Model CEZ260 Speakerphone with 13 Number Memory User’s Guide
Important Information
NOTICE: This product meets the applicable Industry Canada technical specifications.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
The equipment must be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe systems, if present, are connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
NOTES: This equipment may not be used on coin service provided by the telephone company.
Interference Information
This equipment generates and uses radio frequency energy which may interfere with residential radio and television reception if not properly installed and used in accordance with instructions contained in this manual. Reasonable protection against such interference is ensured, although there is no guarantee this will not occur in a given installation. If interference is suspected and verified by switching this equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient the radio/television receiver’s antenna, relocate the equipment with respect to the receiver, plug the equipment and receiver into separate circuit outlets. The user may also wish to consult a qualified radio/television technician for additional suggestions. This equipment has been fully tested and complies with all limits for Class B computing devices pursuant to part 15 FCC Rules and Regulations.
Telephone Network Information
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company, where practicable, may notify you that temporary discontinuance of service may be required. Where prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately.
The telephone company may make changes in its communications facilities, equipment, operations or procedures where such action is required in the operation of its business. If these changes are expected to affect the use or performance of your telephone equipment, the telephone company will likely give you adequate notice to allow you to maintain uninterrupted service.
Notice must be given to the telephone company upon termination of your telephone from your line.
REN Number
On the bottom of this equipment is a label indicating, among other information, the Ringer Equivalence Number (REN) for the equipment.
The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you should contact your local telephone company.
REN Number is located on the cabinet bottom.
© 2009 Uniden America Corporation, Fort Worth, Texas
Printed in China
Hearing Aid Compatibility (HAC)
This telephone system meets FCC/Industry Canada standards for Hearing Aid Compatibility.
Licensing
Licensed under US Patent 6,427,009.
|
|
|
|
|
|
|
|
| CAUTION: |
|
|
|
|
| RISKOFELECTRICSHOCK |
|
|
WARNING:TO |
|
| DONOTOPEN |
|
|
THE LIGHTNING | CAUTION: TO REDUCE THE | THE EXCLAMATION | |||
PREVENT FIRE OR | FLASH AND ARROW | RISK OF ELECTRIC SHOCK, DO | POINT WITHIN THE | ||
ELECTRICAL SHOCK | HEAD WITHIN THE | NOT REMOVE COVER (OR | TRIANGLE IS A | ||
TRIANGLE IS A | BACK). NO USER | WARNING SIGN | |||
HAZARD, DO NOT | WARNING SIGN | SERVICEABLE PARTS INSIDE. | ALERTING YOU OF | ||
EXPOSETHIS | ALERTING YOU OF | REFER SERVICING TO | IMPORTANT | ||
“DANGEROUS | QUALIFIED SERVICE | INSTRUCTIONS | |||
PRODUCT TO RAIN | VOLTAGE” INSIDE | PERSONNEL. | ACCOMPANYING | ||
OR MOISTURE. | THE PRODUCT. |
|
|
| THE PRODUCT. |
| SEE MARKING ON BOTTOM / BACK OF PRODUCT | ||||
Introduction
CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference.
Short Glossary of Terminology Used in this Manual
Hook switch. The part of the phone that pops up to activate the phone line when the handset is lifted from the base.
Before You Begin
Parts Checklist
Make sure your package includes the following items:
Base | Handset | Handset | Desk stand | |
|
| cord | (might be | telephone |
|
|
| attached to | line cord |
|
|
| base) |
|
Telephone Jack Requirements
To use this phone, you need an RJ11C type modular telephone | Wall plate | |
jack, which might look like the one pictured here, installed in | Modular | |
your home. If you don’t have a modular jack, call your local | ||
phone company to find out how to get one installed. | telephone | |
line jack | ||
Important Installation Information | ||
|
CAUTION: Disconnect the phone cord from the wall outlet before installing or replacing the batteries.
•Never install telephone wiring during a lightning storm.
•Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface.
•Use caution when installing or modifying telephone lines.
•Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. It should add:
Installing and Replacing the Batteries
Your Caller ID phone uses 4
IMPORTANT: You will have approximately 90 seconds to replace the batteries before the memories stored are lost. Please read the instructions before replacing the batteries and have the batteries ready to be inserted beforehand.
IMPORTANT: If you are not going to use the telephone for more than 30 days, remove the batteries because they may leak and damage the unit.
