IMPORTANT SAFETY INSTRUCTIONS
WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAU- TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:
1. READ AND UNDERSTAND ALL INSTRUCTIONS. |
2. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE |
PRODUCT. |
3. UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE CLEANING. |
DO NOT USE LIQUID CLEANER OR AEROSOL CLEANERS. USE A DAMP |
8. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT DISASSEMBLE |
THIS PRODUCT. BUT TAKE IT TO A QUALIFIED SERVICE FACILITY IF |
SERVICE OR REPAIR WORK IS REQUIRED. OPENING OR REMOVING |
COVERS MAY EXPOSE YOU TO DANGEROUS VOLTAGES OR OTHER |
RISKS. INCORRECT REASSEMBLY CAN CAUSE ELECTRIC SHOCK WHEN |
THE APPLIANCE IS SUBSEQUENTLY USED. |
9. UNPLUG THIS PRODUCT FROM THE WALL OUTLET AND REFER |
SERVICING TO QUALIFIED SERVICE PERSONNEL UNDER THE FOLLOW- |
ING CONDITIONS: |
CL2200 SERIES USERS GUIDE
2.4 GHz Two-Line Digital Cordless Guestroom Telephone
CLOTH FOR CLEANING. |
4. DO NOT USE THIS PRODUCT NEAR WATER, FOR EXAMPLE, NEAR A |
BATHTUB, WASH BOWL, KITCHEN SINK OR LAUNDRY TUB, IN A WET |
BASEMENT, OR NEAR A SWIMMING POOL. |
5. DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND OR |
TABLE. THE PRODUCT MAY FALL, CAUSING SERIOUS DAMAGE TO THE |
PRODUCT. |
6. SLOTS AND OPENINGS IN THE CABINET AND THE BACK OF BOTTOM |
ARE PROVIDED FOR VENTILATION, TO PROTECT IT FROM OVERHEATING. |
THESE OPENINGS MUST NOT BE BLOCKED OR COVERED. THE OPENINGS |
SHOULD NEVER BE BLOCKED BY PLACING THE PRODUCT ON THE BED, |
SOFA, RUG OR ANY OTHER SIMILAR SURFACE. THIS PRODUCT SHOULD |
NEVER BE PLACED NEAR OR OVER A RADIATOR OR HEAT REGISTER. |
THIS PRODUCT SHOULD NOT BE PLACED IN A |
UNLESS PROPER VENTILATION IS PROVIDED. |
7. NEVER PUSH OBJECTS OF ANY KIND INTO THIS PRODUCT THROUGH |
CABINET SLOTS AS THEY MAY TOUCH DANGEROUS VOLTAGE POINTS |
OR SHORT OUT PARTS THAT COULD RESULT IN A RISK OF FIRE OR |
ELECTRIC SHOCK. NEVER SPILL LIQUID OF ANY KIND ON THE PRODUCT. |
- WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED OR FRAYED. |
- IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT. |
- IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER. |
- IF THE PRODUCT DOES NOT OPERATE NORMALLY BY FOLLOWING |
THE OPERATING INSTRUCTIONS. ADJUST ONLY THOSE CONTROLS THAT |
ARE COVERED BY THE OPERATING INSTRUCTIONS, AS IMPROPER |
ADJUSTMENT OF OTHER CONTROLS MAY RESULT IN DAMAGE, AND |
MAY REQUIRE EXTENSIVE WORK BY A QUALIFIED TECHNICIAN TO |
RESTORE THE PRODUCT TO NORMAL OPERATION. |
- IF THE PRODUCT HAS BEEN DROPPED OR THE CABINET HAS BEEN |
DAMAGED. |
- IF THE PRODUCT EXHIBIT A DISTINCT CHANGE IN PERFORMANCE. |
10. AVOID USING A TELEPHONE (OTHER THAN A CORDLESS TYPE) |
DURING AN ELECTRICAL STORM. THERE MAY BE A REMOTE RISK OF |
ELECTRIC SHOCK FROM LIGHTNING. |
11. DO NOT USE THE TELEPHONE TO REPORT A GAS LEAK IN THE |
VICINITY OF THE LEAK. |
PLEASE SAVE THESE INSTRUCTIONS
INCLUDED IN YOUR PACKAGE
Cordless Handset | AC Adapter |
Base Unit | User Guide |
NiMH Battery | |
Rubber Battery Screw Cover | |
Phillips Screw | Clear Plastic Overlay |
PREPARING TO USE THE CL2200 SERIES
1.Prepare to install the battery into the cordless handset by firmly pressing down on the top of the battery cover and sliding it off. If cover is secured with a screw, remove the screw first.
