Operating Instructions

For 4 Function

DTV Remote Control

1Introduction

The remote control is designed to operate the DTV series set top boxes and the majority of TV, VCR/DVD and AUDIO equipment on the market.

2Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries.

STEP1 Remove the battery compartment cover on the back of your remote control.

STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below.

STEP3 Replace the battery compartment cover.

3

Button Functions

 

*Tip : The equipment will turn off when

 

the correct three-digit code

 

 

 

number has been entered. You can verify you have selected the correct code by pressing the [MUTE] button, the equipment should turn on or turn off.

*Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.

STEP4 Store the three-digit code number by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.

*Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list. Make sure that the VCR/VOD button is in the VCR position when using your VCR.

STEP3 Press the [CH+] or [CH-] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH+] or [CH-] button as soon as the equipment turns off.

*Tip : You can verify that you selected the correct code by pressing the [MUTE] button. The TV should either turn on or turn off.

STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.

C. To Find the Three Digit

Code Number That was

Stored in the Device.

STEP1 Press the [DEVICE] button (TV, VCR or AUD) you wish to verify and the [SELECT] button

D. Programming a second TV to VCR Mode.

STEP1 Turn on the TV you wish to program.

STEP2 Press the [VCR] button to be programmed and the [SELECT] button simultaneously for 3 seconds. The [VCR] device LED will turn on.

*Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on.

STEP3 Press the [TV] button to access the TV code table.

STEP4 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables.

*Tip : You can verify that you selected the correct code by pressing the [MUTE] button. The equipment should either turn on or turn off.

STEP5 Store the three-digit code number by pressing the [VCR]

STEP3 Press the [DEVICE] button you wish to store in the [SYSTEM ON/OFF] button and repeat this until you stored all the power commands into the [SYSTEM ON/OFF] button.

STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] device LED will blink twice to confirm the saving.

F. Program the Volume

Controls.

By following the steps below, you can program the volume controls (Volume UP, Volume Down and MUTE) to your TV, VCR and Audio.

The default volume control settings on the remote control is TV volume control. If you wish you can control the volume via your cable box or audio equipment. Use the following steps to change the volume control settings:

G. Programming For

Advanced Function.

In the CABLE mode, the [ * ] button can be programmed to act as a macro or favorite channel button to send out up to 10 commands with one button press.

STEP1 Press the [CBL] button to select the CABLE mode.

STEP2 Press the [ * ] button and [SELECT] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds.

STEP3 Press up to 10 buttons you wish to store. The [CBL] button LED will blink once for each command entered.

STEP4 Press the [CH+] button to store the functions that are selected. The [CBL] device LED will blink twice to confirm the storage of functions.

H. Low Battery Warning.

When the battery is low (2.0V-2.3V) and needs to be replaced with fresh

Universal Remote Control, Inc.

www.universalremote.com

OCE-0002A Rev 12(05/31/07)

4Operations

Default State :

Device Default: DTV Cable box.

Volume Default: TV volume and mute through the TV, with the option of controlling volume and mute through the Cable box or Audio. Refer to Section F for programming the volume and mute through your Cable box or Audio.

System On/Off button:

This button is designed to send out power commands for two, three or all four devices with one button press. Please refer to section E for details.

5Programming the Remote Control

A. Programming For Your Devices.

The remote control can be programmed by pressing in a three digit code number that corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit code numbers are listed in the code table of the instruction manual.

STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUDIO).

STEP2 Press the [DEVICE] button (TV , VCR or AUD) to be programmed and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed.

*Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on.

STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables.

B. Auto Search Method.

If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search

Method to find the correct three-digit code number for your equipment by the following steps:

STEP1 Turn on the equipment you wish to operate.

STEP2 Press the [DEVICE] button (TV, VCR or AUD) to be programmed and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on.

*Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on.

simultaneously for 3 second. The device LED will turn on.

*Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on.

STEP2 Press the [INFO] button.

The device LED will blink number of times indicating the number of each digit of the code number. Each digit is separated by a 1 second pause of the LED being turned off.

Example : One blink, three blinks and eight blinks with an interval of 1 second of LED being turned off, indicates the code number 138.

Note : Ten blinks is equal to the number 0.

button once again. The [VCR] device LED will blink twice to confirm that the code has been stored.

E. Programming the System On/Off Button.

This button is pre-programmed to turn on all devices with one button press, however you can also program to turn on one or two devices by following these steps:

STEP1 Press the [CBL] button.

STEP2 Press the [SYSTEM ON/OFF] button and the [SELECT] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds.

STEP1 Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. The [CBL] device LED will turn on.

*Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on.

STEP2 Press the [ VOL + ] button.

STEP3 Press the [ CBL ], [ AUD ] (whichever applicable) button. The [CBL] device LED will blink twice to confirm the programming.

To return to original state:

If you wish to restore the TV volume control in CABLE mode, repeat the above steps by pressing [ TV ] button in

batteries, device LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on equipment.

I. Memory Lock System.

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

J. Write your device Set-up codes.

TV

Set-up Code Number :

 

VCR

Set-up Code Number :

 

 

 

 

 

AUDIO Set-up Code Number :

Page 1
Image 1
Universal Remote Control 4 Function DTV Remote Control operating instructions Introduction, Replacing Batteries

4 Function DTV Remote Control specifications

The Universal Remote Control 4 Function DTV Remote Control is an essential accessory for simplifying your home entertainment experience. Designed to streamline the operation of multiple devices, this remote offers a user-friendly interface and a compact design, making it suitable for both seasoned tech enthusiasts and those who prefer straightforward solutions.

One of the primary features of this universal remote is its compatibility with various device types, including TVs, DVD players, and cable boxes. This versatility allows users to consolidate their remotes into one, reducing clutter and improving convenience. The remote is engineered to support a wide range of brands, ensuring that it can easily integrate into your existing setup without requiring any complicated configurations.

The 4-function design focuses on the most commonly used operations — power, volume control, channel selection, and input selection. This simplicity is particularly useful for users who may find complex remotes intimidating. The large, well-labeled buttons are easy to read and press, making it accessible for individuals of all ages, including children and the elderly.

In terms of technology, the Universal Remote Control utilizes infrared (IR) signals for communication with your devices. This reliable technology ensures that commands are transmitted accurately, allowing for swift response times when changing channels or adjusting the volume. The remote is equipped with a robust battery-efficient mechanism, which prolongs the lifespan of its batteries, meaning less frequent replacements.

Another notable characteristic of this remote is its lightweight structure, making it comfortable to hold and easy to handle during extended viewing sessions. Its ergonomic design is coupled with a sleek aesthetic, fitting seamlessly into any modern living room décor.

Additionally, programming this universal remote is a straightforward process, thanks to built-in code search functionality. Users can quickly find the right code for their devices without the frustration often associated with setup.

Overall, the Universal Remote Control 4 Function DTV Remote Control embodies user-centric design, advanced compatibility, and innovative technology, making it an excellent choice for anyone looking to enhance their home entertainment experience with ease and efficiency.