Quick Start Guide
4.The mounting hardware consists of two tile rails and a ‘C’ plate (these are supplied with the
tile and align them parallel to each other on either side of the hole, and with the ends positioned over the ceiling T grid. Insert the ‘C’ plate through the hole and snap the tabs onto the tile rails as shown. Position directly over the hole in the ceiling tile and secure with the fixing screws supplied. Note that the provision of multiple fixing holes in the tile rails allows the speaker to be positioned away from the centre of the tile if desired.
5.Plug the connector into the socket in the loudspeaker’s terminal cup. The connector is polarised to avoid the possibility of
6.Connect the safety tab to a separate support point. Consult construction codes in your region.
7.Insert the speaker into the ceiling and secure the fixing arms. Offer the loudspeaker into the ceiling until the back of the front baffle rim touches the ceiling tile. Turn the attachment screws to tighten the fixing arms. Note that the first 1/4 turn rotates the arm outwards and subsequent turns tighten the tab down onto the ceiling tile. DO NOT OVERTIGHTEN.
8.Adjust the voltage tap selector for desired level. The selector is located on the front baffle, and should be adjusted before fitting the grille. In some installations it may be preferable to leave grilles off until final adjustment of the tap selectors has been completed for all loudspeakers.
TCS-50T
6 |
| 6 | 1 |
| |
0 |
|
|
| ||
3 |
|
|
|
|
|
0 |
| 1 |
|
|
|
|
| 0 |
|
|
|
|
| 0 |
|
|
|
15 | V |
|
| 5.7 | |
| V |
| |||
|
|
|
| ||
|
| 0 |
|
|
|
|
| 7 |
|
| 5 |
1 | 6 | 60 | 0 | 1 | |
| |||||
| 3 | ||||
|
|
|
TCS-35T
3 |
|
| 6 | 1 | ||
1 | 0 |
|
|
| ||
|
| 1 |
|
|
| |
5 |
|
|
|
|
| |
|
|
| 0 |
|
|
|
|
|
| 0 |
|
|
|
7.5 |
| V |
|
| 75.3 | |
|
| V |
| |||
|
|
|
|
| ||
|
|
| 0 |
|
|
|
|
|
| 7 |
|
| 5. |
|
| 6 |
|
|
| 7 |
| 1 | 30 | 5 | |||
|
| 1 |
9.Apply the logo badge to the grille in the desired location if required, and fit the loudspeaker grille by pressing the grille firmly into place until it is flush with the rim.
Painting before Installation
The loudspeaker’s white finish matches most décor schemes and does not need further finishing. However where interior design requires an alternative colour this can be easily accomplished. The loudspeaker can either be painted before installation, or where the rim needs to be finished at the same time as the ceiling the rim can be painted after locating in the ceiling. The speaker will accept almost any type of emulsion or
Clean the rim and grille with a light solvent such as white spirit. Do not use gasoline, kerosene, acetone, MEK, paint thinner, harsh detergents or other chemicals, all of which may damage the loudspeaker. After cleaning, apply two coats of paint, using a roller or brush, or by spraying.
Painting the Speaker with the Ceiling
Using the paint shield provided, paint the speaker and remove the shield. To paint the grille, first remove the logo and grille cloth backing. It is advisable to spray the grille to avoid the mesh becoming clogged with paint from a roller or brush, which may impair the sound quality. Replace the grille cloth and the logo.