2.Locate the lightly embossed numbers “1” and “2” on the battery’s plastic connector.
3.Insert the battery connector into the handset’s connector with the embossed numbers facing up.
Note: The handset may “beep” when the battery is connected. This is not an indication that the telephone is ready to use. To obtain optimal perform- ance of the telephone, be sure to charge the battery for 15 to 20 hours.
4. Replace the battery compartment cover and retaining screw.
3.Ensure that the handset charging contacts at the bottom of the handset are making good contact with the base unit’s charging contacts.
CLEANING THE BATTERY CONTACTS
To maintain a good charge, it is important to clean all charging contacts on the handset and base unit. Use a pencil eraser or other contact cleaner. Do not use any liquids or solvents.
BATTERY SAFETY INSTRUCTIONS
1.Use only
2.Dispose of used batteries according to local codes pertaining to NiMH batteries.
3.Do not dispose of batteries in fire, as they may explode
4.Charge the telephone's batteries only while in the telephone handset, and only by using the telephone base unit to charge. Do not attempt to remove the batteries and charge them in a separate charging unit.
5.Do not
CONTACTING TELEDEX
Telephone (408)
(800)
Internet www.teledex.com store.teledex.com
sales@teledex.com
Postal Mail
6311 San Ignacio Avenue
San Jose, CA 95119 USA
CL2200 SERIES DIAGRAM | Part Number |
| Copyright © 2003 Teledex LLC |
| ALL RIGHTS RESERVED |
5.Insert the provided rubber screw cover.
6.Turn the telephone base so the back panel is facing you. Insert either end of the
7.Insert the other end of the cable into the jack on the AC adapter labeled PHONE.
8.Insert one end of the
9.Insert the other end of this line cord into a telephone jack.
10.Plug the AC adapter into an unswitched electrical outlet.
11.Once your telephone is connected, remove the plastic overlay and place the paper faceplate over the keys. Replace the plastic overlay by hooking the tabs on the overlay into the recessed slots located on both sides. The overlay is easiest to insert when the left or right side tabs are inserted first, and the middle of the overlay is slightly bowed to allow for insertion of the other tabs.
12.Place the cordless handset on the base unit.
CHARGING THE BATTERY
The rechargeable Nickel Metal Hydride (NiMH) battery must be fully charged before using the phone for the first time. It is recom- mended that that battery pack be charged for approximately 15 to 20 hours, without interruption, before use. To charge the battery, place the handset, keypad down, in the base unit. Make sure the CHARGE LED on the base lights. If the LED does not light:
1.Ensure that the AC adapter is plugged in.
2.Ensure that the AC adapter is not plugged into a switched electrical outlet.
ADJUSTING THE RING VOLUME
The up and down volume keys will adjust the ringer volume of the telephone. Additionally, the CL2200 series telephone has an optional “ascending” ring volume mode, where the ring volume begins at the lowest setting, then automatically rings louder with each successive ring during an incoming call. To select the ascending ring volume mode, follow these steps:
For Line 1:
Press the FLASH key; then the 4 key; then the STORE key, then the number 1 on the keypad.
For Line 2:
Press the FLASH key; then the 4 key; then the STORE key, then the number 2 on the keypad.
ADJUSTING SPEAKERPHONE VOLUME
The speakerphone has eight (8) levels. When the speakerphone is activated, the volume is initially set at level six (6). To adjust the speakerphone volume, locate the volume up/down keys, located on the front surface of the phone below the keypad. Pressing the “down” arrow key will decrease the volume level, while pressing the “up” arrow key will increase it.
ADJUSTING HANDSET RECEIVE VOLUME
The handset has four (4) volume levels. The volume is initially set at level two (2). To adjust the handset volume, locate the volume up/down keys, located on the handset, below the “#” key.
Pressing the “minus”