1. Disconnect the telephone line cord. If necessary, remove the desk stand from the back of the base.
2. Release the latch on the battery compartment and remove the cover.
3. Insert 4
4. Snap the battery compartment door back into place and replace the desk stand.
6. Connect the line cord and check your memory locations.
NOTE: If the low battery icon appears
in the display, you need to replace the batteries. It is important that you replace the batteries as soon as possible in order to maintain Caller ID operation.
Installing the Phone
Your phone should be placed on a level surface, such as a desk or table top, or you can mount it on a wall.
Location
Your phone features a speakerphone for ease of use and convenience during a phone conversation. At any time during a conversation, you can lift the handset to stop using the speakerphone. Likewise, when you are using the handset, press the SPEAKER button and place the handset in the cradle to switch to the speakerphone.
For best speakerphone performance, avoid the following:
•Areas with high background noise. (The microphone might pick up these sounds and prevent the speakerphone from going into the receiving mode when you finish talking.)
•Surfaces affected by vibration.
•Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can generate an echo effect.
Attaching the Desk Stand
Turn the phone over . Insert the hooks marked DESK into the notches marked DESK. Press in on the tabs and snap the stand into place.
Connecting the Handset
1. Connect one end of the coiled
handset cord to the jack on the handset.
2. Plug the other end of the 
coiled handset cord to the jack
on the base.
3. Place the handset in the cradle.
Connecting the
Telephone Line
1. Connect one end of the straight telephone line cord to the jack on the back of the base.
2. Connect the other end to a wall phone jack.
3.Set the RINGER volume switch located at the back of the base to the desired loudness.
OFF - Telephone will not ring. LO - Sound will be lowest.
HI - Sound will be loudest.
NOTE: The unit is properly installed if you pick up the handset and hear the dial tone. Otherwise, recheck all installation steps.
Wall Mounting
Your speakerphone can also be mounted on a wall plate (not included).
REMINDER: To prevent the handset from falling out of the cradle while the phone is hanging on the wall, you must switch both the handset hook and the desk stand to their 
• On the front of the base, pull the handset hook out of the slot. Rotate the hook 180 degrees and flip it from
front to back. Slide it back into the slot.
• .Turn the base over. Press in on the
tabs and remove the desk stand
from the back of the base.
• Rotate the stand 180 degrees, and insert the hooks marked WALL into the notches marked
WALL. Press in on the tabs and
snap the stand into place.
• Connect the telephone line cord to the wall jack and the phone.
If desired, wrap any excess cord around the cord hooks as shown.
• Place the mounting slots over the pins on the wall plate, and
slide the base down to lock it into place.
Base Layout
STORE | MENU | Display | DELETE |
| |
(button) | (button) |
|
| (button) | VOLUME |
|
|
|
|
| |
|
|
|
|
| (button) |
|
|
|
|
| LEFT, RIGHT |
|
|
|
|
| (buttons) |
|
|
|
|
| A, B, C |
|
|
|
|
| (quick call |
|
|
|
|
| buttons) |
|
|
|
|
| MUTE |
|
|
|
|
| (button) |
|
|
|
|
| SPEAKER |
|
|
|
|
| (button) |
|
|
|
|
| DIAL |
|
| FLASH/exit | REDIAL/pause | (button) | |
*/TONE |
| ||||
(button) | (button) | (button) |
| ||
Setting Up the Caller ID Menu
You should not plug the telephone into the modular jack while setting up the Caller ID menu.
1.Press the MENU button, to access the menu feature configuration mode.
#1. >ENG FRA ESP (CID language default English)
#2. CONTRAST (default level is 3).
#3. LOCAL AREA CODE
#4. TONE/PULSE (Default is tone dialing).
2.Press the MENU button to scroll through the 4 menu screens.
3.Use the LEFT or RIGHT button to select the desired setting.
NOTE: You have 20 seconds following an entry before the phone returns to the Summary Screen.
Display Language
This adjustment allows you to display the Caller ID prompts in English, French, or Spanish.
1.Press the MENU button until ENG FRA ESP appears in the display.
2.Use the LEFT or RIGHT button to select ENG, FRA, or ESP.
3.Press the MENU button again to save.
Contrast
This adjustment allows you to adjust the contrast of the display.
1.Press the MENU button until CONTRAST shows in the display.
2.Use the LEFT or RIGHT button to select level 1, 2, 3, 4, or 5.
3.Press MENU button again to save.
Local Area Code
The telephone uses the programmed area codes to determine the number format to display when a valid Caller ID signal is received. Numbers that match the local area code are displayed as seven digits and are used for dialing back previous numbers. Entering your local area code will also help you immediately know if the call is local or long distance when viewing the CID records in the display.
