ECM Specifications
Model Number * | |||||||||
CFM from .1 |
|
|
|
|
|
|
| ||
| A/C Tonnage Selection |
|
|
|
|
|
| ||
Cooling |
| A/C | Continuous | A/C | Continuous | A/C | Continuous | A/C | Continuous |
| CFMs | Fan | CFMs | Fan | CFMs | Fan | CFMs | Fan | |
(100 cfm | 2 ton | 800 | 500 | 800 | 500 | 800 | 500 | 800 | 500 |
steps | |||||||||
available | 2.5 ton | 1000 | 500 | 1000 | 500 | 1000 | 500 | 1000 | 500 |
for A/C) | 3 ton | 1200 | 600 | 1200 | 600 | 1200 | 600 | 1200 | 600 |
| |||||||||
| 3.5 ton | 1400 | 700 | 1400 | 700 | 1400 | 700 | 1400 | 700 |
| Air Temperature Rise Selection |
|
|
|
|
|
| ||
|
| Heating CFM | Heating CFM | Heating CFM | Heating CFM | ||||
Heating | 57° Rise |
| 1400 |
| — |
| 1400 |
| — |
(at approx. | 63° Rise |
| 1260 |
| 1500 |
| 1260 |
| 1500 |
rated input |
|
|
|
| |||||
69° Rise |
| 1162 |
| 1350 |
| 1162 |
| 1350 | |
BTU) |
|
|
|
| |||||
| 75° Rise |
| 1050 |
| 1245 |
| 1050 |
| 1245 |
| 83° Rise |
| 938 |
| 1125 |
| 938 |
| 1125 |
The standard motor size may not support this cfm at high static pressures. * Model numbers end with ‘E’ to signify ECM motor.
Additional Features
General
•Eliminates the need for air temp thermostat to control fan cycling by using time instead.
•Selectable blower
•Three blower operating choices: HEAT, COOL & FAN for best efficiency for each mode.
•Reduces A/C blower speed 50% on demand to increase dehumidification.
•Cooling blower delays of 10 seconds on, and 45 seconds off to enhance cooling comfort and efficiency.
Cycle Control
•4 minute minimum A/C off time to reduce
•A high limit will cause the blower run at the selected HEAT speed. It will then run for the HEAT turn off time afterwards in the absence of a HEAT call.
•Blower operation will “time out” before mode is switched between HEAT & COOL to prevent stress related evaporator failures.
•Burner
Speed Control
•Selectable air temperature (heat) rise from Return to Supply Plenum (choose from: 63, 69, 75 and 85ºF)
•Selectable CFM rates for matching A/C tonnages. These CFM selections support from 2.0 to 3.5 tons.
•Maximum CFM’s are limited by the maximum RPM of the ECM motor and the duct static pressure. Please refer to the manual addendum for guidelines.
Diagnostics
• Control Input LED’s indicate active thermostat input lines.
• Diagnostic LED indicate:
1.Active Operation (turn full on during burner or compressor operation)
2.A HIGH LIMIT condition. (flash on/off at 2 ½ times per second)
Form No. PL81410021002 - 6/05 - 20Ms Printed in the U.S.A.
© 2005 Thermo Pride - North Judson, IN Phone: