Manuals
/
TP-Link
/
Computer Equipment
/
Network Card
TP-Link
manual
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide
Models:
TL-WN881ND
1
22
40
40
Download
40 pages
16.7 Kb
19
20
21
22
23
24
25
26
Specs
Install
Features
To connect using TWCU
Page 22
Image 22
Page 21
Page 23
Page 22
Image 22
Page 21
Page 23
Contents
TL-WN881ND 300Mbps Wireless N PCI Express Adapter
Rev
COPYRIGHT & TRADEMARKS
FCC STATEMENT
FCC RF Radiation Exposure Statement
2400.0-2483.5 MHz
CE Mark Warning
National Restrictions
Country
ETSI EN 300 328 V1.7.1
DECLARATION OF CONFORMITY
Product Description 300Mbps Wireless N PCI Express Adapter
ETSI EN 301 489-1 V1.8.12008 & ETSI EN 301 489-17 EN60950-12006
CONTENTS
Package Contents
Conventions
1.1 Product Overview
1.2 Features
Chapter 1 Introduction
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide
Working Status
1.3 Hardware Overview
Status
Flashing Quickly
2.1 Hardware Installation
Chapter 2 Installation
2.2 Software Installation
300Mbps Wireless N PCI Express Adapter User Guide
TL-WN881ND
5. Click Install to continue the setup
6. The utility and drivers will install. This may take 1~2 minutes
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide
Chapter 3 Connect to a Wireless Network
3.1 To connect using TWCU
3. If word None appears behind the SSID, this means the network to be connected is not security-enabled and you can connect to the network without entering a key. To prevent outside intrusion and safeguard your network, it is strongly recommended to set a password to your router or access point
4. You have now successfully connected to your network. Click Close to enjoy the Internet
3.2 To connect using QSS
3.2.1 PBC Push Button Configuration method
3. The adapter will be connecting to the target network
3.2.2 PIN method
2. The adapter will be connecting to the target network
TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide
3.3 To connect using Windows built-in wireless utility
3.3.1 In Windows
3.3.2 In Windows Vista
2. The utility will display any available wireless networks in your area. Highlight the wireless network you would like to connect and then click Connect
3.3.3 In Windows XP
Or double-click the utility icon to load the utility configuration page. Click Advanced in the tools section and then select Use Windows wireless configuration tool in the figure shown below. Click OK when Figure 3-25 appears to continue
3. The utility will display any available wireless networks in your area. Click on a network displayed using the SSID and click the Connect button
Chapter 4 Management
4.1 Profile
The following items can be found on the screen
4.1.2 Modify a profile
4.1.3 Delete a profile
4.2 Advanced
4.3 About
Chapter 5 AP Mode
¾ SoftAP mode Select to enable or disable the function
Chapter 6 Uninstall Software
6.1 Uninstall the utility software from your PC
6.2 Uninstall the driver software from your PC
Normal
Appendix A Specifications
Environmental and Physical
Appendix B Glossary
¾ Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS
Top
Page
Image
Contents