NOTE: If you make a mistake and want to start over, press the DELETE button to delete all of the digits.
1.Press the MENU button until LOCAL AREA CODE shows in the display.
2.Use the number pad to enter the area code.
NOTE: If you need to edit your entry, use the LEFT or RIGHT button to move left or right and
3.Press the MENU button to save.
Dialing Mode
This adjustment allows you to select tone
1.Press the MENU button until 4 TONE PULSE shows in the display
2.Press either LEFT or RIGHT button to select the dialing mode. The default is Tone dialing.
3.Press the MENU button again to save.
NOTE: The phone will exit Set Up after 20 seconds if no buttons are pressed.
REMINDER: The time and date are programmed automatically when the first Caller ID record is successfully received after set up.
Telephone Basics
You can use the telephone by speaking into and listening through the handset, or by using the speakerphone.
Receiving a Phone Call
1.Lift the handset or press SPEAKER to answer the call.
2.Replace the handset in the cradle or press the SPEAKER button to hang up.
Making a Phone Call
1.Lift the handset or press the SPEAKER button. Wait for a dial tone.
2.Dial the telephone number you want to call.
3.Replace the handset in the cradle, or press the SPEAKER button to hang up.
Volume
You may adjust the handset and speakerphone volume independently with the VOLUME button or the LEFT or RIGHT buttons. Both handset receiver volume level and speakerphone volume levels are saved in memory.
Adjusting the Handset Receiver Volume
While using the handset, you can adjust the speaker volume by pressing the VOLUME button continuously or pressing the LEFT or RIGHT buttons after pressing the VOLUME button. REC (Handset Receiver) volume shows in the display.
Adjusting the Speakerphone Volume
While using the speakerphone, you can adjust the speaker volume by pressing the VOLUME button continuously or pressing the LEFT or RIGHT buttons after pressing the VOLUME button. SPK volume level shows in the display.
Redial
You may redial the last number you called by pressing the REDIAL/pause button after you hear a dial tone.
NOTE: The redial feature holds the last number (up to 32 digits) that you dialed in memory. If you pressed any other numbers after dialing the phone number (for example, when accessing a
If you get a busy signal, press REDIAL/pause again without hanging up.
Mute
Use the MUTE button to interrupt a phone conversation to talk privately with someone else in the room. A conversation can be muted while using the speakerphone or handset.
1.Press the MUTE button. The mute indicator lights up.
2.Press MUTE again to turn it off.
Flash
Press FLASH/exit to activate special features of your telephone network, such as call transfer, or special services from your local telephone company, such as call waiting.
Temporary Tone Dialing
If you have pulse (rotary) service and want to access customer calling services (such as telebanking and long distance services) that require tone dialing, you can use this feature to temporarily change from pulse to tone service.
After dialing the telephone number and connecting to the customer calling service,
1.Press and release the *TONE button.
2.When you hang up, the telephone automatically returns to pulse dialing mode.
TIP: Temporary Tone can also be used while storing numbers in memory by pressing *TONE at the necessary point in the storage sequence.
Speakerphone Use
Note the following guidelines when using the speakerphone:
•The speakerphone works similar to a
•Stay reasonably close to the phone so that you can be clearly heard by the person to whom you are talking.
•You can adjust the speaker volume by pressing the volume button continuously or pressing the review button 5 or 6 after pressing the volume button.
•The speakerphone indicator light comes on when the speakerphone is in use.
Caller ID (CID) Features
IMPORTANT: In order to use all of the features of this telephone, you must subscribe to two separate services available from your local telephone company: the standard Name/Number Caller ID Service to know who is calling when the phone rings and Call Waiting Caller ID Service to know who is calling while you are on the phone.
CID Summary Screen
The Summary Screen shows the current time, date, and number of new calls to review. It is displayed until any button is pressed.
NOTE: The number of new calls is displayed until all new calls have been reviewed.
Receiving and Storing CID Calls
This unit receives and displays information transmitted by your local phone company. This information can include the phone number, date, and time; or the name, phone number, date, and time. The unit can store up to 75 calls for later review. When the memory is full, a new call automatically replaces the oldest call in memory. NEW appears in the display for calls received that have not been reviewed.
Reviewing CID Records
•Press the LEFT or RIGHT button to view the call records.
•Press the RIGHT button to scroll through the call records from the oldest to the newest.
•Press the LEFT button to scroll through the call records from the most recent to the oldest.
•When all of the records have been viewed, START/END appears in the display.
