6
4. SLEEP Button - To set the TV to turn off after a preset
amount of time, press the SLEEP button on the remote
control. The clock will count down 10 minutes each time
the button is pressed in the order of 120, 110, 100, ······ 20,
10, 0. After the sleep time is programmed, the display will
disappear then reappear momentarily every ten minutes to
remind you the sleep timer function is operating. To
confirm the sleep time setting, press the SLEEP button
once and the remaining time will be momentarily displayed.
To cancel the sleep timer, press the SLEEP button
repeatedly until the display turns to 0.
5. VOL (VOLUME) + / – Buttons - Press the + button to
increase or the – button to decrease the volume level.
6. MENU Button - Press to display the on-screen menu function.
7. SET + / – Buttons - Press to select the desired setting
during on-screen operations.
8. RESET Button - Press to reset the on-screen picture
adjustments to their factory preset positions.
9. TV/VIDEO Button - Switches between the TV and external
device inputs.
10. RECALL Button - When you press this button, the channel
number will appear in the upper right corner of the screen.
Press the button again to remove it from the screen.
11. MUTE Button - To turn off the sound, press this button
once. The TV will be silenced and the word “MUTE” will
appear on the screen. The muting feature can be released
by pressing the MUTE button again or one of the VOL + or
– buttons.
12. CH (CHANNEL) + / – Buttons - Press the CH + button to
change to a higher numbered channel set into memory.
Press the CH – button to change to a lower numbered
channel set into memory.
13. ENTER Button - Press to enter or select information for
on-screen operations.
14. MTS Button - Switches sound between mono, stereo, and
SAP when receiving broadcasts in stereo or SAP.
15. 1/2 Button - Switches between captions channel 1 and
captions channel 2 in the closed caption mode.
16. CAP/TEXT Button - Press to switch between normal TV
and the two closed caption modes (captions or text), when
available.
REMOTE CONTROL

1. Open the battery compartment cover.

2. Install two

AAA

(penlight size) batteries.

HOW TO INSTALL BATTERIES

Before using the remote control, batteries must first be

installed.

3. Replace the battery compartment cover.

1. POWER Button - Press to turn on the TV. Press again
to turn off the TV.
2. Direct Channel Selection / Channel Number Buttons (0–9)
- Allow direct tuning of any channel.
3. CH RTN Button - Repeatedly press CH RTN to toggle
back and forth between the last two channels you tuned.
Use two
AAA
size
penlight
batteries (supplied) for the
remote control. The batteries may last approximately one
year depending on how much the remote control is used.
For best performance, it is recommended that you replace
the batteries on a yearly basis or when the remote operation
becomes erratic.
Caution:
Never throw batteries into a fire.
Notes :
Be sure to use AAA size batteries.
Dispose of batteries in a designated disposal area.
Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
If the remote control does not operate correctly, or if the
operating range becomes reduced, replace batteries with
new ones.
When necessary to replace batteries in the remote
control, always replace both batteries with new ones.
Never mix battery types or use new and used batteries in
combination.
Always remove batteries from remote control if they are
dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid
from leaking into the battery compartment.
MENU
VOL
SLEEP
MUTE
CH RTN RECALL
VOL
+
ENTER
CH –
CH +
123
456
7
0
89
SET
+
1/2
CAP/TEXT
RESET MTS
TV/VIDEO
POWER
CT-837
1
2
3
5
6
7
8
9
10
11
12
13
16
4
15
14
3M91721A[En] P02-07 22/12/05, 4:46 PM6