Toshiba dimensions Toshiba G8000 Series UPS, Installation Planning Guide for 150kVA UPS

TOSHIBA G8000 Series UPS

Installation Planning Guide for 150kVA UPS

Standard System: 480V Input, 480Y/277V Output

General Mechanical Information

Dimensions		Weight
(W x D x H)
Inches		Lbs.
55.1 x 31.5 x 78.75	2,756

Approximate Full-Load

Heat Loss

Btu/Hr

37,914

Primary AC Input (480V 3-Phase / 3-Wire)

Maximum Input Power			Suggested External	Suggested Minimum Feeder	Suggested Maximum Feeder Length
	Demand		Overcurrent Protection	Wire Size Per Phase	For Min. Wire Size in Steel Conduit
kVA	PF	Amps	Amps	AWG or kcmil at 75º C Temp. Rating	Feet
150	>0.98	180	225 AT	(1) x 4/0	480

Alternate (Bypass) AC Input (480V 3-Phase / 4-Wire)

Maximum Input Power			Suggested External	Suggested Minimum Feeder	Suggested Maximum Feeder Length
	Demand		Overcurrent Protection	Wire Size Per Phase / Neutral	For Min. Wire Size in Steel Conduit
kVA	PF	Amps	Amps	AWG or kcmil at 75º C Temp. Rating	Feet
150	0.8	180	225 AT	(1) x 4/0 / (2) x 3/0	380

Battery Input (360VDC Nominal)

	Battery Capacity Required	Maximum Discharge	Suggested External	Suggested Minimum Feeder
	for Full Load Output	at Full Load Output	Overcurrent Protection	Wire Size Per Phase
	kWB	Amps DC	Amps
				AWG or kcmil at 75º C Temp. Rating
127.7		448	500 AT	(2) x 4/0

Suggested Maximum Feeder Length For Min. Wire Size in Steel Conduit

Feet

70

AC Output (480/277V 3-Phase / 4-Wire)

	Rated Output Power			Suggested External	Suggested Minimum Feeder		Suggested Maximum Feeder Length
				Overcurrent Protection	Wire Size Per Phase / Neutral		For Min. Wire Size in Steel Conduit
	kVA	PF	Amps	Amps	AWG or kcmil at 75º C Temp. Rating		Feet
150		0.8	180	225 AT	(1) x 4/0 / (2) x 3/0	380

Important Notes:

1.Maximum Current required at Primary AC Input based on full load output and maximum battery charging current.

2.Output load conductors are to be installed in separate conduit from input conductors.

3.Control wires and power wires are to be installed in separate conduits.

4.Recommended AC input and output overcurrent protection based on continuous full load current per NEC.

5.Wiring shall comply with all applicable national and local electrical codes.

6.Grounding conductors to be sized per NEC Article 250-122. Neutral conductors to be sized per NEC Article 310.15.

-Primary AC Input: 3φ, 4-wire + ground.

-Alternate AC Input: 3φ, 4-wire + ground.

-AC Output: 3φ, 4-wire + ground.

-DC Input: 2-wire (Positive/Negative) + ground.

7.Nominal battery voltage based on the use of VRLA type batteries (2.0 volts/cell nominal).

8.Maximum battery discharge current based on lowest permissible discharge voltage of 1.6 VPC.

9.DC wires should be sized to allow not more than a 2-volt drop at maximum discharge current.

10.Weights do not include batteries or other auxiliary equipment external to the UPS.

11.Sizing calculations based on the following assumptions:

-Not more than 3 current-carrying conductors installed in steel conduit in ambient temperature of 30 degrees C.

-Temperature rating of conductors and terminals: 90 deg. C.

-Feeder distance calculations based on NEC Tables 8 and 9 data, allowing for 2% AC voltage drop.

-Reference: 2002 NEC Handbook. Consult latest edition of applicable national and local codes for possible variations.

12.Ratings of wires and overcurrent devices are suggested minimums. Consult with a registered Professional Engineer within your local area for proper size selections.

TOSHIBA INTERNATIONAL CORPORATION

13131 West Little York Road

Houston, TX 77041

Telephone: (800) 231-1412

Fax: (713) 896-5212

Corporate Web Site: www.tic.toshiba.com

Group Web Site: www.toshibaups.com

Rev. 1.03 Page 1 of 1 G8000-IPG-150kVA