Deleting CID Records
•To delete the record shown in the display, press the DELETE button once.
•To delete all records while reviewing, press and hold the DELETE button for about three seconds. DELETE ALL? appears in the display. Press DELETE again to complete.
Dialing Back
When reviewing Caller ID records, you can dialback the numbers on the display by pressing the DIAL button.
NOTE: If PICKUP PHONE shows in the display, no other changes to the number can be made. The information sent from the telephone company is known to be a valid number for dialing back (used only in very limited areas). Once you pickup the phone, the number is automatically dialed.
If You Programmed Your Local Area Code
1.Use either LEFT or RIGHT button to display the number you want to dial.
2.Press the DIAL button.
•If you see a number with seven digits (i.e.
•If you see a number with 11 digits (i.e.
NOTE: A timer (10 seconds
3.If you are at
7 digits: |
|
10 digits: | |
11 digits: | long distance code 1 + |
| number (i.e. |
4.To dial the displayed number, and the phone is
If You Did Not Program Your Local Area Code
1.Use the LEFT or RIGHT button to display the number you want to dial. You will only see
2.See steps 2 through 4 in the previous section to complete the dialback process.
Caller ID Display Messages
The following messages shows the status of the phone or provides Caller ID information:
BLOCKED CALL | The caller of the incoming call is registered as “Private Number” and |
| their Caller ID information is withheld. |
CALL WAITING | Indicates a call is waiting on the line. |
INCOMPLETE | Caller information has been interrupted during transmission or the |
DATA | phone line is excessively noisy. |
NO CALLS | The caller memory is empty. |
NO DATA | No Caller ID information was received. |
START/END | You are at the beginning or the end of the Caller ID memory log. |
UNKNOWN | The incoming call does not have Caller ID service or their service |
CALLER | area is not linked to yours. If UNKNOWN CALLER appears along with |
| a calling number, the name information for that number was not |
| available. |
Memory
You may store information in any of the following memory locations: 0 to 9, or quick call buttons; A, B, or C. See “Storing a Pause in Memory” and “Temporary Tone Dialing” for more information.
NOTE: This model retains all user memory even if the batteries are removed and/or telephone line has been interrupted or disconnected.
Storing a Name and Number in Memory
1.Press the STORE button. LOCATION? shows in the display.
2.Press the desired memory location (0 to 9, or quick call buttons; A, B, or C.)
NOTE: You may select memory locations by pressing 5 or 6 to scroll through the memory locations or press the 0 - 9, or quick call buttons; A, B, or C.
3. Press the STORE button again to confirm the memory location.
NOTE: If necessary, to erase existing memories, or if you make a mistake, use the DELETE button.
4.Use the number keys to enter the telephone number (up to 32 digits) and press the STORE button to save. (The unit will not dial a phone number in this mode.) The cursor automatically moves to the text line for name entry.
5.Use the number keys to enter the name of the person associated with the telephone number you just entered. More than one letter is stored in each of the number keys.
For example, to enter the name BILL SMITH, press the 2 key twice for the letter B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L.
NOTE: The flashing cursor automatically moves to the next position or you may press the LEFT or RIGHT button to move the cursor to the next position.
Press the 5 key 3 times for the second letter L. Press the arrow key (5) two times to insert a space, and press the 7 key 4 times for the letter S. Press the 6 key once for the letter M. Press the 4 key 3 times for the letter I. Press the 8 key for the letter T. Press the 4 key twice for the letter H.
6.Press the STORE button to save the name.
7.To enter another name and number in a different memory location, return to step 1 and repeat the process.
Changing a Stored Number
Repeat the storage sequence under Storing A Name and Number in Memory, and use the DELETE button to delete the old number before entering the new number.
Erasing a Stored Name & Number
1.Press the STORE button.
2.Press the memory location (0 to 9, or quick call buttons; A, B, or C) to be erased.
3.Press the DELETE button.
Copying Caller ID Memories to
User Memory
1.Press the LEFT or RIGHT button to view the caller number and name you want to copy.
2.Press the STORE button.
3.Press the memory location
4.Press the STORE button to enter the edit mode, and then press the STORE button again to edit the name.
NOTE: You may select a different memory location by pressing 5 or 6 to scroll through the memories or press 0 - 9, or quick call buttons; A, B, or C.
5.Press the STORE button to confirm and save, and wait for three seconds to exit.
NOTE: If the name you want to enter is longer than 12 characters, only the first 12 characters will be copied into memory.
