8
3.2 12 Volt DC Charging
The START-IT™system also comes with a DC/DC charging cord, for recharging the unit from the 12 volt DC cigarette lighter socket in a vehicle or boat. Note: This recharging method will NOT recharge the unit as effectively as recharging from a 110 volt AC outlet. The 12 volt DC recharging procedure is recommended only when it is necessary, as continued use of the 12 volt DC recharging procedure may shorten the battery system’s life.
WARNING: DO NOT RECHARGE FOR MORE THAN 6 HOURS MAXIMUM USING 12 VOLT DC METHOD.
1.NOTE: If unit is fully discharged, it is recommended that the vehicle being used for recharging be left running while the unit is being charged via the 12 volt DC method.
2.Insert one end of the DC/DC charging cord into the 12 volt DC cigarette lighter receptacle on the vehicle or boat.
3.Insert the plug at the other end of this power cord into the 12 volt DC receptacle on the front panel of the unit.
4.Charge the unit until the green FULL LED indicator lights when Charge Status Indicator Button is pressed.
DO NOT EXCEED 6 HOURS MAXIMUM.
5.When charging is completed, remove the power cord and store in a safe place.
3.3 110 Volt AC Charging Using VEC070 Automatic Battery Charger (purchased separately)
1.Install the charger’s DC wire with battery clips.
2.The jumpstarter has a high-current switch for turing the heavy-duty clamps ON and OFF, make sure the Safety switch is turned OFF.
3.Connect the POSITIVE (RED) DC Battery Clip to the RED POSITIVE jumpstarter clamp.
4.Connect the NEGATIVE (BLACK) DC Battery Clip to the BLACK NEGATIVE jumpstarter clamp.
5.Connect the charger to an AC outlet or extension cord rated at 18 AWG or larger.
6.Turn ON the Safety switch and observe the RED LED on the charger for proper operation.
7.Charge the START-IT™ until the green Charged LED lights when Charge Status Button is pressed. Then continue charging for another hour.
8.When charging is complete, Turn OFF the Safety switch.
9.Disconnect the charger from the AC outlet or extension cord.
10.Disconnect the charger’s battery clips from the jumpstarter’s clamps.
11.Store the charger as described in it’s Owner’s Manual.
12.Place the jumpstarter back into service.
3.4 Estimated Battery Life
Table I shows the relationship of the frequency of use between recharging and the expected number of discharge/recharge cycles
Table I — Estimated Battery Life
| AVERAGE NUMBER OF USES | POTENTIAL TOTAL NUMBER | |
| (JUMPSTART OR DISCHARGES) | OF JUMPSTART OR DISCHARGE CYCLES | |
| BETWEEN RECHARGES | . . . .(LIFETIME OF UNIT BATTERY) | |
| | | |
| 1 | . . . . . . . . . . 1000+ | |
| 5 | . . . . . . . . . . . 700+ | |
| 10 | . . . . . . . . . . . 500+ | |
| | | |
5
1. INTRODUCTION
Congratulations on selecting the Vector® START-IT™ JUMPSTART SYSTEM & 12 VOLT DC POWER SUPPLY. Please read this guide carefully before use to ensure optimum performance and avoid damage to the unit or items with which you are using it. This manual describes models VEC025MB (Blue) and VEC025MY (Yellow).
The Vector® START-IT™ JUMPSTART SYSTEM & 12 volt DC POWER SUPPLY is a compact, durable and portable jumpstart system for vehicles and boats that have a standard 12 volt battery system. This self-contained, recharge- able system will start most boats and vehicles without the need for a host or 110 volt AC power supply.
It can also be used as a safe, portable source of 12 volt DC electric power in remote locations and/or emergency situations. It is ideal for use with Vector® 12 volt DC cordless, portable, rechargeable products and MAXX® DC/AC Power Inverters. Use the START-IT™to:
-Jumpstart:
Any vehicle with a standard 12 volt DC battery system; boat, truck, car, airplane, RV, personal watercraft, snowmobile, tractor, etc.
-Operate: 12 volt DC
Fans, inflators, fluorescent work lights, cellular phones*, air compressors, inflators, spotlights, TVs, portable radios, cassette, CD players and more. *Can quick-charge a cellular phone by using the phone’s 12 volt DC adapter cord.
-Operate: Certain 110 volt AC Accessories (requires DC to AC power inverter, sold separately)
The START-IT™ SYSTEM has an easy-to-read, series of LED (Light Emitting Diode) charge indicators that show when the unit is fully charged or the level of charge in the battery. Charge level can be viewed when the charge status
button is pressed. A 12 volt DC cigarette lighter-type socket is provided for use with appliances that can operate from a vehicle cigarette lighter. This allows maximum portability and utility when the START-IT™is used in remote locations.
For maximum convenience, the START-IT™can be recharged from any standard 110 volt AC or 12 volt DC power source using the built-in 12 volt socket and the appropriate charging/adapter cord. When depressed, the PUSH FOR STATUS switch will show the battery ‘s power level status (from Low to Full). The green LED FULL indicator illuminates when the unit is fully recharged. An ON/OFF switch operates the built-in work/emergency light.
WARNING:
Lead-acid batteries generate hydrogen gas during normal operation. More gas is generated when the battery is charging. Hydrogen gas is: EXPLOSIVE • POISONOUS TO BREATHE • HIGHLY FLAMMABLE
To avoid an explosion and/or the possibility of being splashed with battery acid:
•NEVER allow the red and black clamps to touch each other or a common metal object.
•ONLY attempt to jumpstart a vehicle or boat in a WELL ventilated area.
•ALWAYS CONNECT THE RED (+) CLAMP TO THE POSITIVE (+) BATTERY TERMINAL FIRST.
•DO NOT CONNECT THE BLACK (-) CLAMP TO THE NEGATIVE (-) BATTERY TERMINAL.
•CONNECT THE BLACK (-) CLAMP TO A NON-MOVING METAL PART ON THE ENGINE.
CAUTIONS:
I.To avoid possible damage that may shorten the unit’s working life, protect this unit from direct sunlight, direct heat and/or moisture.
2.This system is designed to be used ONLY on boats or vehicles with 12 volt DC battery systems.
3.This system is NOT designed to be used as a replacement for a vehicular battery.
RECOMMENDATIONS FOR OPTIMUM PERFORMANCE OF THE START-IT™ JUMPSTART SYSTEM: WARNING: NEVER insert anything other than the supplied power/recharging cords or recommended appliance power/recharging cords into the charging/power sockets on this unit.
IMPORTANT: The safety ON/OFF switch should be in the OFF position when the unit is charg- ing, or not in use.
