Vestax PMC-55 owner manual Program Input Section

55/E／面付け 00.9.12 4:44 PM ページ 9

PROGRAM INPUT SECTION

PGM 1

LINE IN 2

1	L			R
	INPUT	LINE 1
2
	PHONO 1			LINE 2
		TRIM		4
		+3
		MIN		MAX
3		0 BAL
		-3		5
		-8
			L	R
		-13		EQ CUT
		(dB)		6
	EQ
	HI
	-24dB			+6dB (0dB)
	MID
7
	-24dB			+6dB (0dB)
	LOW
	-24dB			+6dB (0dB)
8	AUX	OUT
	PRE			POST
	MASTER 1		MASTER 2
9	IN			IN
	OUT			OUT
10	C.F. ASSIGN			11
	A MASTER B
				CUE
	10
	9
	8
	7
	6
	5			12
	4
	3
	2
	1
	0

○1 LINE IN 2, 4, 6, 8 (RCA)

Used for line level input. Connect CD player or tape deck to these jacks. Line level musical instruments with stereo outputs such as rhythm machine or sampler are also good for LINE IN. And they are located on the top panel for quick and easy access. This is particularly useful for "visiting" equipment.

○2 INPUT SELECTOR

Used to select the input (two LINE or one PHONO) to be sent to each PGM channel.

○3 INPUT LEVEL METER

The LED level meters indicate the input signal level of each PGM channel.

○4 GAIN CONTROL

Adjusts the input level of each channel. Set INPUT FADER (12) to 7-8 position, adjust GAIN so that INPUT LEVEL METER(3) shows about 0dB.

○5 BALANCE CONTROL

Adjusts the stereo balance for each PGM channel. Can be used for adjusting the unbalanced stereo image caused by strong Anti-Skating setting. Clockwise rotation from center position increase volume of R over L channel. Counter clockwise rotation increase volume of L channel over R.

○6 EQ CUT SWITCH

Press this switch to bypass EQ section.

○7 EQ (HI, MID, LOW)

Adjusts the HI,MID and LOW frequencies for each PGM channel. Each band has following specifications.

HI	8kHz	-24dB~ +6dB	Shelving type
MID	500Hz	-24dB~ +6dB	Peaking type
LOW	80Hz	-24dB~+6dB	Shelving type

○8 AUX ASSIGN SWITCH

Used when sending signal to external effect processor connected to AUX SEND/RETURN (42).

○9 MASTER OUT ASSIGN 1, 2

Used to send the signal from each program to either MASTER OUT 1 or 2 (43). MASTER LOOP is located on MASTER OUT 1.

○10 CROSSFADER ASSIGN

Used to send the signal from each program to either the crossfader (A or B) or the master directory. A for left side of the crossfader, B for right side.

○11 CUE ASSIGN

Used to send the signal from each program to monitor section for headphones monitoring. Signal is sent to CUE OUT (42) too. This allows for sending signal to external sampling unit connected to CUE OUT.

○12 INPUT FADER

Used to adjust the Input level of each program. Usually set at the 7-8 position. This is a detachable fader for the ease of replacement. Replace with IF- 50 when It is worn out.

HOW TO REPLACE THE INPUT FADER

●Remove four screws which hold the fader unit panel.

●Take the unit out with the panel

●Remove a knob and two screws which hold the fader unit.

●Carefully remove the multi-cable connector from the fader unit.

●Insert the connector to the new fader unit.

●Replace the knob and the fader unit to the panel and fix it with screws.

●Replace the fader unit panel and tighten the screws.

5