www.timex.com
THANK YOU FOR PURCHASING YOUR TIMEX® STOPWATCH.
Please read instructions carefully to understand how to operate your Timex® stopwatch.
FEATURES AND BASIC OPERAT I O N
•Time of day with 12- or
•Day and date
•2nd time zone
•Optional hourly chime
•
•Chronograph recall with date stamp, best lap, and average lap time for each run
•Optional
•Speed calculation
•
•Pacer
•7 weekly alarms and one daily alarm
•INDIGLO®
Press MODE repeatedly to step through modes: Time, Chrono, Speed, Recall, Timer, Pacer, Weekly Alarm, and Daily Alarm. Unit displays mode name for 2 seconds before switching to mode shown.
AC T I VAT I O N
Unit is shipped in “OFF” mode to preserve battery life. To activate unit, press and hold all five buttons simultaneously until STOP indicator disappears, about 4 seconds. When buttons are released, unit is ready for use.
TIME
Time mode provides time and date like a digital watch. Press MODE repeatedly until TIME appears.
To set time and date:
1)Press and hold RESET/ADJUST. Seconds flash. Press START/STOP to round time up or down to nearest minute, setting seconds to zero.
2)Press MODE. Minutes flash. Press START/STOP to change minutes; hold button to scan values.
3)Press MODE. Hour flashes. Press START/STOP to change hour (including AM/PM).
4)Press MODE. Day flashes. Press START/STOP to change day.
5)Press MODE. Month flashes. Press START/STOP to change month.
6)Press MODE. Year flashes. Press START/STOP to change year.
7)Press MODE. Time format flashes. Press START/STOP to select 12- or
8)Press RESET/ADJUST, at any step, when done setting.
Press and hold LAP/NEXT to see TIME 2, a 2nd time zone. “TIME 2” appears on display. Continue holding button to switch time and date to TIME 2. After switching, set TIME 2 using procedure above. Press and hold LAP/NEXT to see or switch back to home time from TIME 2.
Press START/STOP to turn hourly chime on/off. When on, bell icon | appears and unit chimes |
on every hour. |
|
CHRONOGRAPH
This mode provides a chronograph (stopwatch) function. This mode is only available when Speed mode is not in use. Press MODE repeatedly until CHRONO appears.
To start, press START/STOP. Chrono counts up by hundredths of a second. Hours are shown in upper right part of display (“00H” initially).
To stop, press START/STOP. To resume, press START/STOP again.
While chrono is running, press LAP/NEXT to take a lap/split. Lap time is displayed with lap number for 9 seconds, while chrono continues to run.
At end of run, press START/STOP. Last lap time is displayed for 9 seconds followed by total time. Press LAP/NEXT or RESET/ADJUST to immediately display total time.
Once chrono is stopped and total time is displayed, to store run and go to next (new) run, press and hold LAP/NEXT, or to reset chrono (clear last run), press and hold RESET/ADJUST. Run number is shown in upper right part of display. Stored runs may be recalled in Recall mode, described below.
Chrono continues to run if you exit mode.
NOTES:
•To see amount of remaining memory, when chrono is reset (zero), press and hold LAP/NEXT.
•Chrono counts up to 24 hours and starts over at zero.
SPEED
Speed mode calculates speed of individual laps. This mode is only available when chrono is reset (zero). Press MODE repeatedly until SPEED appears.
To use Speed mode, you must set lap distance:
1)Press and hold RESET/ADJUST. 1/100 mile digit flashes. Press START/STOP to change value; hold button to scan values.
2)Press MODE. 1/10 mile digit flashes. Press START/STOP to change value.
3)Use MODE and START/STOP as above to set other digits.
4)Press RESET/ADJUST, at any step, when done setting.
Mode operates like Chrono mode, except speed is displayed briefly when timing is stopped or lap/split is taken. When run is stored, speed data is included. See RECALL section.
RECALL
Recall mode allows you to view data of stored runs from Chrono or Speed mode. This mode is only available when stopwatch is not running. Press MODE repeatedly until RECALL appears.
Upon mode entry, amount of remaining memory is displayed.
If no data is stored, “NO DATA” is displayed. Otherwise, last run is displayed. Run number and date of run are shown.
To select another run to recall, press LAP/NEXT. This may be done at any point in recall sequence.
To recall run, press START/STOP repeatedly to step through data: run date, lap distance (if run was done in Speed mode), lap times, total time, best lap time, and average lap time. If run was done in Speed mode, speed is shown alternating with the lap times.
To delete run from memory, press and hold RESET/ADJUST. To clear all of memory, continue holding RESET/ADJUST.
TIMER
Timer mode provides a countdown timer with alert. Press MODE repeatedly until TIMER appears.
To set countdown time:
1)Press and hold RESET/ADJUST. Seconds flash. Press START/STOP to change seconds; hold button to scan values.
2)Press MODE. Minutes flash. Press START/STOP to change minutes.
3)Press MODE. Hours flash. Press START/STOP to change hours.
4) Press LAP/NEXT, at any step, to select action at end of countdown, repeat | or count up | . |
5)Press RESET/ADJUST, at any step, when done setting. To start timer, press START/STOP.
To pause countdown, press START/STOP. To resume countdown, press START/STOP, or to reset countdown, press LAP/NEXT when timer is stopped.
Watch beeps when countdown ends (timer reaches zero). Press any button to silence. If no button is pressed, alert will sound for 20 seconds. If timer was set to repeat, timer repeats countdown indefinitely. Otherwise, it begins counting up.
Timer continues to run if you exit mode.
