Troy-Bilt 12234 owner manual Operation, PRE-START Preparation, Stopping Starting the Engine

Section

4

Operation

WARNING

Before operating the unit, carefully read and understand all safety, control and operating instructions in this Manual, the separate Engine Owner’s Manual and the decals on the machine.

Failure to follow these instructions can result in serious personal injury.

PRE-START PREPARATION

c.Retighten the depth adjustment knob.

10.Reconnect the spark plug wire.

DANGER

GASOLINE IS HIGHLY FLAMMABLE AND ITS VAPORS ARE EXPLOSIVE.

Follow the gasoline safety rules in this Manual (Section 1) and in the separate Engine Owner’s Manual.

B

A

Figure 4: Primer bulb (A) and fuel-return tube (B).

Before starting the engine, perform the following checks and services:

1.	Disconnect the spark plug wire from
the spark plug.
2.	Move the engine On/Off switch to the

Failure to follow gasoline safety instruc- tions can result in serious personal injury and property damage.

11.Add gasoline to the fuel tank.

C

Close

Open

OFF position.
3.	Check that all wires and cables are
properly and securely connected.
4.	Check the six plastic cable ties (J,
Figure 2). Be sure that cables and ties are
positioned as shown. Cables must not be
kinked or jammed in the handlebar.
5.	Adjust handlebar height to desired po-
sition (see Section 2).
6.	Check hardware for tightness.
7.	Check engine oil level (see Engine
Owner’s Manual).
8.	Check the air filter (see Engine Owner’s
Manual).
9.	Adjust the tilling depth as follows:
	a. Loosen tilling depth adjustment
	knob (A, Figure 3).

A

B

C

Figure 3

b.Move wheel bracket (B, Figure 3) up in relation to height adjustment bar

(C). Moving bracket upward results in shallower tilling, which is recom- mended for initial use.

IMPORTANT: Do not move the wheel bracket any higher than the top of the adjustment bar.

IMPORTANT: Read the separate Engine Owner’s Manual before starting the engine. Never use stale or contaminated gasoline or oil/gas mix. The engine must be stopped and cool before adding gas.

Fill the fuel tank with unleaded gasoline (with a pump octane rating of 86 or higher) according to the directions in the separate Engine Owner’s Manual. The engine is a vertical type, GX 31 model.

STOPPING AND

STARTING THE ENGINE

Stopping the Engine

WARNING

Do not squeeze the Throttle/Tines Con- trol Lever while starting engine.

Tines may propel the machine forward if the engine speed is advanced from idle. Failure to comply can result in personal injury or property damage.

To stop the engine, move the On/Off Switch (A, Figure 2) to the OFF position.

NOTE: The On/Off switch wire must be securely connected at both ends. Check regularly to ensure that the switch wire is securely connected to the switch and the engine.

Starting the Engine

NOTE: Do not squeeze Engine Throttle/Tines Control Lever (G, Figure 2) when starting engine.

1.Move the On/Off Switch (A, Figure 2) to the ON position.

Figure 5: Choke lever.

2.To start a cold engine, move the choke lever (C, Figure 5) to the CLOSED posi- tion. To restart a warm engine, leave the choke lever in the OPEN position.

3.To start a cold engine, or after refueling an engine that has run out of fuel, press the priming bulb (A, Figure 4) repeatedly until fuel can be seen in the clear-plastic fuel-return tube (B). To restart a warm engine, it is not necessary to press the priming bulb.

4.Move to the starting position (Figure 6), keeping your feet positioned safely away from the tines.

5.Place one hand on the upper handlebar to stabilize the machine. Use the other hand to pull the recoil start rope lightly until you feel resistance, then pull briskly. Let the rope rewind slowly after each pull.

NOTE: An alternate stabilization method is to stand in the starting posi-

tion (Figure 6), but place

one hand on the carrying handle while pulling the starter rope with the other

hand.

6. If the choke lever was moved to the CLOSED position to start the engine, gradually move

it to the OPEN position as the engine warms up.

Figure 6

7