Symbol Technologies MC50 Cable Adapter Module

MC50 Integrator Guide3-12

Cable Adapter Module

This section describes how to and use the snap-on CAM with the mobile computer. The CAM snaps on to the bottom of the mobile

computer and can be easily removed when not in use.

Figure 3-10. Cable Adapter Module

When attached to the mobile computer, the CAM:

• Provides power for operating the mobile computer, with the appropriate power connection.

• Provides USB connection through the USB pass-through port for communication with a USB device, such as a host computer.

For communication setup procedures, refer to the MC50 Integrator Guide.

• Charges the mobile computer’s battery, when used with the appropriate power supply.

Use only a Symbol-approved power supply (p/n 50-14000-147) output rated 5.4 Vdc and minimum 3A. The

power supply is certified to EN60950 with SELV outputs. Use of alternative power supply will invalidate any

approval given to this device and may be dangerous.

Hinweis: Benutzen Sie nur eine von Symbol Technologies genehmigte Stromversorgung (Teilenr. 50-14000-147) mit einer

Ausgangsleistung von 5.4 V (Gleichstrom) und mindestens 3A. Die Stromversorgung ist nach EN60950 für die

Verwendung in SELV-Stromkreisen zertifiziert. Bei Verwendung eines anderen Netzteils werden alle für das Gerät

gewährten Genehmigungen außer Kraft gesetzt, und der Betrieb kann gefährlich sein.

Attaching and Removing

To attach, slide the CAM onto the bottom of the mobile computer, until it snaps into place.

Figure 3-11. CAM Installation

To remove the CAM pull the CAM from the mobile computer.

Power Port Communications Port

Contents

Main Page Page Page Contents About This Guide Chapter 1. Getting Started Chapter 2. Operating the MC50 Chapter 3. Accessories Page Page Page Page MC50 Documentation Set Configurations Chapter Descriptions Notational Conventions Related Documents Service Information Symbol Support Center Page Getting Started Page Page Accessories Table 1-1 lists the accessories available for the MC50 mobile computers. Table 1-1. Accessories Page Charging the Mobile Computer Battery Charging the Main Battery and Memory Backup Battery Using the Single Slot Cradle Figure 1-3. Charging in the Single Slot Serial Cradle Using the Four Slot Cradle Figure 1-4. Inserting the Mobile Computer(s) into the Four Slot Cradle Table 1-2. Mobile Computer LED Indicators Table 1-3. Single Slot Cradle Spare Battery Charging LED Indicators Page Starting the Mobile Computer Calibrating the Screen Page Setting Time and Date Checking Battery Status Page Magnetic Stripe Reader Figure 1-14. Swiping a Card Installing a Secure Digital Card Figure 1-15. SD Card Installation Page Page Operating the MC50 Page Using the Function Buttons Figure 2-1. Function Buttons Using the Stylus Using the Keypad Navigation Keypad Figure 2-2. Navigation Configuration Table 2-1. Navigation Keypad Actions QWERTY Configuration Figure 2-3. QWERTY Keypad Configuration Table 2-2. QWERTY Keypad Actions Table 2-2. QWERTY Keypad Actions (Continued) Table 2-3. QWERTY Keypad Input Modes Special Character Key Table 2-4. Special Characters Table 2-4. Special Characters (Continued) Key Mode Icon Page Entering Information Using the QWERTY Keypad LED Indicators Figure 2-7. MC50 LEDs Table 2-5. Mobile Computer LED Indicators Beeper Indicator The beeper on the mobile computer provides an audible indication for the scan status. Table 2-6. Beeper Indicator Data Capture Figure 2-8. Data Capture Configurations Linear Scanning Imaging Camera Scanning Considerations Figure 2-9. Linear Scanner Decode Zone MC50 User Guide2-16 Figure 2-10. Imager Decode Zone Depth of Field Linear Scanning Figure 2-11. Linear Scanning Figure 2-12. Linear Scanner Aiming Pattern Imager Scanning Figure 2-13. Imager Scanning Image Capture Figure 2-16. Image Capture Resetting the Mobile Computer Performing a Soft Reset Figure 2-17. Reset Button Performing a Hard Reset Infrared Communication Page Page Page Accessories Page Cradles Miscellaneous Snap-on Modules Headset Figure 3-1. Headset Connection Multi Media Card (MMC) / Secure Device (SD) Card Figure 3-2. MMC/SD Card Insertion Single Slot USB Cradle Charging the Mobile Computer Battery Figure 3-3. Mobile Computer Battery Charging Charging the Spare Battery Figure 3-4. Spare Battery Charging Table 3-1. Spare Battery LED Charging Indicators Four Slot USB Cradle Charging Figure 3-5. Mobile Computer Battery Charging Four Slot Ethernet Cradle Charging Figure 3-6. Mobile Computer Battery Charging Four Slot Spare Battery Charger Spare Battery Charging Figure 3-7. Four Slot Spare Battery Charger Table 3-2. Spare Battery LED Charging Indicators Magnetic Stripe Reader (MSR) Attaching and Removing Figure 3-8. MSR Installation Using the MSR Page Cable Adapter Module Figure 3-10. Cable Adapter Module Attaching and Removing Figure 3-11. CAM Installation Battery Charging Figure 3-12. CAM Power Connection USB Connection Page Universal Battery Charger (UBC) Adapter Battery Insertion and Removal Figure 3-14. UBC Adapter Figure 3-15. UBC Adapter LEDs Table 3-3. UBC Adapter Charge LED Status Indications Page Page Page Page Maintaining the MC50 Troubleshooting Table 4-1. Troubleshooting the Mobile Computer Table 4-1. Troubleshooting the Mobile Computer (Continued) Page Page Page MC50 Technical Specifications Table A-1. Environmental Parameters Table A-2. Technical Hardware Specifications Page Table A-2. Technical Hardware Specifications (Continued) MC50 Accessory Specifications Table A-3. Single-Slot USB Cradle Technical Specifications Table A-4. Four-Slot USB Cradle Technical Specifications Table A-5. Four-Slot Ethernet Cradle Technical Specifications Table A-6. Four-Slot Spare Battery Charger Technical Specifications Table A-7. UBC Adapter Technical Specifications Table A-8. Magstripe Reader (MSR) Technical Specifications Table A-9. Cable Adapter Module (CAM) Technical Specifications Page Glossary Page Page Page Page Page Page Page Page Page Page Page Page Page Index Numerics A B C D E F H L M N O P Page Tell Us What You Think...