To control a cable TV converter:

Program the remote control to recognize the brand of your converter. The shaded buttons shown on the right will control the cable TV converter.

Press the CABLE button whenever you control the cable TV converter.

Programming the remote control for use with a VCR or a cable TV converter

This remote control is pre-programmed to operate Toshiba VCRs. To use VCRs or cable converters other than Toshiba models, you must follow the steps below before you operate your remote control.

1.Refer to the “VCR code table” or “Cable TV converter code table” on pages 12-13 to find the number that corresponds to the brand name of your VCR or converter.

If more than one number is listed, try each one separately until you find the one that works.

2.Turn on the device (VCR or converter) you wish to program the code.

3.Press the matching device button “VCR” (or “CABLE”) and ENT at the same time. The device button will be illuminated by the back-light to indicate that it is in the program mode. Perform the following steps while the back-light is on (about 20 seconds).

4.Point the remote control toward the VCR (or converter) and press the Number buttons to enter the three digit code number for your brand of VCR (or converter).

•If the right number was entered, the VCR (or the converter) should turn off.

•If the VCR (or the converter) does not respond to the remote control, repeat steps 1 to 4 with another code number until the device turns off.

The back-light will blink to confirm the storage.

5.Press the device button (CABLE or VCR) to release the program.

6.Press TV to control the TV.

For future reference, write down the code numbers you used:

VCR code

_____________________

Cable code

_____________________

 

 

 

 

 

 

 

POWER

POWER

MTS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIMER

 

TV

 

CABLE VCR

 

 

Device buttons

 

 

 

 

 

 

 

 

1

 

 

2

 

3

 

 

Channel ▲▼

4

 

 

5

 

6

 

CH

 

 

 

 

 

Channel

7

 

 

8

 

9

 

 

 

 

 

 

 

Number

 

 

 

 

 

CH RTN

VOL

 

 

 

 

 

 

100

 

 

0

 

ENT

 

 

ENT

 

 

AP

 

RE

 

 

 

.C

T

 

S

 

 

 

C

 

 

 

 

ET

 

S

 

 

 

 

 

 

E

 

 

 

 

 

 

 

X

 

D

 

 

 

 

 

 

T

 

X

 

 

 

 

 

 

I

 

 

 

 

 

ADV

 

 

 

 

 

 

 

 

 

 

 

FAV

 

 

 

MENU/

 

FAV

 

-

 

 

 

ENTER

 

+

 

ADV

MUTE RECALL TV/VIDEO SURROUND

Note:

•Each time you replace the batteries, you must reprogram the remote control.

•Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled “VCR1/VCR2.”

If your VCR has this kind of switch, it may not respond to any of the code numbers for your VCR brand name. In this case, set the switch to the other position (VCR1 or

VCR2) and reprogram the remote control.

Introduction

Connecting your TV

Using the Remote Control

Setting up your TV

Using the TV’s Features

Appendix

Index

11