Team Products PMP200XL Connecting the Inverter, Source of Power, Blown Automotive Fuses

PMP200XL Models

CAUTION

•The inverter is designed to operate from a 12-volt power source only.The unit will not operate from a 6-volt battery or a 24-volt battery. Do not attempt to connect the inverter to any other power nominal output voltage other than 12 volts or damage to the unit may occur. Any damage to the unit that occurs from operating the inverter from any power source greater than or less than 12 volts will automatically void the warranty.

•Do not attempt to extend or otherwise modify the 12-volt power cord attached to the inverter.

•110/120 volts can inflict serious injury, damage or death. Improper use of the inverter may result in property damage, personal injury or loss of life.

Connecting the Inverter

The inverter is equipped with a fused 12-volt power cord for connection to the power source.

1.Make sure that the ON/OFF power switch located on the front panel of inverter is in the OFF(O) position.

2.Connect the inverter to the power source by inserting the 12-volt power cord firmly into the cigarette lighter socket of your vehicle or other 12-volt DC power source.

3.Turn the inverter power switch to the ON(-) position.The GREEN LED Indicator Light should illuminate to confirm that power is running to the inverter.

4.Make sure that the device you intend to operate is turned OFF. Plug the cord from the equipment into the AC outlet located on the front panel of the inverter.

5.Turn the inverter power switch to the ON(-) position; then turn the

equipment ON.

Notes

•The audible alarm may make a momentary “chirp” when the inverter is turned ON (-) or OFF(O).This same alarm may also sound when the inverter is being connected to or disconnected from the 12-volt power source.This is normal.

•If the GREEN LED Indicator Light blinks when you first turn the inverter ON(-), this may indicate an interruption of the power supply. Simply turn the inverter OFF(O) and remove the 12-volt power cord from the cigarette lighter socket (or other 12-volt power source). Firmly re-insert the 12-volt power cord, then turn the inverter ON(-) again. If this does not fix the problem, try using a different 12-volt power source or check the cigarette lighter fuse.

3

PMP200XL_122205M.indd 8-9

Owner’s Manual

Source of Power

Most automobile and marine batteries will provide an ample power supply to the inverter for 30 to 60 minutes even when the engine is turned off. Actual time may vary depending on the age and condition of the battery and the power demand being placed on it by the equipment being operated.

If you decide to use the inverter while the engine is off, we recommend that you start the engine every 30 to 60 minutes and let it run for approximately 10 minutes to recharge the battery. It is also recommended that the device plugged into the inverter be turned OFF before starting the vehicle engine.

Although it is not necessary to disconnect the inverter when starting the vehicle engine, it may momentarily cease to operate as the battery voltage decreases. When the inverter is not supplying power, it draws very low amperage from the battery. It is recommend that the inverter always be disconnected when not in use.

Blown Automotive Fuses

Depending on the make and model of your automobile, running the power inverter near full capacity from your cigarette lighter socket may result in a blown automotive cigarette lighter fuse.This fuse will need to be replaced with the same type and size fuse. A blown automotive cigarette lighter fuse will not cause damage to your vehicle wiring.

Blown Inverter Fuses

Your power inverter is equipped with a 25-amp spade type fuse. With reasonable care, it should not be necessary to replace this fuse. In general, most blown fuses are the result of reverse polarity hook up of the inverter to a 12-volt power source (positive to negative and/ or negative to positive). If the fuse happens to blow, disconnect the appliance or equipment from the inverter immediately. Find the source of the problem, repair it and then install a new fuse of the same type and size located on the rear panel of the inverter.

Note

Always disconnect the power inverter from the 12-volt power source and make sure the inverter is turned OFF before replacing the fuse.

Safety and Usage Precautions

•For best operating results, place the inverter on a flat surface.

•Keep the inverter dry. Do not expose the inverter to rain or moisture.

•DO NOT operate the inverter if you, the inverter, the device being operated, or any surface that may come into contact with the inverter are wet. Water and other liquids can conduct electricity, which may lead to serious injury or death.

4

12/22/05 9:09:47 AM