Thiel Audio Products SS3, SS4, SW1 manual Feet, Thiel, SmartSub

Feet

The SS2 and SS3 are supplied with four pointed, screw-in feet that can be used to provide firmer coupling to the floor for slightly better sound quality and to prevent the unit from moving during use. Please be advised that their use can put dents in hardwood floors. They are screwed into the bottom of the unit, and should be individually adjusted until the unit is firmly seated onto the floor without rocking. Then tighten each of the back-nuts to lock the feet in place.

The SS4 has four large castors and four large stabilizer feet built into the bottom of its cabinet. The unit is supplied with the stabilizers screwed into the bottom so that the unit can be rolled to its desired location. If desired, the stabilizers can be screwed down beyond the point where they are touching the floor in order to lift the SS4 off of its wheels and allow the weight to be connected through the stabilizers to the floor. This will prevent the unit from moving on its wheels. The stabilizers should be adjusted individually so that the unit does not rock and sits firmly.

THIEL

This light and the one on the front of the subwoofer will glow green if the amplifier is currently operational, and red for 5 seconds during start-up or if the amplifier is set for auto-on that is not currently activated. It will flash in various colors and patterns when heat or line voltage is a problem.

SmartSub®

Patents Pending

Side Wall Distance	meters
Rear Wall Distance	meters
LFE Level

Increase

Select

Set this adjustment to match the distance from the side of the subwoofer to the side wall of the room (in meters).

Set this adjustment to match the distance from the rear of the subwoofer to the rear wall of the room (in meters).

This level adjustment functions only for the LFE input. If you are not using the LFE input, set this to minimum (OFF). If the subwoofer volume is set by the processor then a good starting point is 90.

This displays the current setting of the adjustment designated by the light above.

This button increases the active setting.

This button selects which setting is active.

	Decrease
WARNING
TO PREVENT FIRE OR SHOCK HAZARD
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE	LFE Input
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
REPLACE FUSE ONLY WITH SAME RATING

CAUTION		!
RISK OF ELECTRIC SHOCK				LFE Output
DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR
ATTENTION
POUR EVITER TOUS RISQUES DE FEU OU DE CHOC ELECTRIQUE
N'EXPOSEZ PAS CET APPAREIL A L'HUMIDITE				Normal Input
AUCUN COMPOSANT NE PEUT ETRE REMPLACE PAR L'UTILISATEUR
VEULLEZ CONTACTER LE SERVICE APRES VENTE AGREE
REMPLACER LE FUSIBLE PAR UN AUTRE DE LA MEME VALEUR
				Normal Output
Model
Ser No
Voltage
Fuse				Trigger On
120v 8A
240v 4A		Off	On	On
Slo-blow
				Auto
THIEL Audio •	1026 Nandino Boulevard • Lexington, Kentucky • USA			• www.thielaudio.com
See page 14 for fuse replacement Power cord plugs here				Turn power on here

This button decreases the active setting.

Connect an input cable to this connector if the subwoofer is being used for the processor’s subwoofer output.

If the LFE input is used, this connector can connect to an additional subwoofer.

Connect an input cable to this connector if the subwoofer is being driven by a crossover or Integrator.

If the Normal input is used, then this connector can be used to connect to an additional subwoofer.

DC voltage (5-25 volts) to this jack will turn the amplifier on if the auto/on switch is set to auto. Removing the voltage turns the amp off.

Setting this switch to On turns the amplifier on (after a 3 second start-up delay) provided that the main power switch is on. The Auto position allows the amplifier to automatically turn on when it detects an input or a trigger.

11