AM station so that you hear a lot of noises. Turn the volume up, then if you hear some signal sound from the radio in response to your pressing buttons on the remote control, the remote control is working.
•Press and hold any button on remote control toward a digital camera. The remote control is working if you confi rm infrared light through the digital camera.
•Interference signal may be received. Change the position and orientation of the unit.
•Make sure the Timer Recording is set correctly.
•Make sure 
indicator on the front panel lights up. If not, press
•Make sure the VCR clock is set correctly.
VCR
Cannot go into record mode.
Playback picture is partially noisy.
Cannot view a tape but the audio is OK.
No or poor, playback picture.
TV programs cannot be seen normally.
Video or color fades in and out when making a copy of a video tape.
Cannot remove the tape.
No picture.
Disc cannot be played.
•Make sure the tape has a record tab. If needed, cover the hole with adhesive tape.
•Activate this unit in VCR mode. Press [VCR] on the remote control so that the VCR OUTPUT light is lit.
•Adjust tracking control for a better picture by pressing [CHANNELL/K]] on the unit or [SKIP/CH. G/K, H/L] on the remote control.
•Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING”.
•Make sure the VCR is not in the Menu mode.
•Change the RF output channel to CH4. Then select the same channel on the TV.
•Fine tune your TV.
•
•Press [VCR].
•Press [VCR] on the remote control to activate it in the VCR mode. Check if the VCR OUTPUT light is lit, then set it to the TV position by pressing [VCR].
•You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
•Check if this unit is in the VCR mode. If not, press [VCR] on the remote control to switch the mode.
•Connect the video cable fi rmly.
•Insert a correct video disc that plays on this unit.
•Press [DVD] on the remote control. Check if the DVD OUTPUT light is lit. Then try other DVD features.
•Set PROGRESSIVE correctly. Turn it on only if your TV has progressive scan and you are using the Component Video connections between the unit and the TV. Disable progressive scan for all other connections. (See page 7.)
•Insert the disc.
•Clean the disc.
•Place the disc correctly with the label side up.
•Cancel the parental lock or change the control levels.
•Handle a disc with special care so that it does not have fi ngerprints, scratches, or dusts on its surface.
Information
DVD
No sound.
Distorted picture.
Audio or subtitle language does not match the setup.
The camera angle cannot be changed.
Audio or subtitle language cannot be changed.
“Prohibited icon” appears on the screen, prohibiting an operation.
•Connect the audio cable fi rmly.
•Turn the power of the audio component on.
•Correct the audio output settings.
•Correct the input settings on the audio component.
•Connect this unit directly to the TV.
•There are some cases where pictures may be slightly distorted, and those are not a sign of a malfunction.
•Although pictures may stop for a moment, this is not a malfunction.
•Check if the INTERLACE/PROGRESSIVE mode is set correctly according to your TV. See pages
•The selected language is not available for audio or subtitles on the DVD.
•The DVD does not contain sequences recorded from different camera angles.
•The DVD does not contain audio source or subtitles in the selected language.
•That operation is prohibited by this unit or the disc.
•Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual for details on correct operations.
•Playback from a desired track and random playback are not available during program playback.
•Some functions are prohibited on some discs.
–2 –EN
DVC841G_E8A04UD.indd 2 | 2006/02/08 18:6:1 |
