Manuals / Brands / TV and Video / Flat Panel Television / Toshiba / TV and Video / Flat Panel Television

Toshiba 53AX61 Connecting a DVD player/satellite receiver and a VCR, You will need:, one video cable, •one video cable, one coaxial cable, •one S-videocable

1 54

Download 54 pages, 5 Mb

Connecting a DVD player/satellite receiver and a VCR

This connection allows you to watch DVD/satellite, VCR, and TV programs. You can record one TV channel while watching another channel.

You will need:

•one coaxial cable

•two pairs of audio cables (one single and one pair of audio cables for a mono VCR)

•one video cable

•one S-video cable

Stereo VCR

From antenna			VIDEO			AUDIO
From antenna						L	R
	IN from ANT OUT to TV						IN
	IN from ANT OUT to TV
	CH 3						OUT
	CH 4						OUT
	CH 4
	TV
			AUDIO CENTER			ANT( 75 )
			CHANNEL IN
						ANT-1
			ON	OFF
						OUT
				OUT
			R	L	VAR
			R	L	AUDIO
					AUDIO
	S-VIDEO					ANT-2
						ANT-2
	VIDEO		Y		VIDEO
	VIDEO
			PB L		L/
			PB L		MONO
	L/ MONO
	AUDIO		AUDIO	AUDIO
			PR
	R		R		R
		COLOR	R		R
		COLOR
	VIDEO 1 VIDEO 2 STREAMINPUT
	IN	DVD IN		OUT
From satellite			AUDIO
dish (for satellite			AUDIO
			OUT
			L
receiver only)			L
receiver only)	IN from ANT		R
			R

S-VIDEO VIDEO

OUT OUT

DVD player/satellite receiver

Note:

You can use a regular video cable instead of an S-video cable, but the picture quality will decrease. If you use an S-video cable between the TV and DVD player/satellite receiver, make the audio connections only and remove the regular video cable.

Do not connect a regular video cable and an S-video cable to Video-1 (or Video-2) at the same time or the picture will be distorted.

The unauthorized recording of television programs, video tapes, DVDs, and other materials may infringe upon the provisions of copyright laws.

Introduction


Connecting	yourTV


Usingthe	RemoteControl


Settingup	yourTV


UsingtheTV’s	Features


Appendix


Index

53AX61(E) 7

Contents

Owner's Record Important Information Precautions Page Introduction Welcome to Toshiba Exploring your new TV Connecting your TV Connecting a VCR Connecting a cable converter box Connecting a cable converter box and a VCR Connecting a DVD player/satellite receiver and a VCR Connecting a DVD player with ColorStream® (component video) and a VCR Connecting two VCRs Connecting a camcorder Connecting an audio system Connecting an A/V receiver Using the remote control Preparing the remote control for use Installing the remote control batteries Remote control functional key chart Page Programming the remote control for use with your audio/video devices Verifying the device code (990) For example, to verify the device code for the VCR mode: 1.Repeatedly press MODE until the VCR mode is selected 2.While holding down RECALL, press 9, 9 3.Press 1 ➝ 0 blinks Device code table Page Page Page Learning about the remote control Setting up your TV Learning about the menu system Changing the on-screendisplay language Selecting the antenna input Adding channels to the TV’s memory Changing channels Adjusting the color convergence Using the TV’s features Adjusting the channel settings To clear a favorite channel: 2.Press y or z to highlight FAVORITE CH2, for example 3.Press x or • to display the FAVORITE CH2 menu. CH INPUT will be highlighted 4.Press yz•x to highlight the channel you want to clear, and then press ENTER Connecting yourTV Page Watching picture-in-picture(PIP) Switching the main and PIP pictures Changing the position of the PIP window Freezing the PIP picture Using the multi-windowfeature Using the LOCKS menu Using the V-CHIPmenu MPAA RATING (Independent rating system for movies) 1.From the LOCKS menu, select MPAA RATING 3.Press x or • to display the MPAA RATING menu (below right) 4. Press • to lock (“X”) or x to unlock (“✓”) Setting yourTV Locking channels Locking the video inputs Locking the front panel buttons Changing the PIN code Adjusting the picture Saving your new picture preferences To save your new picture preferences: 2.Press y or z to highlight SAVE NEW PREFERENCE 3.Press x or •. When saved, the menu displays “DONE.” Using the flesh tone feature Selecting the color temperature Resetting your picture adjustments Watching video input Selecting the video source labels Using the closed caption feature Setting the sleep timer Setting the clock Adjusting the sound Using the surround sound feature To turn on the surround sound feature: 1.Select the STEREO mode (see “Selecting stereo/SAP broadcasts” on page 43) 2.Press MENU, and then press x or • until the THEATER menu appears 3.Press y or z to highlight SURROUND Adjusting the sound quality To adjust the sound quality: 2.Press y or z to highlight the item you want to adjust Resetting your audio adjustments center (0) Using the sub-basssystem (SBS) To turn on the SBS: 2.Press y or z to highlight SBS To adjust the SBS level: 4.Press y or z to highlight SBS LEVEL Selecting the Audio OUT sound To select the Audio OUT sound: 1.Press MENU, then press x or • until the AUDIO menu appears 2.Press y or z to highlight AUDIO OUT 3.Press x or • to highlight MAIN or PIP Selecting the background of the menu display Displaying on-screeninformation Viewing the demonstration mode Understanding the auto power off feature Understanding the last mode memory feature Appendix Specifications Troubleshooting For additional information, visit our web site: www.toshiba.com/tacp Index