11. Technical Specifications
Frequency response (1) +/- 3dB | 70Hz - 20kHz |
|
| |
Recommended Amplifier Power | up to 180 watt / 8 ohm |
|
| |
Power Handling | Average(2) | Programme Peak (10ms) |
| |
| 90 watt | 180 watt | 360 watt |
|
Sensitivity (1) |
|
|
|
|
2.83 volt @ 1m | 90dB | 93dB (half space) |
| |
Maximum SPL (3) | Average | Peak | Average (half space) | Peak (half space) |
@ 1m | 109dB | 115dB | 112dB | 118dB |
Maximum SPL (3) With THP30 Transformer | Average | Peak | Average (half space) | Peak (half space) |
@ 1m | 104 dB | 110dB | 107dB | 113dB |
Transformer (i6T AW) | Max. Insertion loss | 1.1 dB 35Hz – 21kHz +/- 2dB | ||
| Primary Taps | 30,15, 7,1.5 watt |
| |
| Voltage Taps | 70.7V & 100V |
| |
Impedance | Nominal | 8 ohm |
|
|
| Minimum | 6 ohm |
|
|
DI Averaged (PCQ) | 7.41, 250 Hz - 16 kHz |
|
| |
@ 1kHz (ISO) | 6.1 |
|
|
|
@ 2kHz (ISO) | 6.3 |
|
|
|
@ 4kHz (ISO) | 9.7 |
|
|
|
@ 8kHz (ISO) | 9.6 |
|
|
|
@ 16kHz (ISO) | 13.6 |
|
|
|
Q Averaged (PCQ) | 7.74, 250 Hz - 16 kHz |
|
| |
@ 1kHz (ISO) | 4.1 |
|
|
|
@ 2kHz (ISO) | 4.3 |
|
|
|
@ 4kHz (ISO) | 9.3 |
|
|
|
@ 8kHz (ISO) | 9.1 |
|
|
|
@ 16kHz (ISO) | 22.9 |
|
|
|
Driver Complement | 1 x 6.5” (165mm) Constant Directivity Dual Concentric | |||
Crossover Point | 1.6 kHz |
|
|
|
Enclosure | 11 litre, vented polyethylene |
| ||
Finish | Charcoal or | White |
|
|
Protective Grille | Perforated Aluminium |
|
| |
Connectors | 2 x 4mm binding posts |
|
| |
Fittings | 2 x M8 inserts for Yolk Bracket |
| ||
| 4 x M6 inserts on rear of cabinet |
| ||
Dimensions | 344mm (H) x 250mm (W) x 225mm (D) |
| ||
| 13.54” (H) x 9.84” (W) x 8.86” (D) |
| ||
Weight | 5.5 Kg (12.1 lbs) |
|
| |
Shipping Dimensions | 400mm (H) x 500mm (W) x 300mm (D) |
| ||
| 15.75” (H) x 19.69” (W) x 11.8” (D) |
| ||
Shipping Weight | 13Kg (28.6 lbs.) |
|
| |
NOTES:(1) Average over stated bandwidth. Measured at 1m on axis, in an anechoic chamber.
(2)Long term power handling capacity as defined in EIA standard RS - 426A.
(3)Unweighted pink noise input, measured at 1m
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications which Tannoy reserve the right to alter without prior notice.
Please verify the latest specifications when dealing with critical applications.
