Manuals
/
TP-Link
/
Computer Equipment
/
Network Card
TP-Link
TL-WN851ND
manual
To connect using QSS, PBC Push Button Configuration method
Models:
TL-WN851ND
1
17
39
39
Download
39 pages
2.18 Kb
14
15
16
17
18
19
20
21
Specifications
Install
Features
To connect using TWCU
Page 17
Image 17
Page 16
Page 18
Page 17
Image 17
Page 16
Page 18
Contents
Rev 1.1.0
TL-WN851ND 300Mbps Wireless N PCI Adapter
COPYRIGHT & TRADEMARKS
FCC RF Radiation Exposure Statement
FCC STATEMENT
National Restrictions
CE Mark Warning
2400.0-2483.5 MHz
Country
Product Description 300Mbps Wireless N PCI Adapter
DECLARATION OF CONFORMITY
Shenzhen, P. R. China
ETSI EN 300 328 V1.7.1
CONTENTS
Chapter 1 Product Overview
1.1 Package Contents
1.2 Introduction
300Mbps Wireless N PCI Adapter
1.4 Hardware Overview
1.3 Features
Status
Working Status
2.2 Software Installation
Chapter 2 Installation
2.1 Hardware Installation
TL-WN851ND
5. Click Install to continue the setup
6. The utility and drivers will install. This may take 1~2 minutes
TL-WN851ND
3.1 To connect using TWCU
Chapter 3 Connect to a Wireless Network
To connect using TWCU
To connect using QSS
automatically connect to your target network next time if you tick Connect automatically
4. You have now successfully connected to your network. Click Close to enjoy the Internet
3.2.1 PBC Push Button Configuration method
3.2 To connect using QSS
3. The adapter will be connecting to the target network
3.2.2.1. Enter the PIN from your AP device
3.2.2 PIN method
3.2.2.2. Enter a PIN into your AP device
2. The adapter will be connecting to the target network
TL-WN851ND
3.3.1 In Windows
3.3 To connect using Windows built-in wireless utility
3.3.2 In Windows Vista
2. The utility will display any available wireless networks in your area. Highlight the wireless network you would like to connect and then click Connect
3.3.3 In Windows XP
Or double-click the utility icon to load the utility configuration page. Click Advanced in the tools section and then select Use Windows wireless configuration tool in the figure shown below. Click OK when Figure 3-25 appears to continue
3. The utility will display any available wireless networks in your area. Click on a network displayed using the SSID and click the Connect button
4.1 Profile
Chapter 4 Management
The following items can be found on the screen
4.1.3 Delete a profile
4.1.2 Modify a profile
4.2 Advanced
4.3 About
Chapter 5 AP Mode
¾ SoftAP mode Select to enable or disable the function
6.1 Uninstall the utility software from your PC
Chapter 6 Uninstall Software
6.2 Uninstall the driver software from your PC
Environmental and Physical
Appendix A Specifications
Normal
Appendix B Glossary
¾ Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS
Top
Page
Image
Contents