Storing a Redial Number to Memory
1.Press the STORE button.
2.Press any key
3.Press the STORE button again to confirm.
4.Press the REDIAL/pause button, and then press the STORE button again.
5.Enter name, if necessary, and then press the STORE button to confirm.
Copying a Redial Number to Memory
1.Press the REDIAL/pause while
PICKUP PHONE.
2.Press the STORE button.
3.Press any key
4.Press the STORE twice.
5.Enter name, if necessary, and then press the STORE button again to confirm and save.
Dialing a Number Stored in Memory While On-hook
1.Press the DIAL button
2.To select a memory, press any key
NOTE: You may select a different memory location by pressing LEFT or RIGHT to scroll through the memories or pressing key (0 - 9,or quick call buttons; A, B, or C.).
3.Press the SPEAKER button, or pick up the handset to dial the displayed number.
Dialing a Number Stored in Memory While Off-hook
1.Lift the handset, or press the SPEAKER button.
2.Press the DIAL button then press a memory location button. - OR -
1.Lift the handset, or press the SPEAKER button.
2.Press the DIAL button, then use the review (5 or 6) button to scroll through the stored memory locations to find the desired number.
3.Press the DIAL button again to dial the stored number.
Cascade Dialing
This process allows you to dial a succession of stored numbers from separate memory locations. This is useful when you must dial several sequences of numbers, such as with frequent calls via a telephone company long distance provider.
For example | Memory location |
Local access number of long distance company | 6 |
Authorization code (ID) | 7 |
Long distance phone number | 8 |
1.Pick up the handset or press SPEAKER.
2.Press DIAL button, then press number “6” for the memory location.
3.Press DIAL button, then press number “7” for the memory location.
4.Press DIAL button, then press number “8” for the memory location.
5.The number dials automatically.
Storing a Pause in Memory
The REDIAL/pause button has dual functionality and becomes a pause button when pressed in sequence after the STORE button. It is valid only when storing a number into memory locations. Use the REDIAL/pause button to insert a pause when a delay is needed in an automatic dialing sequence. For example, when you must dial a 9 to get an outside line or when you enter codes to access your long distance company.
NOTE: A pause is 3 seconds in length and you can store more than one, if a longer pause is needed.
Pre-Dialing
1.With the handset on the cradle, enter the telephone number you wish to call. The telephone number shows in the display.
2.Lift the handset or press the SPEAKER button and the number automatically dials.
NOTE: Use the DELETE button to delete an incorrectly entered number.
Troubleshooting Tips
No Dial Tone
•Check all cabling to make sure that all connections are secure and not damaged.
•Check hook switch: Does it fully extend when handset is lifted from cradle?
No Information is Shown After the Phone Rings
•Are you subscribed to Caller ID service from your local telephone company?
•Be sure to wait until the second ring before answering.
Phone Dials in Pulse with Tone Service
•Make sure T/P MODE is set to TONE DIAL. Phone Won’t Dial Out with Pulse Service
•Make sure T/P MODE is set to PULSE DIAL. Phone Does Not Ring
•Make sure ringer switch is ON.
•You may have too many extension phones on your line. Try unplugging some extension phones.
•Check for dial tone. See Troubleshooting Tips for No Dial Tone.
Incoming Voice Volume Low
•Are other phones off hook at same time? If so, this is normal condition as volume drops when additional phones are used at once.
•Check the handset receiver or speaker volume.
Memory Dialing
• Make sure you entered the numbers correctly into memory.
General Product Care
To keep your phone working and looking good, follow these guidelines:
•Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).
•DO NOT expose to direct sunlight or moisture.
•Avoid dropping and other rough treatment to the unit.
•Clean with a soft cloth.
•Never use a strong cleaning agent or abrasive powder because this will damage the finish.
•Retain the original packaging in case you need to ship it at a later date.
One-year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials & craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate & be of no further effect 12 months after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner’s manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit & return it to you without charge for parts, service, or any other cost (except shipping & handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE & ENTIRE WARRANTY PERTAINING TO THE PRODUCT & IS IN LIEU OF & EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, & you may also have other rights which vary from state to state. This warranty is void outside the United States of America & Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner’s manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). Disconnect the battery from the Product & separately secure the battery in its own separate packaging within the shipping carton. The Product should include all parts & accessories originally packaged with the Product. Include evidence of original purchase & a note describing the defect that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
Uniden® is a registered trademark of Uniden America Corporation.
The pictures in this manual are used for examples only. Your actual phone may not look exactly like the pictures.
