ENGLISH
II. INSTALLATION
IMPORTANT
IT IS THE CUSTOMER’S RESPONSIBILITY TO REPORT ANY CONCEALED OR
A.Installation Options and Kit Availability
Your hot food server is shipped from the factory with 4”
• | P/N ACCHFSC | Casters kit (for |
• | P/N ACCHFS6 | 6” legs kit (for |
• | P/N ACCHFS9 | 9” legs kit (for |
All hot food server installations REQUIRE the unit(s) to be mounted on legs or casters prior to operation. The allowed installation configu- rations are:
| Supplied | Casters | 6” legs | 9” legs |
| 4” legs | kit | kit | kit |
|
|
|
|
|
Single unit | YES | YES | YES | YES |
|
|
|
|
|
YES | YES | YES | YES | |
|
|
|
|
|
NO | YES | YES | YES | |
NO | YES | YES | YES |
CAUTION
STACKING MORE THAN FOUR SERVERS IS NOT PERMITTED.
B.Legs/Casters Assembly
1.To install the supplied 4”/102mm legs
2.To install an optional Legs Kit or Casters Kit, refer to the instruc- tions provided with the Kit.
C.Stacking the Hot Food Servers (2-4 units only)
D.Electrical Connection
IMPORTANT
THE ELECTRICAL CONNECTION TO THE HOT FOOD SERVER REQUIRES A CIRCUIT BREAKER/FUSED DISCONNECT. ELEC- TRICAL SPECIFICATIONS ARE LISTED ON THE SERIAL PLATE (SHOWN IN FIGURE 4), AND IN SECTION I OF THIS MANUAL.
CONSULT ALL APPLICABLE NATIONAL AND LOCAL CODES FOR FURTHER ELECTRICAL CONNECTION REQUIREMENTS.
1.Before proceeding with the electrical connection, check the fol- lowing for each hot food server:
a.Check that the electrical supply matches the hot food server’s requirements. Refer to the serial plate (Figure 4) and to the electrical specifications shown in Section 1 of this Manual.
b.Check that the appropriate receptacle is available for the power cord plug.
WARNING
ENSURE THAT BOTH THE CIRCUIT BREAKER/FUSED DIS- CONNECT AND THE POWER ON/OFF (I/O) SWITCH ARE IN THE OFF (“O”) POSITION BEFORE PROCEEDING.
WARNING
ENSURE THAT ANY PACKING MATERIAL HAS BEEN RE- MOVED FROM INSIDE THE CABINET AND FOOD TRAY.
3.Insert (each) power cord plug into its receptacle.
Figure 2
CAUTION
If you have installed the optional Casters Kit, check that the casters are locked before stacking the hot food servers.
Perform the following steps, starting with the server that has legs/ casters installed:
1. | Remove the two screws that hold the control panel in place. Be |
| sure to retain the screws. See Figure 2. |
2. | Gently pull the control panel out from the front of the unit and |
| allow it to hang by the wiring. DO NOT stretch or disconnect the |
| wiring! See Figure 2. |
3. | Remove the cap plug from the top panel of the unit. To remove |
| the plug, bend the tines on the underside of the plug in towards |
| the center using a pair of pliers. Then, lift the cap free and dis- |
| card it. See Figure 3. |
4. | Place a hot food server atop the unit. Check that all four sides of |
| the units are aligned. |
5. | Attach the two units together by inserting the supplied 3/8” bolt |
| from inside the control panel opening of the lower server, as shown |
| in Figure 4. The bolt passes through the hole in the top panel |
| and into the threaded leg hole in the floor of the upper unit. Tighten |
| the bolt to a LOOSE fit to allow the position of the units to be |
Control panel
mounting screws
Figure 3
1. Cap plug
shown in place
Underside
of server
3. After stacking,
insert bolt
through cap hole
Control panel opened
2.To remove, bend tines in
towards
center of plug
| adjusted. |
6. | At the rear of the upper server, remove the screws from BOTH |
| bottom rear corners, as shown in Figure 4. Then, loosen (do not |
| remove) the two screws on the lower server that hold the stack- |
| ing clips in place. |
7. | Reposition the stacking clips as shown in Figure 4, and replace |
| the two screws that you removed in Step 6. Tighten all four |
| screws. |
8. | Tighten the 3/8” bolt (that you installed in Step 5) to secure the |
| units together. |
9. | Replace the control panel, and fasten it in place with its screws. |
10. Repeat Steps |
plug will remain in place on the top server in the stack. | 2 |
Figure 4 (left side shown - reposition brackets on BOTH sides)
1. Remove | 3. Reposition |
|
Data plate
2. Loosen
4.Replace 5. Tighten