Traulsen UC27WT, UC27HT, UR48HT, UR48DT, UR48WT, UR30HT VIII. Other, VI. d Cleaning the Exterior

Inside Door Panel

VI. CARE & MAINTENANCE (cont’d) VII. MISC. OPERATIONS

VI. c - REPLACING THE GASKETS (cont’d):

gently hitting with a mallet until the gasket is com- pletely seated in place (see figure 9 for proper gasket placement).

Gasket Assembly

Fig. 9

Vertical Gasket

Retainer

NOTE: The gasket may appear too large, but if it is installed as indicated above it will slip into place.

VI. d - CLEANING THE EXTERIOR:

Exterior stainless steel should be cleaned with warm water, mild soap and a soft cloth. Apply with a damp- ened cloth and wipe in the direction of the metal grain.

Avoid the use of strong detergents and gritty, abra- sive cleaners as they may tend to mar and scratch the surface. Do NOT use cleansers containing chlorine, this may promote corrosion of the stainless steel.

Care should also be taken to avoid splashing the unit with water, containing chlorinated cleansers, when mopping the floor around the unit.

For stubborn odor spills, use baking soda and water (mixed to a 1 TBSP baking soda to 1 pint water ratio).

VI. e - CLEANING THE INTERIOR:

For cleaning both stainless steel and anodized alumi- num interiors, the use of baking soda as described above is recommended. Use on breaker strips and as well as door gaskets. All interior fittings are remov- able without tools to facilitate cleaning.

VI. f - REPLACING THE INTERIOR LIGHT BULB: Turn the unit OFF (the ON/OFF switch is located be- hind the top louver panel). Next, remove the light cover by squeezing the sides together, which releases the tabs from the holding slots. Replace the burned out light bulb with a similar type appliance bulb.

To replace the light cover, squeeze the sides together and reinsert tabs in to the holding slots and release to lock in place.

VII. a - ADJUSTING THE SHELVES:

For shelves mounted on pins, first select the desired location and remove the white plastic covers in the interior back and sides by rotating them counter-clock- wise. Next, remove the existing shelf pins by rotating them counter-clockwise. Install the pins in the desired location and tighten by rotating clockwise. Make sure the pin is securely tightened down, don’t over tighten. Slide the shelf into its new position. Replace the white plastic covers into the holes vacated by the shelf pins.

VII. b - REMOVING THE DRAWER PANS:

For your convenience, each drawer contains two (2) removable anodized aluminum pans. They can be re- moved for cleaning simply by opening the drawer and lifting them out.

VII. c - REMOVING THE DRAWERS:

Prior to removing the drawers, food and pans should be removed. The drawer is heavy and care should be taken to keep feet clear. To remove, pull the drawer out as far as possible. Then, lift the drawer and con- tinue to pull until the drawer is free of the unit. To replace, simply reverse the process.

VIII. OTHER

VIII. a - SERVICE INFORMATION:

Before calling for service, please check the following:

Is the electrical cord plugged in?

Is the fuse OK or circuit breaker on?

Is the power switch “ON”?

If there is no air movement in the freezer unit, it may be in defrost cycle. Wait 35 minutes to see if the unit will restart.

Do the lights work?

If after checking the above items and the unit is still not operating properly, please contact an authorized Traulsen service agent. A complete list of authorized service agents was provided along with your Traulsen unit. If you cannot locate this, you may also obtain the name of a service agent from the Tech Service page of our website: www.traulsen.com.

If service is not satisfactory, please contact our in- house service department at:

Traulsen & Co., Inc. 4401 Blue Mound Road Fort Worth, TX 76106 (800) 825-8220

Traulsen & Co., Inc. reserves the right to change speci- fications or discontinue models without notice.

-7-