Toshiba 19A25 ANTENNA/CABLE TV Connections, Connection to Other Equipment, TV/VIDEO Selection

ANTENNA/CABLE TV CONNECTIONS

Choose one of the following seven connections, based on your equipment and service:

Combination VHF/UHF antenna

Single 75 ohm cable	To ANT input
	on back of TV

(or)
Single 300 ohm twin-lead wire*	To ANT input
	on back of TV
*For best performance, if you have a splitter connected, remove	TRANSFORMER
the splitter and connect the single wire to the transformer,	(not supplied)
and then to the TV’s antenna input (as illustrated here).

Separate VHF and UHF antennas or

Combination VHF/UHF antenna with separate cables/wires

UHF Antenna

300 ohm twin-lead wire	To ANT input
VHF Antenna	on back of TV
75 ohm cable	COMBINER
	(not supplied)

(or)

UHF Antenna

300 ohm twin-lead wire	To ANT input
	on back of TV
VHF Antenna
300 ohm twin-lead wire*	COMBINER
	(not supplied)
TRANSFORMER
(not supplied)

Cable TV service						To ANT input
From cable						on back of TV
TV service
(or)						To ANT input
From cable						on back of TV
TV service		CONVERTER/ DESCRAMBLER
(or)						To ANT input
From cable		CONVERTER/ DESCRAMBLER				on back of TV
TV service	SPLITTER		A / B SWITCH	A	B

Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)

Connect the 75 ohm cable from a combination VHF/UHF antenna to the antenna jack.

If your combination antenna has a 300 ohm twin-lead wire, use the 300-75 ohm matching transformer (not supplied).

Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-leads)

Connect the UHF twin-lead wire to a combiner (not supplied). Connect the VHF twin-lead to the 300-75 ohm matching transformer (not supplied). Attach the transformer to the combiner. Attach the combiner to the antenna jack.

Separate VHF/UHF antennas

Connect the 75 ohm cable from the VHF antenna and the UHF antenna twin-lead to a combiner (not supplied). Attach the combiner to the antenna jack.

NOTE: If your VHF antenna has a twin-lead wire, use the 300-75 ohm matching transformer (not supplied), then connect the trans- former to the combiner.

For subscribers to basic cable TV service

For basic cable service not requiring a converter/descrambler box, connect the Cable TV 75 ohm coaxial cable directly to the antenna jack on the back of the television.

For subscribers to scrambled cable TV service

If you subscribe to a cable service that requires the use of a converter/descrambler box, connect the incoming cable to the converter/descrambler box and connect the output of the box to the antenna jack on the back of the television. Follow the connections shown at left. Set the television to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box to select channels.

For subscribers to unscrambled basic cable with scrambled premium channels

If you subscribe to a cable service in which basic cable channels are unscrambled and premium channels require the use of a converter/descrambler box, you may wish to use a two-set signal splitter (sometimes called a “two-set coupler”) and an A/B switch box from the cable installer or an electronics supply store. Follow the connections shown at left. With the switch in the “B” position, you can directly tune any nonscrambled channels on your TV. With the switch in the “A” position, tune your TV to the output of the converter/descrambler box (usually channel 3 or 4) and use the box to tune scrambled channels.

This television has an extended tuning range and can tune most cable channels without using a cable company supplied converter box. Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device, which is generally provided by the cable company.

CONNECTION TO OTHER EQUIPMENT

The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model and features of each component. Check the owner’s manual provided with each component for the location of video and audio inputs and outputs. The following connection diagrams are offered as suggestions. You may need to modify them to accommodate your particular assortment of components.

TV/VIDEO SELECTION

To view the picture from a VCR,

camcorder, or TV game, you must put theVIDEO TV in VIDEO mode first. Press TV/VIDEO

to select VIDEO mode. The word “VIDEO” displays briefly on-screen. Press TV/VIDEO again to return to TV mode.

1. To connect the TV to a VCR

VCR	Front of TV
	CHANNEL	VIDEO AUDIO
	ENTER RESET
To Audio/
Video OUT VIDEO		AUDIO
	(not supplied)

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

2. To connect the TV to a VIDEO Game

The TV also can be used as a display device for many video games. However, due to the wide variety of different types of signal generated by these devices and subsequent hook-up variations required, they have not all been included in the suggested connection diagrams. You will need to consult each

component's owner's manual for additional information.

FrontCHANNEL ofVIDEOTVAUDIO

VIDEO Game ENTERRESET

To Audio/Video OUT

(not supplied)

3. To connect the TV to a camcorder

To playback from the camcorder, connect the camcorder to the TV as shown.

Front of TV

ENTERRESCHANNELET VIDEOAUDIO

To AV OUT jack	7
(not supplied)

J3M21921A(E)_P02-07 7 14/12/2004, 5:01 PM