Timex W-14 warranty Chime, Split Timing

Register your product at

www.timex.com

W-14820-095023 NA

THANK YOU FOR PURCHASING YOUR TIMEX WATCH.

EXTENDED WARRANTY

Available in U.S. only. Extend your warranty for an additional 4 years from date of purchase for $5. You can pay with AMEX, Discover, Visa or MasterCard by calling 1 800-448-4639 during normal business hours. Payment must be made within 30 days of purchase. Name, address, telephone number, purchase date, and 5-digit model number required. You can also mail a check for $5 to: Timex Extended Warranty, P.O. Box 1676, Dept. EF, Little Rock, AR 72203.

Please read instructions carefully to understand how to operate your Timex watch.

Your model may not have all of the features described in this booklet.

GENERAL OPERATION

Press 1 to cycle through time/date, chronograph, countdown timer, alarm. Compass function available in all modes except alarm by pressing 3.

TIME-DATE

A. From TIME AND DATE mode, press/hold 2 Þrmly to set. B. SECONDS will ßash. Press 4 to return to zero.

C. Press 1 to set HOURS, MINUTES, DAY, MONTH, DATE, NORMAL (12- hour) or MILITARY (24-hour) TIME, BUTTON BEEP (on or off). Selected item will ßash.

D. Press 4 to advance selected item. Note AM or PM when setting HOURS (12-hour time only). Hold 4 to advance rapidly.

E. Press 4 to exit SET procedure.

ALARM & CHIME

A. Press 2 to begin setting. HOURS will ßash.

B. Press 4 to advance hours. Note AM or PM designation.

C. Press 1, TENS OF MINUTES will ßash. Press 4 to advance. D. Repeat for MINUTES. Press 2 to exit SET mode.

NOTE: After every new alarm setting, ALARM will be armed when

you exit from SET mode by pressing 2. The symbol will appear, indicating ALARM is armed.

Chime

A. Press 4 to alternate between ON and OFF. This indicates ALARM is armed and active. It will sound for 20 seconds, but can be silenced by pressing any button.

CHRONOGRAPH

A. Press 4 to begin timing.

NOTE: You can leave CHRONOGRAPH mode while it is running. In TIME OF DAY mode, stopwatch icon on left side of middle display 8 indicates chronograph is running.

B. Press 2 to stop.

C. Press 4 to resume timing OR Press and hold 2 to reset.

Split Timing

A. Begin timing--press 4 as above. Press 4 to temporarily freeze display and measure a split. Lap # will show in upper display (7), watch will continue counting.

B. Press 4 to resume showing running lap.

C. When event ends, press 2. Watch will end timing. Display will show Þnal split time (total event time).

D. Press/hold 2 to reset chronograph to zero.

NOTE: To pause during split timing (time is not accumulating), press 2. Press 4 to resume, or press/hold 2 to reset to zero. Displays minutes, seconds and hundredths up to 100 minutes (99:59.99).

COUNTDOWN TIMER

A. Press 2 to increase MINUTES. Hold to increase rapidly up to 99 minutes.

B. Press 4 , countdown begins. You may switch to another mode without affecting timer. (hourglass symbol appears in TIME OF DAY window while timer is counting.) Even in another mode, timer will beep when it reaches zero. Press any button to cancel beep.

C. To stop timer, press 2 (MUST BE IN TIMER MODE).

D. Press 4 to continue, or press 2 to reset timer to original setting.

COMPASS CALIBRATION

IMPORTANT: Watch must be calibrated before using to find directions!

This product incorporates the magnetic sensor technology of PRECISION NAVIGATION, INC., Mountainview, CA.

A compass works with the EarthÕs magnetic Þeld; therefore you must not be in or near large metallic objects (such as automobiles, bridges, etc.) or objects that give off electromagnetic radiation (such as TV sets), which could interfere with the watchÕs calibration or use.

You cannot calibrate or obtain accurate readings from inside buildings, trains, or airplanes.

Typical accuracy of wrist-worn instruments is within +/- 10 degrees. To optimize accuracy, an optional two-step calibration is recommended, and discussed in further detail below. In cali- brating and taking subsequent headings, it is important as with all compasses, to maintain a level plane relative to the earthÕs horizon. Performing calibration or taking a heading when the watch is not level can result in large heading errors.* Care must also be taken to avoid areas which may exhibit higher than normal concentrations of hard and soft iron. This is especially true given the relatively weak magnetic Þeld of the earth, relative to other sources of magnetic Þelds. Failure to do so can result in inaccurate headings. Whenever a heading value is suspect, a new calibration should be performed. It is also recommended that calibration be performed in the intended area of use, or when the watch has been stored for an extended length of time.

Care should be taken to avoid storing the watch near any source of magnetism (computers, appliances, TVÕs, etc.), as the watch can take on a magnetic charge and render subsequent headings inaccurate. When the watch is suspected of having taken on a magnetic charge, a new calibration should be performed.

Applying good maintenance procedures, periodic calibration, and observing the guidelines as outlined above will help to insure headings are accurate to within the limitations of the imme- diate environment.

A.To calibrate for magnetic north, press and hold HEADING (from TIME OF DAY mode only) until ROTATE WATCH TWICE appears in the display.